Table of Contents
Advertisement
Available languages
Available languages
8. CLEANING AND MAINTENANCE
• Before carrying out any maintenance work on the hob, allow it
to cool down.
• Only products, (creams and scrapers) specifically designed for
glass ceramic surfaces should be used. They are obtainable
from hardware stores.
• Avoid spillages, as anything which falls on to the hob surface
will quickly burn and will make cleaning more difficult.
• It is advisable to keep away from the hob all substances which
are liable to melt, such as plastic items, sugar, or sugar-based
products.
MAINTENANCE:
- Place a few drops of the specialised cleaning product on the
hob surface.
- Rub any stubborn stains with a soft cloth or with slightly damp
kitchen paper.
- Wipe with a soft cloth or dry kitchen paper until the surface is
clean.
If there are still some stubborn stains:
- Place a few more drops of specialised cleaning fluid on the
surface.
- Scrape with a scraper, holding it at an angle of 30° to the hob,
until the stains disappear.
- Wipe with a soft cloth or dry kitchen paper until the surface is
clean.
- Repeat the operation if necessary.
A FEW HINTS:
Frequent cleaning leaves a protective layer which is essential to
prevent scratches and wear. Make sure that the surface is clean
before using the hob again. To remove marks left by water, use
a few drops of white vinegar or lemon juice. Then wipe with
absorbent paper and a few drops of specialised cleaning fluid.
The glass ceramic surface will withstand scraping from flat-
bottomed cooking vessels, however, it is always better to lift them
when moving them from one zone to another.
NB:
Do not use a sponge which is too wet.
Never use a knife or a screwdriver.
A scraper with a razor blade will not damage the surface,
as long as it is kept at an angle of 30°.
Never leave a scraper with a razor blade within the reach
of children.
Never use abrasive products or scouring powders.
Steam cleaners are not suitable for use.
• The metal surround : to safely clean the metal surround wash
with soap and water, rinse, then dry with a soft cloth.
9. PROBLEM SOLVING
The cooking zones do not simmer or only fry gently
• Only use flat-bottomed pans. If light is visible between the pan
and the hob, the zone is not transmitting heat correctly.
• The pan bottom should fully cover the diameter of the selected
zone.
The cooking is too slow
• Unsuitable pans are being used. Only use flatbottomed
utensils, that are heavy and have a diameter at least the same
as the cooking zone.
Small scratches or abrasions on the hob's glass surface
• Incorrect cleaning or rough-bottomed pans are used; particles
like grains of sand or salt get between the hob and the bottom
of the pan. Refer to the "CLEANING" section; make sure that
pan bottoms are clean before use and only use smooth bottomed
pans. Scratches can be lessened only the cleaning is done
correctly.
Metal marks
• Do not slide aluminium pans on the hob. Refer to the cleaning
recommendations.
• You use the correct materials, but the stains persist.
Use a razor blade and follow the "CLEANING" section.
Dark stains
• Use a razor blade and follow the "CLEANING" section.
Light surfaces on the hob
• Marks from an aluminium or copper pan, but also mineral, water
or food deposits; they can be removed using the cream cleaner.
Caramelisation or melted plastic on the hob.
• Refer to the "CLEANING" section.
The hob does not operate or certain zones don't work
• The shunts are not positioned correctly on the terminal board.
Have a check made that the connection is done in compliance
with the recommendations.
• Hobs with sensitive controls: a big spill or object covers at
least two buttons, for at least 10 seconds. Clean up the spill or
remove the object.
• The control panel is locked. Unlock the hob.
The hob does not cut off.
• The control panel is locked. Unlock the hob.
The hob stops automatically
• A spill covers at least two buttons for more than 10 seconds; the
hob switches to safety, and an audible beep sounds. Clean up
the spill or remove the object.
• The cooking zones stop automatically if they are left on for too
long. Refer to the section, "operating time".
Frequency of on/off operations for cooking zones
• The on-off cycles vary according to the required heat level:
- low level: short operating time,
- high level: long operating time.
"H" display, residual heat indicator, blinking.
• The electronic temperature is too high. A technician should verify
the fitting in compliance with the recommendations.
PROBLEM SOLVING
10. AFTERCARE
Before calling out a Service Engineer please check the
following:
— that the plug is correctly inserted and fused;
If the fault cannot be identified switch off the appliance — do not
tamper with it — call the Aftercare Service Centre. The appliance
30° Maxi
is supplied with a guarantee certificate that ensures that it will be
repaired free of charge at the Service Centre.
11. PROTECTION OF THE ENVIRONMENT
9 GB-IE
This appliance is marked according to the
European directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE).
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components (which can
be re-used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials.
Individuals can play an important role in ensuring that WEEE does
not become an environmental issue; it is essential to follow some
basic rules:
• WEEE shall not be treated as household waste.
• WEEE shall be handed over to the relevant collection points
managed by the municipality or by registered companies. In many
countries, for large WEEE, home collection could be present.
• When you buy a new appliance, the old one may be returned to
the retailer who has to collect it free of charge on a one-to-one
basis, as long as the equipment is of equivalent type and has the
same functions as the supplied equipment.
Advertisement
Table of Contents
