Using The Stove; Firing; Modification Of Parameters; Extinguishing - Jøtul PC 900 Installation, Operation And Maintenance Manual

ENGLISH
11�3�2 Setting screen brightness
Screen brightness can be adjusted when the screen is in
standby mode.
a) Using keys , select the Configuration menu
press .
b) Select the item using button
"7"
button .
c) Using button , select submenu
button .
d) Set the desired brightness (
and , then confirm using button
11�3�3 Display settings
The objects that are displayed when the screen is in
standby mode can be configured.
Using the arrow keys
a) Using keys , select the Configuration menu
press .
b) Select the item using
"7"
button .
c) Using button , select submenu
the button.
d) Set one of the following parameters using buttons
and :
• The last visualisation performed by the client will
„ "
OFF
be displayed on the screen.
• All parameters can be displayed periodically.
„ "
1
• Temperature can be displayed (read by the
„ "
2
ambient temperature sensor).
• The current time can be displayed.
„ "
3
• The number of hours of autonomous work
before reloading of the pellet container can
„ "
4
be displayed, if the "refilling" function was
confirmed.
e) Press button , to confirm the setting.
11�3�4 Setting of the sound signallers volume
The sound signallers volume can be set as desired.
a) Using keys , select the Configuration menu
press .
b) Select the item using button
"7"
pressing button .
c) Using button , select submenu
the button.
d) Set the desired volume (
and , then confirm using button
11�3�5 Setting pellet type
The type of pellet used can be set.
24
and confirm by pressing
and confirm using the
[11]
, from to ) using buttons
OFF 1 5
.
, select the settings menu
button and confirm by pressing
and confirm using
[12]
and confirm by
and confirm using
[13]
) using buttons
OFF, od 1 do 5
.
a) Using keys
press .
b) Select the
"7"
button .
and
c) Using button
the button.
d) Set one of the following parameters using buttons
:
• Standard
„ "
1
• Medium pellet
„ "
2
• Coarse pellet
„ "
3
e) Press button

12 USING THE STOVE

;
12�1 FIRING
and
To fire up the stove, press the
seconds.
The flame icon will start flashing during the activation
phase, then it will be lit up constantly, indicating that the
stove has been fired up.
Automatic firing: the stove is equipped with an automatic
device that allows for ignition of pellet without the need
to use traditional lighter blocks or fluids�
Do not fire up the stove manually if the automatic
ignition device is damaged�
Upon first firing of the stove, unpleasant odours may be
emitted, as a result of evaporation or drying of certain
structural materials� These odours will disappear over
time�
It is recommended to ventilate rooms well during first
firings.
Do not leave the furnace door open in order to avoid a
situation in which the closing sensor detects the open
door and activates an acoustic alarm.
12�2 MODIFICATION OF PARAMETERS
It is possible to change the stove's operating parameters,
as described in section 10.3.
Settings remain unchanged until they are changed, even
after extinguishing or disconnection of the stove from the
power supply�
and
12�3 EXTINGUISHING
To extinguish the stove, press the
seconds; the flame icon will go dark.
To reignite the stove, it is recommended to wait until it
cools completely�
It is recommended to extinguish the stove according to
the above guidelines, and it must never be shut down by
disconnecting electrical power supply�
12�4 WORK WITH ROOM THERMOSTAT
If the stove is controlled by means of an external
thermostat (or chronothermostat), the fitter must
program configuration 2. In this configuration, the stove
will shut down when the external thermostat trips (open
circuit).
The stove will automatically reignite when the temperature
falls below the value set on the external thermostat
(closed circuit).
At first firing or after extinguishing of the stove by means
of the control panel (
using the control keyboard�
, select the Configuration menu
item using button and confirm by pressing
, select submenu and confirm using
[14]
, to confirm the setting.
button for several
button for several
button), it must be reignited
and
and