Stanley SDS-PLUS SHR263 Manual
Hide thumbs
Also See for SDS-PLUS SHR263:
- Manual (44 pages) ,
- Original instructions manual (33 pages) ,
- Instruction manual (25 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stanley SDS-PLUS SHR263
Summary of Contents for Stanley SDS-PLUS SHR263
- Page 1 English 简体中文 11 SHR263...
- Page 2 ENGLISH * The picture above may differ slightly to actual unit.
-
Page 3: Safty Instruction
Stay alert, watch what you are doing and use Fitting drill chuck (NQCC, Fig E) Your Stanley SHR263 SDS plus rotary hammer is intended driving set the operating mode selector (4) to the common sense when operating a power tool. Do... -
Page 4: Rotary Hammer Safety Warnings
ENGLISH Keep cutting tools sharp and clean. Properly main- Additional residual risks may arise when using the tool tained cutting tools with sharp cutting edges are less which may not be included in the enclosed safety warnings. likely to bind and are easier to control. These risks can arise from misuse, prolonged use etc. -
Page 5: Electrical Safety
Hertz Class II Construction ENGLISH ( Original Instructions) truction Watts Earthing Terminal ment or ENGLISH Rotary drilling: for screw driving and for drilling gauge according to the required depth. After that, tighten her than minutes Safety Alert Symbol the side handle. into steel, wood and plastics al may 4.00... - Page 6 clockwise. ♦ Set the depth stop (8) to the required position. The ENGLISH maximum drilling depth is equal to the distance between the tip of the drill bit and the front end of the depth stop. Œ switch (3). The tool speed depends on how far Turn the grip counter-clockwise until you can slide the ♦...
-
Page 7: Maintenance
♦ For hammer drilling in masonry and concrete, set the To replace the keyless chuck with the SDS Plus tool holder, (8), with t used. Stanley accessories are engineered to high quality Œ Fit the drill chuck assembly. WARNING! When the user leaves, or pick up, transport,... -
Page 8: Technical Data
After that, pull the switch for optimal as an option. WARNING! Since accessories, other than those be hazardous. To reduce the risk of injury, only Stanley, recom- product. in the hole would be cleared, and normal drilling can... - Page 9 Rotary drilling (Fig. B, Fig. D, Fig. C1/C2) switched off and unplugged. a. 保持警觉。操作电动工具时注意操作，保持清 本 Stanley SHR263 SDS plus 电钻专用于在混凝土、 ♦ For drilling in steel, wood and plastics, or for screw Fitting drill chuck (NQCC, Fig E) 醒。不要在疲倦，或受到药物、酒精或治疗的...
- Page 10 简体中文 ENGLISH ( Original Instructions) g. 在使用电动工具、附件以及工具刀头等时，请 接触旋转 / 运动部件时所导致的伤害风险。 g. Use the power tool, accessories and tool bits etc. ♦ Injuries caused when changing any parts, blades or 遵循这些说明并考量具体的工作条件以及要执 更换部件、锯片或配件时的伤害风险。 accessories. in accordance with these instructions, taking into 行的工作。将电动工具用于设计之外的操作时...
- Page 11 ENGLISH ( Original Instructions) gauge according to the required depth. After that, tighten Rotary drilling: for screw driving and for drilling 简体中文 the side handle. into steel, wood and plastics ♦ Slacken the side handle (9) by turning the grip counter- Hammer drilling: for concrete and masonry 日期码的位置（图...
- Page 12 简体中文 ENGLISH ( Original Instructions) 9. 侧手柄 通过逆时针转动手柄转松侧手柄 (9)。 gauge according to the required depth. After that, tighten 10. 日期码 将限深器 (8) 设置到所需位置。最大钻孔深度 the side handle. 11. SDS 钻头 相等于钻头尖端与深度尺前末端之间的距离。 ♦ Slacken the side handle (9) by turning the grip counter- clockwise.
- Page 13 2. Push the keyless chuck (12) onto the spindle and turn To replace the keyless chuck with the SDS Plus tool holder, used. Stanley accessories are engineered to high quality use for screw driver function, tighten screws Warning: Never use standard chucks in the 电动工具的性能取决于所使用的附件。Stanley 配...
- Page 14 Warning: Never use standard chucks in the gh quality accessory offered by Stanley, have not been tested with this the locking collar (5) to the locking position ♦ You may also use the drill chuck key to tighten the Optional Accessories...
- Page 16 N469703 11/2016...