EN9250 TABLE OF CONTENTS Table of Contents For Your Safety Precautions General Notes Before You Operate The Monitor Installation Instructions 7-13 Operating Instructions 14-18 Technical Support (FAQ) 19-20 Appendix 21-24...
It is the responsibilities of the user to correct such interference. As an NERGY Partner Envision Peripherals Inc. has determined that this product meets the NERGY guidelines for energy efficiency. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
EN9250 PRECAUTIONS ! Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. ! Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
EN9250 GENERAL NOTES SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. • • • • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
Page 6
EN9250 GENERAL NOTES (cont) • • • • Plug & Play DDC1/2B Feature - This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
EN9250 BEFORE YOU OPERATE THE MONITOR FEATURES • 19” (48cm) TFT Color LCD Monitor • Crisp & Clear Display for Windows • Recommended Resolutions: 1280 X 1024 @ 60Hz • ® EPA E NERGY • Ergonomic Design with Height, Pivot, Tilt & Swivel Adjustable Stand •...
EN9250 INSTALLATION INSTRUCTIONS INSTALLING & REMOVING THE BASE Install Remove Figure 1 - Installing and Removing the Base CAUTION: Be careful to avoid pinching or scraping fingers when removing the base.
Page 9
EN9250 INSTALLATION INSTRUCTIONS (Cont) POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
Page 10
EN9250 INSTALLATION INSTRUCTIONS (Cont) Connecting The Cables Figure 2 Connecting Cables AC Power Cord 15-pin D-SUB Cable DVI Cable Audio Cable Turn off your computer before performing the procedure below. 1. Connect the female end of the AC power cord to the AC-in port on the back of the monitor.
Page 11
EN9250 INSTALLATION INSTRUCTIONS (cont) How To Install The INF & ICM Files • • • • This is a Plug & Play monitor. Microsoft Windows will automatically install a Plug & Play driver for it when you first install this monitor. It is not necessary to install the INF driver file included in the floppy diskette or CD if Microsoft Windows successfully installed a Plug &...
Page 12
EN9250 INSTALLATION INSTRUCTIONS (cont) Height, Tilt, Pivot & Swivel Adjustment Your monitor features a multi-adjustable stand that will enable it move 110mm up/down (height adjustment), 25 degree forward/backward (tilt adjustment), 90 degree landscape/portrait (pivot adjustment) and 70 degree side/side (swivel adjustment). To make an adjustment, grasp the monitor with both hands on the right and left edge of the casing and move it to the desired position.
Page 13
EN9250 INSTALLATION INSTRUCTIONS (cont) Preparing To Install The Optional Wall Mount Arm (Not Included) This monitor can be attached to a wall mounting arm you can purchase separately. Turn the power OFF then dis-connect the cables from the monitor before performing the procedure below. Lay the monitor face down on a soft surface.
Page 14
NOTE The Envision EN9250 is in compliance with the most current revision of the VESA 75mm Flat Panel Monitor Physical Mounting Interface (FPMPMI standard). Visit our Monitor Accessories website at www.envisionmonitor.com/accessories.html to purchase a wall mount...
EN9250 OPERATING INSTRUCTIONS EXTERNAL CONTROLS Figure 4 - External Controls 1. Power Button 4. > or Volume 2. LED 5. < or Volume 3. MENU / ENTER Button 6. Auto Adjust / Exit Button • Power Button: Press this button to turn the monitor ON or OFF.
Page 16
EN9250 OPERATING INSTRUCTIONS (cont) • Auto Adjust button / Exit: When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu) or go back to the previous menu. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function.
Page 17
EN9250 OPERATING INSTRUCTIONS (cont) How To Adjust A Setting 1. Press the MENU-button to activate the OSD window (Figure 4). < > 2. Press to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it.
Page 18
EN9250 OPERATING INSTRUCTIONS (cont) The descriptions for function control LEDS Main Main Sub Menu Menu Menu Item Menu Reset Value Description Item Icon Icon Lumina Contrast Contrast from Recall Cool Digital-register. Contrast Value Brightness Backlight Recall Cool Adjustment Brightness Value...
Page 19
EN9250 H. Position Adjust the Setup horizontal position of the OSD. V. Position Adjust the verticalposition of the OSD. Adjust the OSD Timeout timeout. Langua English Set OSD display The Language will language to be set to English. English. Deutsch...
*Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Make sure the Envision Monitor Drivers are installed Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave...
Page 21
EN9250 TECHNICAL SUPPORT (FAQ) (cont) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture.
EN9250 APPENDIX SPECIFICATIONS Driving system TFT Color LCD Size 48cm(19.0") Pixel pitch 0.294mm( H )x 0.294mm( V ) LCD Pane LCD Panel Viewable angle 170° (H) 170° (V) Response time 25 ms R,G,B Analog Interface Video Input Digital interface Separate Sync. H/V TTL H-Frequency 30KHz –...
Page 23
EN9250 APPENDIX (cont) • Switch Auto Adjust Key/Exit • < /Volume • > / Volume • Power Button • MENU/ Enter • External Controls: Functions Contrast • Brightness • Focus • Clock • H.Position • V.Position • Language • (Warm) Color •...