Programming Wireless Keypad - Genie 1035 Operation & Maintenance Manual

Tip: Program Keypad before mounting.
Keypad Overview:
Program Key
LED
Keypad
Up/Down Key
(enter)
Keypad O
Activate keypad by opening battery
tab. Reinstall compartment door to
STEP 1) PROGRAMMING A PIN NUMBER
Program the keypad for the rst time* with a Personal
Identi cation Number (PIN). This PIN must be 3 to 8 digits.
1. Ensure number pad back lighting is o .
2. Press 3-5-7 in sequence.
3. Press PROGRAM key. LED will blink once per second.
4. Enter a PIN number (3-8 digits).
5. Press PROGRAM key. LED will blink twice and shut o .
• The keypad is now programmed with a PIN number and
ready to program to Genie® Intellicode® garage door
opener(s).
• See STEP 2A to program 1 Genie® Opener.
• See STEP 2B PROGRAMMING FOR MULTIPLE OPENERS if
using keypad to operate up to 3 doors.
• If LED did not blink twice and shut o , please see
RESETTING THE KEYPAD (FACTORY DEFAULT) section.
STEP 2A) PROGRAMMING THE KEYPAD TO 1 OPENER
1. Place garage door opener into PROGRAMMING MODE.
2. Ensure number pad back lighting is o .
3. Enter the PIN number on keypad.
4. Press the UP/DOWN key 3 to 4 times slowly until garage
door opener operates.
• This completes the programming of a single door. See
STEP 3 SINGLE DOOR OPERATION for further instruction.
22
WIRELESS KEYPAD PROGRAMMING
LED Flashing
Keypad On Keypad Flashing
compartment and pull protective
begin programming.
TAB
STEP 2B) PROGRAMMING THE KEYPAD FOR MULTIPLE OPENERS
(UP TO 3)
Program the keypad with a Personal Identi cation Number
(PIN) as described in step 1. Then follow these additional steps.
1. Ensure number pad back lighting is o .
2. Enter PIN as programmed in STEP 1.
LED O
3. Press PROGRAM key twice. LED will blink once per second.
4. Enter total number of openers that keypad will be
operating. (2 or 3).
LED On
5. Press PROGRAM key once. LED will blink twice and shut o .
• NOTE: Only one PIN number can be used.
• The keypad is now programmed with a PIN number and
set up for multi opener operation. Keypad is now ready to
program to multiple Genie® Intellicode® garage door openers.
• If LED did not blink twice and shut o , please see RESETTING
THE KEYPAD (FACTORY DEFAULT) section.
PROGRAMMING THE KEYPAD TO MULTIPLE OPENERS
1. Place desired garage door opener (1, 2, or 3) into
PROGRAMMING MODE as illustrated in the section below.
2. Ensure number pad back lighting is o .
3. Enter the PIN number on keypad.
4. Press the UP/DOWN key once.
5. Press the number of the desired door (1,2 or 3).
6. Press the UP/DOWN key 3-4 times slowly until garage door
opener operates.
• Repeat steps 1 through 6 to program second and third
openers.
• This completes programming of multiple doors. See STEP 3
MULTI-DOOR OPERATION for further instruction.
PUTTING OPENER INTO PROGRAMMING MODE:
1. Press and hold the program button until the round LED
turns blue, then release.
2. The round LED will go out and the long LED will begin
ashing purple.
3. Return to STEP 2A or 2B.
NOTE: The openers LEARN LED will time out in 30 seconds.
Programming must be completed within 30 seconds.
* RESETTING THE KEYPAD (FACTORY DEFAULT):
If the keypad has already been programmed or at any time the
programming should be erased and started from the factory
default, follow these steps.
1. Ensure that number pad back lighting is o .
2. Press and hold the PROGRAM and UP/DOWN Keys
together for approximately 5 seconds.
3. The LED will ash twice and all lights will go out indicating
the keypad has been reset.
4. Start at STEP 1 to program a new PIN number.
Solid Blue
Flashing Purple
(UP TO 3)
PRESS
&
RELEASE