Output Settings; Headphone Settings; Power Control Triggers - McIntosh C12000 Controller Owner's Manual

Output Settings

Note: Output 1 (1-SS) uses Solid State amplification,
Output 2 (2-T) uses Tube amplification.
The Output Settings provide the ability to change
how the C12000 Output 1 and Output 2 function.
OUTPUT 1 and 2:
By defaut OUTPUT 1 and 2 are set to go On/Off by
using the Front Panel TRIM and ADJUST Controls
or the OUTPUT 1 and 2 Push-buttons on the Remote
Control. If it is desirable to have OUTPUT 1 and/or
2 always On regardless of the TRIM setting, perform
the following:
1. Press the SETUP Push-button to enter the SETUP
MODE. Refer to figure 2..
2. Rotate the TRIM Control until "SETUP: OUT-
PUT 1, Switched" appears on the Information Display.
Refer to figure 20.
SETUP: OUTPUT 1
Switched
Figure 20
3. Rotate the ADJUST Control until "SETUP:
OUTPUT 1, Unswitched" appears on the Information
Display. Refer to figure 21.
SETUP: OUTPUT 1
Unswitched
Figure 21
4. In a similar manner, perform steps 2 and 3 to
change the OUTPUT 2 setting. Refer to figures 22 and
23.
SETUP: OUTPUT 2
Switched
Figure 22
22
SETUP: OUTPUT 2
Unswitched
Figure 23
5. Exit the SETUP Mode by pressing the SETUP
Push-button.

Headphone Settings

The C12000 has the ability to automatically mute
the Output Jacks and/or Connectors when a Head-
phone Cable Plug is inserted into the C12000 Front
Panel HEADPHONES Jack. The Output Default Set-
tings are: MAIN - Unmuted
OUTPUT 1 - Muted
OUTPUT 2 - Muted
In the following examples the MAIN Output Jacks
will Mute and the OUTPUT 1 Connectors will not
Mute when Headphones are connected:
1. Press the SETUP Push-button to enter the SETUP
MODE. Refer to figure 2.
2. Rotate the TRIM Control until "SETUP: MUTE
WITH HDPH, Main = Unmuted " appears on the
Information Display. Refer to figure 24.
SETUP:MUTE WITH HDPH
Main = Unmuted
Figure 24
3. Rotate the ADJUST Control to change the current
setting to "SETUP: MUTE WITH HDPH, Main =
Muted". Refer to figure 25.
SETUP:MUTE WITH HDPH
Main = Muted
Figure 25
4. Rotate the INPUT Control to change the current
setting to "SETUP: MUTE WITH HDPH, Output 1 =
Muted". Refer to figure 26.
SETUP:MUTE WITH HDPH
Output 1 = Muted
Figure 26
5. Rotate the ADJUST Control to change the current
setting to "SETUP: MUTE WITH HDPH, Output
1 = Unmuted". Refer to figure 27.
SETUP:MUTE WITH HDPH
Output 1 = Unmuted
Figure 27
6. In a similar manner, perform steps 4 and 5 to
change the OUTPUT 2 setting. Refer to figures 28
and 29.
SETUP:MUTE WITH HDPH
Output 2 = Muted
Figure 28
SETUP:MUTE WITH HDPH
Output 2 = Unmuted
Figure 29
7. Exit the SETUP Mode by pressing the SETUP
Push-button.

Power Control Triggers

In the first example, the Power Control Triggers 1
and 2 will be assigned to Output 1 and 2 respectively:
1. Press the SETUP Push-button to enter the SETUP
MODE. Refer to figure 2..
2. Rotate the TRIM Control until SETUP:
TRIGGER 1, MAIN" appears on the Display. Refer to
figure 30.