Blizzard Power Plow 810SS Assembly & Operation Manual page 10

810SS Pistol Grip Control Functions
There are three switches that operate all of the
810SS Power Plow blade functions:
(A) DRIVE. BOX: UP-Extend, DOWN-Retract
(B) ANGLE: UP-Left, DOWN-Right
(C) PASS. BOX: UP-Extend, DOWN-Retract
B
A
Pistol Grip Control Mount Bracket
The bracket is designed to mount in a variety of
positions (see hole placement above). Use the
hardware provided to secure the bracket to the
skid steer.
Position the pistol grip control into the bracket
and "twist-lock" it into place. Depending on oper-
ator preference, the control can be mounted
vertically or horizontally.
Note: Some skid steer models have safety
devices that rotate in front of the operator when
seated. Do not install the mount bracket such that
it interferes with the operation of these devices.
08
Testing The Snowplow
power source with a minimum of 12 volts.
4. Complete the assembly by attaching the A-frame cover. Align the
holes in the cover with those on the A-frame and secure it with
3/8"-16 x 1-1/2" hex cap screws and 3/8" washers.
Congratulations! You have just completed building the finest snowplow
skid steer attachment available! However, the snowplow's functions still
need to be tested.
C
Testing The Snowplow
1. To test all of the functions on the Power Plow, your snowplow needs
to be properly attached to the skid steer. Follow the mounting proce-
dure on page 9.
2. Once the skid steer plate and the UNIVERSAL MOUNT PLATE on the
A-frame have been locked together (using the locking levers on the
skid steer), complete the hydraulic connections with the skid steer
turned off. Note: Due to the various make and model skid steer avail-
able, hydraulic couplings for the auxiliary hydraulic connections are
not provided. Consult your skid steer's Operation Manual for the
appropriate couplings needed. Once you have identified the appro-
priate hydraulic couplings for your skid steer, make the connections to
both of the 3/4" x 78" hydraulic hoses provided. The hydraulic hose
with the female swivel is attached to the male adapter connector
located in the pressure port ("P") on the manifold. The remaining
hydraulic hose with the 90˚ swivel is attached to the tank port ("T").
Complete the hydraulic installation by making the appropriate connect-
ions at the skid steer.
3. Start the skid steer and begin to initiate the Power Plow's blade func-
tions. Note: Depending on the skid steer model, it may be necessary
to turn on the skid steer's auxiliary hydraulic switch prior to operating
the plow. The left switch operates the DRIVER'S SIDE WING. Push
the switch UP to EXTEND the wing and DOWN to RETRACT the
wing. Push the center switch UP to LEFT ANGLE the snowplow and
DOWN to RIGHT ANGLE. The right switch operates the PASSENGER'S
SIDE WING. Again, pushing up will extend the wing and down will
retract the wing. Upon initiating the switches on the pistol grip control,
you may notice a plow function is slow or delayed. The hydraulic fluid
is filling the cylinders and replacing air in the system. If necessary,
monitor the hydraulic fluid level in your skid steer. Also, look for any
leaks around the manifold, hydraulic hoses and all cylinders.
Congratulations on a successful assembly and installation! Once all of the
blade functions have been tested, your Blizzard Power Plow is ready for
action. Should you need additional support during a plow assembly, con-
tact your local authorized Blizzard Dealer or call our Customer Service
Department toll free at 1-888-680-8600.
WARNING: Always use caution when connecting high-
pressure hydraulic fittings. Hydraulic fluid under pressure
can puncture skin causing serious injury or death. In the
event of a hydraulic leak, relieve hydraulic pressure before
loosening fittings. If injured, seek emergency medical help
immediately.