Related Manuals for Chauvet DVM-HR
Summary of Contents for Chauvet DVM-HR
- Page 1 DVM-HR DV Wall™ USER MANUAL CHAUVET, 3000 N 29 Ct, Hollywood, FL 33020 U.S.A (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.com 2007-02-05 16:45...
-
Page 2: Table Of Contents
©CHAUVET, 2006, All Rights Reserved Information and specifications in this User Manual are subject to change without notice. CHAUVET assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. DV Wall System User Manual... -
Page 3: Before You Begin
World Wide Web DV Wall System User Manual Save the carton and all packing If you should require sending any items back to CHAUVET, call CHAUVET for a Note: (RMA) Return Merchandise Authorization number. The factory will not allow any shipments without an RMA. -
Page 4: Important Safety Information
If you have any questions about how to operate the fixture safely, please contact CHAUVET. P r o t e c t i o n a g a i n s t E l e c t r i c S h o c k •... -
Page 5: Introduction
2. Introduction Overview The DV Wall is both an indoor and outdoor LED video wall display suitable for a wide range of applications. An IP65 rating ensures reliable and safe operation in most weather conditions. The DV Wall can be seen comfortably during daytime or night time hours. The DV Wall’s modular rugged design provides the user many shape and size building options. -
Page 6: Product Overview
Product Overview DV Wall System User Manual DV Wall System User Manual 1 Panel 1 Panel DV Wall 1024 Panel DV Wall 1024 Panel Resolution: 16 vertical lines/columns Resolution: 16 vertical lines/columns 4 square panels = 1 square meter 4 square panels = 1 square meter Introduction Introduction Horizontal width:... -
Page 7: Hardware Setup
3. Hardware Setup AC Power Warning! Verify that the power requirement label on your unit matches the line voltage applied. All fixtures must be connected to circuits with a suitable Earth Ground. • To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart. -
Page 8: Maximum System Configuration
Maximum System Configuration 3 meters 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Gaps between matrix sections are for visual aid only. Panel sections pair up edge to edge to maintain consistent pixel separation across multiple matrix sections. Other Configuration Examples 1 2 3 4 5 6 7 8 9 10 11 12... -
Page 9: Mounting System
Setup Mounting System Each DV Wall panel comes with a square bracket with interlocking connectors that must first be bolted to the two tracks located on opposite sides of the back of the panel using the provided M10 Hex bolts. Affix the square bracket to the back of the DV Wall panel... -
Page 10: Flying Bracket Attachment
Flying bracket attachment The flying bracket attachment is used to fly or rig a 1 meter width section of a DV wall. It is designed to be attached to the very top row of a 1 meter section. Additional hardware is provided for interconnecting multiple flying brackets. -
Page 11: Signal & Power Configuration
Signal & Power Configuration DISPLAY CARD DISPLAY CARD TRANSMITTER TRANSMITTER AC: 110V/ 230V...50/ 60Hz AC: 110V/ 230V...50/ 60Hz No more than 20 panels should be No more than 20 panels should be connected to a 20 amp circuit on connected to a 20 amp circuit on 110V power or 40 panels on 230V. -
Page 12: Dv-Wall Driver
DV-Wall Driver Every driver contains 16 output ports (J1 ~ J16). Each output port provides signal source to one horizontal row of panels not exceeding 6 panels wide. Example If an application called for a video wall 3 meters high and 3 meters wide the following connection diagram would apply: J16 J15 J14... -
Page 13: Dipswitch Settings
Dipswitch Settings A DV-Wall video display matrix may consist of up to 16 drivers or 16 individual grid sections in various pattern configurations. Each driver must be addressed according to your configuration so that the video displayed appears whole and intact. Two internal dipswitches (JP1 & JP2) are addressed according to your system layout and configuration. -
Page 14: Jp2 Dipswitch
JP2 Dipswitch In order for video to display properly across multiple sections or drivers, each driver must be addressed accordingly. The JP2 dipswitch establishes the horizontal starting address or (vertical line) for each section of matrix. Vertical Line, JP2 set @ 0 (default) (horizontal starting address) Horizontal Line Just like the JP1 dipswitch, JP2 has different numerical designations for addressing. -
Page 15: Transmitter Card
Transmitter Card Install the transmitter card in an available PCI slot in your computer. The transmitter card is the interface between your PC, DV-Wall Studio software and the DV-Wall Screen. You must use the DVI cable provided to connect from the computers DVI output to the DVI port on the transmitter card. DVI Port Data Out 1 &... -
Page 16: Example System Configurations
Example System Configurations 4:3 Aspect Ratio 4 meters by 3 meter Front View System Information Vertical lines: 128 Horizontal lines: 96 Resolution: 128 x 96 pix Size: 4m x 3m Panels: 48 (8 x 6) Power: 3 x 20A (110V) Drivers: 2 Ethernet Out: Out 1 J Ports: 1 ~ 6... -
Page 17: Meters By 12 Meters
16 meters by 12 meters Width 96 pixels/lines Driver 6 Net OUT1 outputs lines 0 ~ 256 Net OUT2 outputs lines 257 ~ 512 System Information Vertical lines: 512 Horizontal lines: 384 Resolution: 512 x 384 pix Driver 12 Size: 16m x 12m Panels: 768 (32 x 24) Power: 39 x 20A (110V) Starting... -
Page 18: 16:9 Aspect Ratio
16:9 Aspect Ratio 8 meters by 4.5 meters Front View System Information Vertical lines: 256 Horizontal lines: 144 Resolution: 256 x 144 pix Size: 8m x 4.5m Panels: 144 (16 x 9) Power: 8 x 20A (110V) Drivers: 3 Net Out: Out 1 J Ports: 1 ~ 9 Driver 1 Width = 64... -
Page 19: Special Applications
Special Applications Pattern 1 System Information Vertical lines: 208 Horizontal lines: 96 Resolution: 208 x 96 pix Size: 6.5m x 3m Panels: 52 (pattern) Power: 3 x 20A (110V) Drivers: 4 Net Out: Out 1 J Ports: 1 ~ 6 This space is optional. -
Page 20: Appendix
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. -
Page 21: Technical Specifications (Per Panel)
ENVIRONMENTAL Ambient temperature ...14° – 104°F (-10° – 40°C) ORDERING INFORMATION DV Wall™ Panel Set (4 panels in flight case) ... DVM-HR DV Wall™ Studio (software, PCI card, cables) ... DVW Studio DV Wall™ Driver ...DVW Driver Flying Bracket for DVM-HR ...DVM-BR Technical Support Address: Service Dept.