CONTENTS 目錄 Clear Paper Jam 夾紙排解 ............................2 Document Feeder / 送稿裝置 ..........................2 Upper Left Door A 左上蓋 A ..........................3 Duplex Module 雙面列印組件 ........................... 4 Bottom Left Door B 左下蓋 B ..........................5 Bottom Left Door C 左上蓋 C ........................... 6 Standard Tray 標準紙盤...
夾紙排解 LEAR APER / 送稿裝置 1.1 D OCUMENT EEDER 1. 向上拉起自動送稿裝置左蓋把手,將左 1. Open the document feeder left cover 蓋完全打開。 until it stops. 2. 旋轉旋鈕以向上移除夾紙,並取出。 2. Turn the knob to transfer the jammed paper upward and remove it. 3. 確定原稿是否未撕破、起皺或摺疊,再 3. Make Sure that the orginal is not torn, 依照觸控式顯示面板中的指示重新方入...
A 左上蓋 A 1.2 U PPER 1. 提起蓋 A (1)的釋放杆,同時打開蓋 1. While lifting up the release lever of the (2)。 door A (1), open the door (2). 2. 如果紙張卡在熔著部組件外部,請取出 2. If paper is jammed outside the fusing 夾紙。 unit, remove the jammed paper. 3.
雙面列印組件 1.3 D UPLEX ODULE 1. 沿箭頭方向拉下控制杆 A1,然後打開 1. Gently open the bottom left door while 熔著部組件蓋。 pulling the release lever. 2. 提起控制杆 A2,取出夾紙,然後將控 2. Lift up the lever A2, remove the 制杆 A2 恢復原位。 jammed paper, and return the lever A2. Page 4 of 9...
B 左下蓋 B 1.4 B OTTOM 1. 沿箭頭方向拉下控制杆 A1,然後打開 1. Gently open the bottom left door while 熔著部組件蓋。 pulling the release lever. 2. 取出夾紙。 2. Remove the jammed paper. Page 5 of 9...
C 左上蓋 C 1.5 B OTTOM 1. 提起蓋 A (1)的釋放杆,同時打開蓋 1. While lifting up the release lever of the (2)。 door A (1), open the door (2). 2. 提起拉桿時,打開上部的蓋 C。 2. While lifting up the release lever, open the door C at the top part. Page 6 of 9...
標準紙盤 1.6 S TANDARD 1. 將發生卡紙的紙盤完全拉出。 1. Pull out the paper tray where the paper jam occurred until it stops. 2. 清除卡紙的紙張。 2. Remove the jammed paper. 3. 推入紙盤。 3. Push in the paper tray. 手送紙盤 1.7 B YPASS 1. 清除卡紙的紙張。 1.
更換碳粉匣 EPLACING ONER 先確定裝置已經停止運作,然後開啟前蓋。 1. Confirm that the machine is not operating, and open the front cover. 慢慢拉出碳粉卡匣。 2. Pull out the toner cartridge slowly. 輕輕搖晃新碳粉卡匣。 3. Shake the new toner cartridge gently. 把碳粉卡匣的箭咀標誌向上,然後慢慢地 4. Hold the cartridge with the arrow facing 插入卡匣。...
更換碳粉回收匣 EPLACING ASTE ONER ONTAINER 先確定裝置已經停止運作,然後開啟前 1. Make sure that the device is not operating, and open the front door. 蓋。 2. Take out the waste toner container from the device. 把碳粉回收匣從裝置中取出。 3. Put the new waste toner container into 把新的碳粉回收匣正確地裝回裝置內。...
Page 11
2513-2513 This document includes Fuji Xerox product(s), licensed from Xerox Corporation. The distributor of the product(s) is FUJIFILM Business Innovation Corp. Xerox, Xerox and Design, as well as Fuji Xerox and Design are registered trademarks or trademarks of Xerox Corporation in Japan and/or other countries.