Aiwa XR-X7 Operating Instructions Manual page 9

Changing the display colour
You can preset up to 3 of your favourite colours you adjusted.
The display colour can be changed to 12 different colours and
3 adjusted preset colours (select colour mode). You can also
select 12 different colours and 3 adjusted preset colours for
each function (function colour mode).
You can select between select colour mode and function colour
mode.
Presetting select colour mode
1 Press COLOR to display "SELECT CL" while the
power is on.
2 Within 4 seconds, turn VOLUME/MULTI JOG until
"COLOR M 1", "COLOR M 2" or "COLOR M 3"
is displayed.
3 Press COLOR.
"A G B " is displayed and "A " flashes.
4 Turn VOLUME/MULTI JOG to select "A ", "G "
or "B ".
- A: adjust amber colour.
- G: adjust green colour.
- B: adjust blue colour.
5 Press COLOR.
6 Turn VOLUME/MULTI JOG to adjust the colour.
"50" is the brightest level.
7 Press COLOR.
8 Repeat steps 4 to 7 to set the desired colour.
9 Press ENTER.
•If power is interrupted for more than approximately 12 hours,
all settings stored in memory after purchase need to be reset.
•If you select "00" in each colour, it displays no colour on
the display.
Select colour mode
1 Press COLOR to display "SELECT CL" while the
power is on.
2 Within 4 seconds, turn VOLUME/MULTI JOG to
select the colour.
3 Press ENTER.
Function colour mode
1 Hold down COLOR until "F-CL" is displayed.
2 Within 4 seconds, turn VOLUME/MULTI JOG so
that "CL EDIT" is displayed.
3 Press ENTER.
The source name and colour number flashes on the
display.
If there is no operation for 4 seconds, setting is cancelled.
4 Turn VOLUME/MULTI JOG to select a source,
then press ENTER.
5 Turn VOLUME/MULTI JOG to select the colour,
then press ENTER.
6 Repeat steps 4 and 5 to determine the colours
for other sources.
7 Press ENTER.
Changing the colour mode
1 Hold down COLOR until "F-CL" is displayed.
2 Within 4 seconds, turn VOLUME/MULTI JOG to
select "F-CL ON" or "F-CL OFF".
- F-CL ON: function colour mode
- F-CL OFF: select colour mode
3 Press ENTER.
If there is no operation for 4 seconds, setting is cancelled.
Setting the clock
1 Hold down SHIFT and press CLOCK on the remote
control.
When the unit is turned off, you can also press a or
ENTER.
2 Press f or g to set the time.
Each press changes the time in 1-minute steps.
Holding these buttons down will vary the time in 10-minute
units.
If f or g is not pressed within 4 seconds, setting
is cancelled.
•You can also turn VOLUME/MULTI JOG to the right to
advance the time and to the left to move the time back.
The speed with which the time changes varies according
to how fast you turn VOLUME/MULTI JOG.
3 Press a or ENTER.
The time display stops flashing and the clock starts from
00 seconds.
To display the time while the power is on
Hold down SHIFT and press CLOCK on the remote control.
The time will be displayed for 4 seconds.
To switch to the 24-hour standard
Display the time and press s within 4 seconds.
With each press, the clock alternates between 12- and 24-
hour standard time.
Tip:
In the 12-hour standard, "AM12:00" indicates midnight and
"PM12:00" noon.
If the clock display flashes when the unit is turned
off
There has been a power interruption. Reset the clock.
En
9