HP BRIO BA410 Manual page 35

There's a Problem with the CD-ROM, CD-RW or DVD Drive
Have you checked that...
There is a disc inserted in the drive
The program is correctly configured for your
drive
The device boot order is set correctly in the
program
The hardware is working properly
Advanced Troubleshooting
Have you checked that...
All cables (data, power and audio) have been properly
connected both to the drive and to the system board.
The jumpers on the drive are set correctly
F F F F o o o o r r r r m m m m o o o o r r r r e e e e i i i i n n n n f f f f o o o o r r r r m m m m a a a a t t t t i i i i o o o o n n n n o o o o n n n n u u u u s s s s i i i i n n n n g g g g a a a a nd nd nd nd tr tr tr tro o o o ub ub ub ubl l l l e e e e s s s s ho ho ho hoo o o o t t t t i i i i n n n n g y g y g y g yo o o o u u u u r r r r D D D D V V V V D D D D d d d d r r r r i i i i v v v v e e e e , , , , r r r r e e e e f f f f e e e e r t r t r t r to o o o t t t t h h h h e e e e P P P P C C C C ' ' ' ' s s s s on on on onli li li lin n n n e e e e H H H H P P P P B B B B r r r r i i i i o o o o C C C C en en en ent t t t e e e e r r r r
All manuals and user guides at all-guides.com
How
Ö
Click on the drive letter assigned to your
drive in Windows Explorer. If you receive
a message such as D D D D : : : : \ \ \ \ i i i i s s s s n n n n o o o o t t t t
a a a a c c c c c c c c e e e e ss ss ss ssi i i i b b b b l l l l e e e e / / / / d d d d e e e e v v v v i i i i c c c c e e e e i i i i s s s s no no no not t t t r r r r e e e e a a a a d d d d y y y y , this means
there is no disc in the drive.
Open the drive and check whether there
is a disc inside.
Ö
Enter the
startup, then:
Make sure you have enabled the O O O O n n n n - - - - c c c c h h h h i i i i p p p p
P P P P r r r r i i i i m m m m a a a a r r r r y y y y I I I I D D D D E E E E and the O O O O n n n n - - - - c c c c h h h h i i i i p p p p S S S S e e e e c c c c on on on ond d d d a a a a r r r r y y y y
I I I I D D D D E E E E fields under H H H H a a a a r r r r d d d d w w w w a a a a r r r r e e e e P P P P r r r r o o o o t t t t e e e e c c c c t t t t i i i i o o o o n n n n in
the B B B B o o o o o o o o t t t t menu.
Go to the A A A A d d d d v v v v a a a a n n n n c c c c e e e e d d d d menu. You should
see a CD-ROM, CD-RW or DVD-ROM
drive declared in the I I I I D D D D E E E E D D D D e e e e v v v v i i i i c c c c e e e e s s s s
submenu.
Ö
Enter the
at startup, then go to the B B B B o o o o o o o o t t t t menu. If
you intend to boot from the CD-ROM
drive, you should place C C C C D D D D - - - - R R R R O O O O M M M M before
H H H H D D D D D D D D in the B B B B o o o o o o o o t t t t Ö Ö Ö Ö B B B B oo oo oo oot t t t D D D D e e e e v v v v i i i i c c c c e e e e P P P P r r r r i i i i o o o o r r r r i i i i t t t t y y y y
submenu.
Ö
Run e-DiagTools to see if it detects a
problem with the drive (refer to page 42).
How
Ö
Check that the drive's power and data
cables are correctly connected at both ends
(drive and system board). Refer to page 62
for connections to the drive and page 57 for
connections to the system board.
Ö
Check that the jumpers on the hard drive
are in CS (cable select) mode
Hardware Problems
program by pressing at
program by pressing