Hunter Hydrawise PRO-C Software/App Owner's Manual
  1. Manuals
  2. Brands
  3. Hunter Manuals
  4. Irrigation System
  5. PRO-C Hydrawise
  6. Software/app owner's manual

Hunter Hydrawise PRO-C Software/App Owner's Manual

Irrigation controllers
Hide thumbs Also See for Hydrawise PRO-C:

Advertisement

Table of Contents

Advertisement

Table of Contents
loading

Related Manuals for Hunter Hydrawise PRO-C

Summary of Contents for Hunter Hydrawise PRO-C

  • Page 2: Table Of Contents

    HCC - Installing ICM Station Modules HCC - Wire Distance to Valves HCC - Installing Wi-Fi Antenna Extension Kit Can Two Zones Run Simultaneously with a HCC controller? HCC - Configure Controller Offline Copyright 2021 Hunter Industries. All Rights Reserved.

  • Page 3: Hcc - Quick Start Guide

    IMPORTANT: If you are using the plug-in method, the wiring is exactly the same but you will require an outlet. The plug referred to as a Pigtail (three wires including neutral, hot, and ground) can be purchased at most hardware outlets or a Hunter Authorized Dealer (P/N: PIGTAIL).
  • Page 4 REMOVE FACEPACK 1. Turn AC power off at the source, and verify that it is off. 2. Disconnect the facepack ribbon cable 3. Remove the facepack. 4. Remove the cover from the junction box. Copyright 2021 Hunter Industries. All Rights Reserved.
  • Page 5 Connect the incoming green wire (GROUND) with the green and yellow wire from the transformer. Cap the unused brown wire coming from the transformer. Replace the cover of the junction box and screw it into place. 7. Replace cover, turn on the power, and test. Copyright 2021 Hunter Industries. All Rights Reserved.

  • Page 6: Hcc - Power Module Wiring Diagram

    5. Red Rain Sensor 6. Black Flow Meter 7. C Common 8. P/MV Pump or Master Valve 9. REM Remote Control Input 10. White Sensor Common 8. Red Rain Sensor 9. Black Flow Meter Copyright 2021 Hunter Industries. All Rights Reserved.

  • Page 7: Hcc - Valve Wiring

    5. Strip ½" (13 mm) of insulation from ends of all wires. Secure valve common wire to C (Common) terminal on any of the valve modules or power module. Then attach all individual valve control wires to appropriate station terminals. HCC CONTROLLER Copyright 2021 Hunter Industries. All Rights Reserved.

  • Page 8: Hcc - Installing Icm Station Modules

    Model Max Station Count Total ICM 800 Modules Total ICM 2200 Modules Qty:2 - ICM-800 Qty:1 - ICM-2200 HCC-800-PL Qty:4 - ICM-800 Qty:1 - ICM-2200 HCC-800-M Qty:4 - ICM-800 Qty:1 - ICM-2200 HCC-800-SS Copyright 2021 Hunter Industries. All Rights Reserved.

  • Page 9: Hcc - Wire Distance To Valves

    Flip the locking lever into the horizontal the controller control panel. This is Connect field and common wiring as locked position. required for the controller to recognize needed and test. the new module. HCC - Wire Distance to Valves Copyright 2021 Hunter Industries. All Rights Reserved.
  • Page 10 Below is a chart indicating the maximum wire run between the controller and the Hunter AC solenoid valves. Valve Wire Sizing (Feet) Ground Control Wire 1040 1210 1350 1460 1540 1590 1040 1340 1650 1920 2150 2330 2440 1210 1650...

  • Page 11: Hcc - Installing Wi-Fi Antenna Extension Kit

    Conduit Mounting Hardware Used for HCC and ACC2 model controllers. Please visit an authorized Hunter distributor near you using our interactive Distributor Lookup IMPORTANT: Use only one cable extension, as combining the two will incur a signal loss. Steps Illustrations Step 1: Open the front panel to access the antenna compartment.
  • Page 12 (fit the cable through the slot). Adjust holder length by sliding upper body into the lower body. Step 8: Drop the antenna holder into threaded conduit fitting, and allow the holder rim to rest on top of the fitting. Copyright 2021 Hunter Industries. All Rights Reserved.

  • Page 13: Can Two Zones Run Simultaneously With A Hcc Controller

    Can Two Zones Run Simultaneously with a HCC controller? The HCC controller has the ability to operate two Hunter valves at one time therefore, allows for more than one program to run at the same time. Only two programs can be allowed to run concurrently.
  • Page 14 Run Times = 10 Minutes each zone Program Name = B Watering Days = Everyday Start Time = 4:05 AM Run Times = 10 Minutes each zone Controller Screen Example (After 4:05 AM) Copyright 2021 Hunter Industries. All Rights Reserved.

  • Page 15: Hcc - Configure Controller Offline

    Touch the ADD button to add a program start time and follow the steps below. You can toggle between zones by touching NEXT or PREVIOUS buttons or you can leave the start time to APPLY TO ALL ZONES. Copyright 2021 Hunter Industries. All Rights Reserved.

This manual is also suitable for:

Hydrawise hcc-800-plHydrawise hcc-800-mHydrawise hcc-800-ssHydrawise hcc-800-pp

Table of Contents