http://www.xiaoyu163.com SPECIFICATIONS <EZ, K> 3 7 63 1515 0 MAIN UNIT CX-LX7 GENERAL Power requirements 230 V AC, 50 Hz TUNER Power consumption EZ: 50 W FM tuning range 87.5 MHz to 108 MHz K: 55 W FM usable sensitivity (IHF) 16.8 dBf Power consumption in FM antenna terminal...
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 E C B E C B B C E E C B KTA1266GR 2SA1979O/Y 2SB1677 CSC4115BC 2SA1980G 2SD2619 2SC2240GR 2SC5342Y CC5551 E C B 2SK360E DTC114ES 2SK2158 DTC114TKA 2SA1235F 2SC4115SRS KRA102S 2SC2714O 2SA933SRS KRC107S 2SC3052F...
http://www.xiaoyu163.com IC DESCRIPTION IC, LC78622NE 3 7 63 1515 0 Description Pin No. Pin Name DEFI Defect detection signal (DEF) input. ("L" is applied when not used.) For PLL/Test input. (Connected to 0V) Phase comparison output to control the external VCO. VVSS –...
Page 35
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Description Pin No. RVSS – Rch 1-bit DAC/Rch ground. Normally 0V. RCHO Rch output. RVDD – Rch power supply. MUTER Rch muting output. (Not used) XVDD – Power supply of crystal oscillator. XOUT For the connection of a 16.93MHz crystal oscillator.
Page 36
http://www.xiaoyu163.com IC, LA9241ML 3 7 63 1515 0 Description Pin No. Pin Name For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF FIN2 signal and subtraction from it create an EF signal. FIN1 For the connection of the pickup photodiode. For the connection of the pickup photodiode.
Page 37
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description The HFL (high frequency level) signal is used to judge whether the main beam is positioned on the pit or on the mirror. SLOF Sled servo off control input. CV–...
Page 38
http://www.xiaoyu163.com IC, LC876564V-5V69 3 7 63 1515 0 Pin No. Pin Name Description O-CD CLK CD IC control clock output. O-CD CE CD IC control chip enable output. I-CD WRQ Input standby for CD subcode Q output. I-CD DRF Detect CD RF level. I-CD SUBQ CD IC data input.
Page 39
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description O-DATA PLL, function IC control data output. O-CLK PLL, function IC control clock output. O-FUNC CE Function IC control chip enable output. O-STANDBY Standby LED ON / OFF control output. VSS2 GND.
http://www.xiaoyu163.com ADJUSTMENT <TUNER / CD / AMP – MICON> 3 7 63 1515 0 < TUNER SECTION > <U, C> 1. Clock Frequency Check 7. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP2(CLK) Settings : • Test point : TP3, TP4 (DC Balance) Method : Set to AM 1710kHz and check that the test point is TP8(Lch), TP9(Rch) (Distortion) 2160kHz ±...
Page 41
http://www.xiaoyu163.com 3 7 63 1515 0 < TUNER SECTION > <EZ, K> 1. Clock Frequency Check 8. FM Tracking Check Settings : • Test point : TP2(CLK) Settings : • Test point : TP8(Lch), TP9(Rch) Method : Set to MW 1602kHz and check that the test point is Method : Set to FM 98.0MHz and check that the test point is less 2052kHz ±...
Page 42
http://www.xiaoyu163.com 3 7 63 1515 0 < TUNER SECTION > <HR> 1. Clock Frequency Check 7. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP2(CLK) Settings : • Test point : TP3, TP4 (DC Balance) Method : Set to AM 1602kHz and check that the test point is TP8(Lch), TP9(Rch) (Distortion) 2052kHz ±...
Page 43
http://www.xiaoyu163.com 3 7 63 1515 0 < CD SECTION > CD PWB PATTERN SIDE PARTS SIDE SFR130 JW13 IC501 1 2 3 IC120 CD Adjustment Method • Perform the adjustments after the machine enters the test mode. • Place the CD mechanism on level ground. •...
Page 44
http://www.xiaoyu163.com 3 7 63 1515 0 < AMP – MICON SECTION > AMP-MICON PWB PATTERN SIDE PARTS SIDE IC301 GND (51pin) CN401 OSC (81pin) L151 1. Clock Adjustment 1) Connect an oscilloscope to test point OSC (IC301 81 pin) and GND (IC301 51 pin). 2) Insert the AC plug while pressing POWER and TUNER / BAND buttons.
http://www.xiaoyu163.com CD TEST MODE 3 7 63 1515 0 1. How to Start the CD Test Mode While pressing the CD FUNCTION button, insert the AC plug to the power outlet. When the test mode started, all lights on the display are lit. 2.
http://www.xiaoyu163.com SPEAKER DISASSEMBLY INSTRUCTIONS SX-LX7 3 7 63 1515 0 1. Remove the speaker net. 4. Take out the rubber bushes 2 , then remove the screws hidden by the bushes. 2. Remove the four screws 1 . 5. Remove the front panel. L 13942296513 3.