King Canada KC-1401FX Instruction Manual page 3

1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the
tool. Learn its application and limitations as well as its specific
potential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a
3-prong grounding type plug to fit the proper grounding type
receptacle. The green conductor in the cord is the grounding wire.
NEVER connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor
is clean and not slippery.
6. AVOID DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations or expose them to
rain. Keep work area well lit and provide adequate surrounding
work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper
speed.
SPECIFIC SAFETY RULES
Safety is a combination of common sense, staying alert and knowing
how your bandsaw works. Read and understand the following safety
rules before operating.
1) Adjust the upper guide to just clear workpiece.
2) Make sure that the blade is properly adjusted and tensioned before
operating.
3) Do not remove small jammed pieces until the blade has completely
stopped.
4) Hold workpiece firmly against the table.
5) Turn the machine off if the workpiece is to be backed out of an
uncompleted cut.
6) Do not operate this bandsaw using a dull or worn blade.
BEFORE EACH USE:
Inspect your bandsaw.
1) To reduce the risk of injury from accidental starting, turn the switch
off, unplug the bandsaw and remove the switch key before
changing the set-up, removing covers, guards or the blade.
2) Check the alignment of moving parts, binding of moving parts,
breakage of parts, bandsaw stability and any other conditions that
may affect the way the bandsaw works.
3) If any part is missing, bent or broken in any way, or if any electrical
parts do not work properly, turn the bandsaw off and unplug the
saw. Replace damaged or missing parts before using the bandsaw
again.
4) Make sure the blade teeth point downward, towards the table.
5) Make sure the blade guides are properly adjusted.
GENERAL & SPECIFIC
SAFETY RULES
10. USE RIGHT TOOL.
11. WEAR PROPER APPAREL.
12. ALWAYS WEAR SAFETY GLASSES.
13. MAINTAIN TOOL WITH CARE.
14. DISCONNECT TOOLS.
15. AVOID ACCIDENTAL STARTING.
16. CHECK DAMAGED PARTS.
17. NEVER LEAVE MACHINE RUNNING UNATTENDED.
6) Make sure the blade tension is properly adjusted.
7) To reduce the risk of accidental blade contact, minimize blade
8) Before starting your cut, watch the saw while it runs. If it makes an
9) Let the blade reach full speed before cutting.
TO REDUCE THE RISK OF INJURY FROM JAMS, SLIPS,
THROWN PIECES OR BROKEN BLADES
1) Use extra supports (tables, blocks, etc...) for any workpieces large
2) NEVER use another person as a substitute for a table extension, or
3) When cutting irregularly shaped workpieces, plan your work so it
4) Properly support round material such as dowel rods or tubing. They
5) Cut only one workpiece at a time. Caution: Never cut metals with
Don't force the tool or the attachment to do a job for which it was
not designed.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
footwear is recommended. Wear protective hair covering to
contain long hair. Roll up long sleeves above the elbows.
Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses
only have impact resistant lenses, thet are NOT safety glasses.
Also use a face or dust mask if cutting operation is dusty.
Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
Before servicing, when changing accessories or attachments.
Make sure the swich is in the ''OFF'' position before plugging in.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will
operate properly and perform their intended function. Check for
alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other
parts that are damaged should be properly repaired or replaced.
Turn power ''OFF''. Don't leave any tool running until it comes to a
complete stop.
breakage and provide maximum blade support, always adjust the
upper blade guide and blade guard to just clear the workpiece.
unfamiliar noise or vibrates a lot, stop immediately. Turn the saw off
and unplug. Do not restart until you have found and corrected the
problem.
enough to tip when not held down to the table top.
as additional support for a workpiece that is longer or wider than the
basic band saw table, or to help feed, support or pull the workpiece.
will not slip and pinch the blade. A piece of molding for example,
must lie flat or be held by a fixture or jig that will not let it twist, rock
or slip while being cut.
have a tendency to roll during a cut, causing the blade to "bite". To
avoid this, always use a "V" block or clamp the work to the miter
guage.
this band saw, only wood and wood products.