Table of Contents
Related Manuals for Autopage RS-750lcd
Summary of Contents for Autopage RS-750lcd
- Page 1 http://www.msvmaster.lv SVMASTER - PROFESSIONAL REMOTE STARTER WITH ALARM SYSTEM 2-WAY LCD COMMUNICATION INSTALIATION MANUAL THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY http://www.msvmaster.lv SVMASTER -...
- Page 2 http://www.msvmaster.lv SVMASTER - http://www.msvmaster.lv SVMASTER -...
-
Page 3: H2 5 Pin Wire Harness
http://www.msvmaster.lv SVMASTER - PIN HEAVY GAUGE WIRE HARNESS Fuse 2. Red: Fuse 5. Pink: 6. Brown: ACCiHeater Output 5 PIN WIRE HARNESS 4. Brown Wire: P o s m ~ e O U I ~ U I T O Siren or 3 A Fuse Horn (Programmable) Constant Battery Source... - Page 4 8 PIN BLACK CONNECTOR FOR INPUT CONNECTION: http://www.msvmaster.lv SVMASTER - Wire: Negative Safety Shut Down input for Hood pin 1. Whitelalack Wire: Neutral Safety Switch Input 2. B l a c W h i t e Remote Start Toqqle Switch Input Wire: Positive Safety Shut Down input for Brake switch.
-
Page 5: H1: 6 Pin Heavy Gauge Wiring Connection
http://www.msvmaster.lv SVMASTER - WIRING CONNECTIONS Remember: The function of this system when starting a vehicle is to duplicate the functions of the ignition key. Below, we will explain the three basic functions of the ignition switch. Since this installation will require analysis of the ignition switch functions, we recommend making the three connections below at the ignition switch harness directly. - Page 6 http://www.msvmaster.lv SVMASTER - PINK Wire Ignition Output Some vehicles have [2] ignition wires that must be powered. Connect the PINK wire to the ignition 2 wire from the ignition switch. The ignition wire should receive “12 volts” when the ignition key is in the “ON” or “RUN” and “START’ or “CRANK position. When the ignition is turned “OFF”, the ignition wire should receive “0”...
- Page 7 http://www.msvmaster.lv SVMASTER - H3.2 PIN WHITE CONNECTOR FOR THE LED STATUS INDICATOR: The led indicator status should be mounted in a highly visible area such as top of the dashboard, on top of the shifter console or on dashboard face. Leave at least 6mm space behind the mounting location for LED housing.
-
Page 8: Start Input
http://www.msvmaster.lv SVMASTER - An optional “remote start toggle switch” can be added to temporarily disable the Remote Start Device, it can prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the OFF position. - Page 9 http://www.msvmaster.lv SVMASTER - (-)Wait Start Wire Wait to Start Wait Start ..NEGATIVE DOOR SWITCH SENSING INPUT This wire is the ground trigger input wire for negative door pin switch. This wire is connection for "grounding" type factory door pins locate the "common wire" that connects the door pin switches.
- Page 10 http://www.msvmaster.lv SVMASTER - H8.4-PIN ORANGE CONNECTOR FOR SIS-11 SHOCK SENSOR: ORANGE PLUG ADJUST OPEIIING The SIS-11 may be mounted to any flat surface or may be wire-tied to any under-dash wire harness. Do not mount he SIS-11 under the engine hood. The 515-11 is not waterproof. The DO NOT MOUNT THE SIS-11 UPSIDE DOWN.
- Page 11 http://www.msvmaster.lv SVMASTER - Cut (#1) wire (as shown), and connect the ignition switch side of the cut wire to terminal Connect the previously selseced resistor from terminal #87 to the second(#2) wire (as shown). YELLOW wire wire Ignition (-) 200ma CHANNEL 2 Programmable Output This will become a 1 second pulse ground by activate channel 2 on transmitter for two seconds, the current capacity of this wire is 200 mA.
- Page 12 http://www.msvmaster.lv SVMASTER - Violet wire Yellow wire to Oranqe wire Ignition Switch from control module "Start" White wire current ground output from the vehicle's horn switch. When the system is triggered, the horn will Or Ground sound. H10.3 PIN GREEN CONNECTOR TEMPERATURE SENSOR The Temperature Sensor should be installed inside the vehicle.
-
Page 13: Door Locks
http://www.msvmaster.lv SVMASTER - H7.3 PIN DOOR LOCK CONNECTOR: NEGATIVE TRIGGER DOOR LOCK SYSTEM Blue Wire Dwr Unlock ) Unlock Pulse Green D w r Lock Wire ) Unlock Pulse POSITIVE TRIGGER DOOR LOCK SYSTEM DOOR LOCK 5-WIRE ALTERNATING Blue Wire Door lock Locking Master Switch... - Page 14 http://www.msvmaster.lv SVMASTER - PROGRAMMING PROGRAMMING XT-75s REMOTE TRANSMllTER Note: This mode will only retain the last 4 remote transmitters programmed If the transmitter memory is exceeded, the security system will start deleting transmitters from memory m chronological order Important Note: This program mode is for XT-75s remote transmitter programming only; do not program the XT75LCD two-way transmitter on this mode.
- Page 15 http://www.msvmaster.lv SVMASTER - Note: A Maximum of (2) two-way LCD screen remote transmitters can be programmed. FEATURE PROGRAMMING ALARM FEATURE “I” PRORAMMING: Turn the Ignition ‘switch ‘ON/OFF 3 TIMES and stay in OFF position. Push the Valet switch 2 times holding in on the 2”d push until 1 short & 1 long chirp is heard. Then release the valet switch.
- Page 16 http://www.msvmaster.lv SVMASTER - Door Ajar Error Chirp This feature controls the error chirp that is generated if the system is armed with the door trigger active. This useful in vehicles that have a long dome light delay after the door has been closed. off, If the system is armed before the dome light has turned the security system will generate the...
-
Page 17: Password Pin Code Setup
http://www.msvmaster.lv SVMASTER - ALARM FEATURE “111” PRORAMMING: 2. Push the Valet switch 6 times holding in on the 6Ih push until short & 1 long chirp is heard the valet switch. You are now in the Alarm feature ‘111’ proqrammina mode. Then relea: 3. - Page 18 http://www.msvmaster.lv SVMASTER - Delete Password Pin Codeloverride Without Password Pin Code (Factory default setting): Within 15 seconds, press and hold the transmitter button for 4 seconds. A one long chirps to confirm Deleted the Password Pin Code. Example: To program the Password Code 92, you would; Enter: 1.
-
Page 19: Tachometer Checking Type
http://www.msvmaster.lv SVMASTER - START FEATURE “11” PRORAMMING: 2. Push the Valet switch 10 times holding in on the push until 5 short & 1 long chirp is heard. Then release the valet switch. You are in the Remote Start feature ‘11’ program mode. 3. - Page 20 http://www.msvmaster.lv SVMASTER - If the crank time is too long, (Engine already successfully running, while still cranks): a. Press the button on the transmitter to stop engine running. button on the transmitter to set proper “Check Level to Low position. Press [2] LED flash, [2] chirps to confirm this setting b.
- Page 21 http://www.msvmaster.lv SVMASTER - Select “Checking Type”: Press the transmitter button to set the “Timer Checking Type”. LED flash, chirps to confirm this setting Once you complete step 3, you can adjust and test “Start Timer” as below: START TIMER PROGRAMMING: (TEST and ADJUST) While the system stay in Start Feature “II”...
-
Page 22: Shutdown Diagnostics
http://www.msvmaster.lv SVMASTER - SHUTDOWN DIAGNOSTICS The unit has the ability to report the cause of the last shutdown of the remote start system. Enter: Turn the Ignition ‘switch to ‘ON position. Press the button on the transmitter. The LED will now report the last system shutdown by flashing one minute in the Shutdown Mode Flashes... -
Page 23: Neutral Start Safety Test
http://www.msvmaster.lv SVMASTER - NEUTRAL START SAFETY TEST: 2. Block the drive wheels to prevent vehicle movement. Sitting in the vehicle, turn the ignition switch to “ON” or “RUN” position. But do not start the engine. 4. Step on the brake pedal and shift the gear selector into “DRIVE (D). 5.