Page 1
EN9110 EN9110 19” LCD Monitor User’s Manual By Envision Peripherals, Inc. www.envisionmonitor.com...
Page 2
As an NERGY Partner Envision Peripherals Inc. has determined that this product meets the WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet.
Page 3
Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. EN9110...
Page 4
EN9110 PRECAUTIONS (cont) For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution.
CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: LCD Monitor 15-pin D-Sub Cable DVI Cable Power Cord External Power Adapter Driver Disk Quick Start Guide (QSG) Warranty, Notices, Warnings & Precautions Booklet Input Not Supported Solution Sheet EN9110...
IEC 60227 (designation H05VV-F 3G 0.75mm ! or H05VVH2-F2 3G 0.75mm ! ) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm ! ) shall be used. EN9110 Remove...
Page 7
INSTALLATIONS INSTRUCTIONS (cont) PREPARING TO INSTALL THE CABLES Remove the wall mounting hole cover. Remove the cable cover. EN9110...
AC outlet. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 2 External Adapter 15-pin D-Sub Cable DVI Cable Power Cord Connecting Cables EN9110...
Page 9
EN9110 INSTALLATION INSTRUCTIONS (cont) Preparing To Install The Optional Wall Mount Arm (Not Included) CONNECTIONS This monitor can be attached to a wall mounting arm you can purchase separately from Ergotron (www.ergotron.com). Turn the power OFF then dis- connect the cables from the monitor before performing the procedure below.
Page 10
Insert the 4 screws into the holes and tighten. Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instrucstions on attaching it to the wall. EN9110...
NOTES Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. Figure 3 EN9110...
Press the power button to turn on the monitor. The power indicator will light up. Figure 4 External Control Button EXTERNAL CONTROLS 1. Auto Config / Exit / Brightness / Contrast 4. MENU / ENTER Power Indicator Power Button EN9110...
When OSD menu is in OFF, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. Power Indicator: Green — Power On mode. Orange — Off mode. EN9110...
6. To exit and save, select the exit function, or leave the monitor alone for 10 seconds. If you want to adjust another function press MENU again and repeat steps 2-4. Figure 5 is used to adjust the The OSD Message EN9110...
Adjusts Blue intensity. The color temperature for 6500°K is x=0.313, y=0.329. The color temperature for 7800°K is x=0.296, y=0.311. Clear old settings of Auto-configuration, re- activates auto-configuration and color temperature to 7800°K. Save user adjustment and exit OSD menu. EN9110 set the...
EN9110 PLUG AND PLAY Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key. *Inspect the monitor’s video cable and make sure that none of the pins are bent. EN9110...
Page 18
For FOCUS and CLOCK adjustment use “dot-pattern” or Win 95/98 shut- down mode pattern . EN9110 *Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO) *Adjust RGB color or select a pre-set color temperature from OSD.
Page 20
1280 × 960 1280 × 960 640 × 480 832 × 624 640 × 400 NOTE: For digital input, the resolution 1280 x 1024 @ 85Hz and 1280 x 960 @ 85Hz are not supported EN9110 75Hz 85Hz 60Hz 75Hz 85Hz 75Hz...
Page 21
EN9110 HOW TO INSTALL THE DRIVER-DISK (INF & ICM FILE) FOR FIRST TIME INSTALL : This is a Plug & Play LCD monitor. Turn off the PC then connect the cables. Power on the PC and it will automatically detect your new monitor.
DDC Clock DDC Data PI N NO. DESCRIPTION Detect Cable DDC-Serial Data H-Sync V-Sync DDC-Serial Clock PI N NO. DESCRIPTION TMDS Data 3+ +5V Power Ground(for+5V) Hot Plug Detect TMDS Data 0- TMDS Data 0+ TMDS Data 0/5 Shield EN9110...
Page 26
N.C. TMDS Data 1- TMDS Data 1+ TMDS Data 1/3 Shield TMDS Data 3- EN9110 TMDS Data 5- TMDS Data 5+ TMDS Clock Shield TMDS Clock + TMDS Clock -...
During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. ) will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below.
Page 28
THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE.