Bostitch BCN662 Instruction Manual page 5

into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c ) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
6) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety Rules for Finish Nailer
Always assume that the tool contains fasteners.
•
Careless handling of the nailer can result in unexpected
firing of fasteners and personal injury.
• Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge a fastener
causing an injury.
Do not actuate the tool unless the tool is placed
•
firmly against the workpiece. If the tool is not in
contact with the workpiece, the fastener may be deflected
away from your target.
• Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the nailer may be accidentally activated if it is
plugged in.
• Do not use this nailer for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
• Use caution while removing a jammed fastener. The
mechanism may be under compression and the fastener
may be forcefully discharged while attempting to free a
jammed condition.
• Hold tool by insulated gripping surfaces when
performing an operation where driven fasteners
may contact hidden wiring. Contact with a "live" wire
will make exposed metal parts of the tool "live" and shock
the operator.
Additional Nailer Safety Warnings
Always wear safety glasses.
•
Always wear ear protection.
•
• Only use fasteners of th e type specified in
the manual.
• Do not use any stands for mounting the tool
to a support.
• Do not disassemble or block any parts of the
fastener driving tool such as the contact trip.
Prior to each operation check that the safety
•
and triggering mechanism is functioning properly
and that all nuts and bolts are tight.
• Do not use the tool as a hammer.
• Do not use the BTCN120
ʵ when changing from one driving location to another
involving the use of scaffoldings, stairs, ladders or
ladder-like constructions, e.g., roof laths, etc.;
ʵ when closing boxes or crates;
ʵ when fitting transportation safety systems, e.g., on
vehicles, wagons, etc.
For exemptions check your local national
workplace regulations.
• Always check local workplace regulations.
Never point any operational fastener driving tool at
•
yourself or at any other person.
• While working, hold the tool in such a way that no
injuries can be caused to the head or to the body
in the event of a possible recoil due to a disruption
in the energy supply or hard areas within the work
piece.
Never actuate the fastener driving tool into
•
free space.
• In the work area, carry the tool at the workplace
using only one handle, and never with the
trigger actuated.
• Consider the conditions in the work area Fasteners
can penetrate thin work pieces or slip off corners
and edges of the work piece, and thus put people
at risk.
• Do not drive fasteners close to the edge of the
work piece.
• Do not drive fasteners on top of other fasteners.
Sequential/Bump Selector Switch
Sequential Action
• When using the tool in sequential mode mode, do
not actuate the tool unless the tool is placed firmly
against the workpiece.
Bump Action
• When using the tool in bump action, be careful of
unin tentional double fires resulting from tool recoil.
Unwanted fasteners may be driven if the contact trip is
allowed to accidentally re-contact the work surface.
• To Avoid Double Fires:
ʵ Do not engage the tool against the work surface with
a strong force.
English
3