Advertisement
Quick Links
CS-5601
4 WINDOW CONTROL MODULE
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION:
CONGRATULATIONS on your choice of a 4 Window Control Module by Crimestopper Security Products Inc.
This booklet contains the information necessary for installing, and operating your system. If any questions
arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number
below.
*IMPORTANT INFORMATION:
This system does not affect the operation of the factory power window switches. This is an ADD-ON
module to an Alarm, Remote Start, or Keyless Entry system. It is designed for medium to high current
window motors. It can roll 4 windows UP or DOWN, or 2 windows UP and DOWN. Each window circuit
activates in sequence, one at a time. This minimizes the current draw on the vehicle battery.
This installation book is designed for the installer or individual with an existing understanding of automotive
electrical systems, along with the ability to test and connect wires for proper operation. To ease installation,
we suggest that you READ THIS MANUAL before beginning your installation. The information contained in
this manual is provided as a GENERAL GUIDLINE and it may differ from your vehicle! If you are not confident
with performing the installation steps as required by this system, we suggest seeking professional installation.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
REV - 9/3/2004
Advertisement
Related Manuals for CrimeStopper CS-5601
Summary of Contents for CrimeStopper CS-5601
- Page 1 INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION: CONGRATULATIONS on your choice of a 4 Window Control Module by Crimestopper Security Products Inc. This booklet contains the information necessary for installing, and operating your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.
-
Page 2: Pre-Installation Considerations
Pre-Installation & Component Mounting………………..…….……………………………………………2-3 Wiring …………..………………………………………………………………………………………….…….3-4 4 Windows UP.…..………………………………………….……………….………..……………….…..……..5 2 Windows UP and DOWN..………………….…………………………………………………………………6 Vehicles with Normally Open Power windows……………..………….……………………………………7 Testing and Adjusting Window Shut Off Current…………………..………………………………………8 PRE-INSTALLATION CONSIDERATIONS To ease installation, we suggest that you READ THIS MANUAL before beginning your installation. BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY). -
Page 3: Component Mounting
8 - PINK: Connect to an ignition wire that shows +12 Volts when the key in both “On” and “Start” positions. This wire prevents the module from activating the windows while driving the vehicle. COMPONENT MOUNTING Don’t Install CS-5601 Module inside vehicle door WIRING – Small Wires... - Page 4 2 JUMPER LOOPS LOOP 1: Circuit #1 and #2 CUT: Constant or Latched (starter kill), Trigger for window circuit #1 and #2. CONNECTED: Momentary Pulse (2 LOOP 2: Circuit #3 and #4 CUT: Constant or Latched (starter kill), Trigger for window circuit #3 and #4. CONNECTED: Momentary Pulse (2 9 Position Connector Plug –...
- Page 5 Left Front Circuit #1 Right Front Circuit #2 Left Rear Circuit #3 Right Rear Circuit #4...
- Page 6 Circuit #1 and #2 is used to roll widows up. Circuit #3 and #4 is used to roll windows down. Circuit #1 Circuit #3 Circuit #2 Circuit #4...
- Page 7 Circuit #1 **NOTE** See page 3 for 8 Pin Plug Wiring This diagram is used on vehicles with window circuits that: 1. Switch ground to roll the windows up or down. 2. Switch both power and ground to roll the windows up or down. 3.
- Page 8 Rear Access Door Turn clockwise to increase High Current shut off limit. www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2003 Crimestopper Security Products Window Circuit #1 and #2 Min = 10 Amps Max = 30 Amps ONLINE TECHNICAL SUPPORT...