Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crestron TPS-IMW
Summary of Contents for Crestron TPS-IMW
- Page 1 Crestron TPS-IMW Wall Mounted Interface Module Operations Guide...
- Page 2 This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2004 Crestron Electronics, Inc.
-
Page 3: Table Of Contents
Crestron TPS-IMW Contents Wall-Mounted Interface Module: TPS-IMW Introduction...1 Features & Functions...1 Specifications...1 Physical Description ...2 Industry Compliance...6 Setup...6 Network Wiring ...6 Hardware Hookup...8 Problem Solving...12 Troubleshooting...12 Further Inquiries ...14 Future Updates...14 Return and Warranty Policies ...15 Merchandise Returns / Repair Service ...15 CRESTRON Limited Warranty ...15... -
Page 5: Wall-Mounted Interface Module: Tps-Imw
TPS-IMW Introduction Features & Functions The TPS-IMW is designed to serve as an optional interface module for the Crestron TPS-3000, TPS-4000, TPS-5000 and TPS-6000 tilt touchpanels. The module provides a clean, 2-gang mountable interface for direct connection to the touchpanel. The TPS-IMW creatively hides most of the connections behind a wall. -
Page 6: Physical Description
Wall-Mounted Interface Module Physical Description The TPS-IMW, shown in the following diagram, mounts into a 2-gang electrical box (recommended 2.5" depth). The back of the unit is labeled and provides a network connector, video input connector, audio input, and microphone output. Once installed, there are only two RJ-45 connectors (for audio/network/video) visible that provide connections to the touchpanel via the cables supplied with the touchpanel. - Page 7 Crestron TPS-IMW Ports There are six ports that serve various functions on the TPS-IMW. Refer to the following diagrams and descriptions of each port. NTSC/PAL VIDEO The NTSC/PAL video input uses a 6-position mini-terminal block connector for twisted pair wiring of balanced or unbalanced video signals.
- Page 8 TPS-5000, or TPS-6000 touchpanel. Refer to the descriptions and pinout table that follow this paragraph. The 10-pin net/video cable assembly to connect the touchpanel to the TPS-IMW is supplied. Even though the 8-pin audio cable may fit into the port, do not use it.
- Page 9 The copper connector on the far left is pin 1. CAUTION: The 10-pin RJ-45 net/video connector cable supplied by Crestron is a custom cable and is the only one that should be used. The end of the cable has a metal shield that is required to protect the equipment.
-
Page 10: Industry Compliance
The copper connector on the far left is pin 1. Industry Compliance As of the date of manufacture, the TPS-IMW has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. - Page 11 Cresnet power usage of each network unit to be daisy-chained must be added together to determine the Cresnet power usage of the entire chain. If the unit is a home-run from a Crestron system power supply network port, the Cresnet power usage of that unit is the Cresnet power usage of the entire run.
-
Page 12: Hardware Hookup
Hardware Hookup Connections to the Back of the TPS-IMW The TPS-IMW serves as interface between the touchpanel and the Cresnet system. Refer to the illustration after this paragraph for proper connections; apply power last. When making network connections to a control system or Cresnet peripherals, refer to “Network Wiring”... - Page 13 A video source can be connected to a TPS-3000, TPS-4000, or a TPS-VID1/2 installed in a TPS-5000 or TPS-6000 touchpanel. The TPS-IMW allows for the connection of balanced or unbalanced video signals using twisted pair cable. Refer to the following diagrams to connect balanced or unbalanced video signals.
- Page 14 #6-32 flat-head slotted screws (supplied). Installation of the TPS-IMW Once the TPS-IMW is installed into a 2-gang electrical box, it can be covered with a Decora wallplate (purchased separately). Remove the backing from the tape on the back of the two silk-screened insert plates (supplied).
- Page 15 (10-pin) and audio (eight-pin) cables. NOTE: The included AUDIO cable has a connector with a blue cover to match the blue lettering on the TPS-IMW. As older AUDIO cables may not have the blue cover, be sure to insert the AUDIO cable into the AUDIO port.
-
Page 16: Problem Solving
Wall-Mounted Interface Module Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPS-IMW Troubleshooting TROUBLE Touchpanel does not function. No power to touchpanel. Video... - Page 17 Inspect connector pins. If bent, connector pins. carefully re-straighten. If broken, contact Crestron customer service. Touchpanel is set Switch to “composite” video. to auto-detect or S- video when two composite signals are plugged into the TPS-IMW. Wall-Mounted Interface Module: TPS-IMW • 13...
-
Page 18: Further Inquiries
Crestron website (www.crestron.com) for a listing of Crestron worldwide offices. You can also log onto the online help section of the Crestron website (www.crestron.com) to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. -
Page 19: Return And Warranty Policies
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any application other than that for which it was intended, or if it has been subjected to misuse, accidental damage, modification, or improper installation procedures. - Page 20 Crestron Electronics, Inc. Operations Guide – DOC. 5857A 15 Volvo Drive Rockleigh, NJ 07647 11.04 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.