Specifications - Dremel STYLO+ 2050 Operating/Safety Instructions Manual

operating procedures or conditions and can be avoided by taking
proper precautions as given below.
a. Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. The
operator can control kickback forces, if proper precautions
are taken.
b. use special care when working corners, sharp edges etc.
avoid bouncing and snagging the accessory. Corners,
sharp edges or bouncing have a tendency to snag the rotat-
ing accessory and cause loss of control or kickback.
c. Do not attach a toothed saw blade. Such blades create
frequent kickback and loss of control.
d. always feed the bit into the material in the same direction
as the cutting edge is exiting from the material (which is
the same direction as the chips are thrown). Feeding the
tool in the wrong direction causes the cutting edge of the bit
to climb out of the work and pull the tool in the direction of
this feed.
e. When using rotary files, cut-off wheels, high-speed cut-
ters or tungsten carbide cutters, always have the work
securely clamped. These wheels will grab if they become
slightly canted in the groove, and can kickback. When a
cut-off wheel grabs, the wheel itself usually breaks. When a
rotary file, high-speed cutter or tungsten carbide cutter grabs,
it may jump from the groove and you could lose control of
the tool.
SAFETY WARNINGS SPECIFIC FOR GRINDING AND
ABRASIVE CUTTING-OFF OPERATIONS
a. use only wheel types that are recommended for your
power tool and only for recommended applications. for
example: do not grind with the side of a cut-off wheel.
Abrasive cut-off wheels are intended for peripheral grinding,
side forces applied to these wheels may cause them to
shatter.
b. for threaded abrasive cones and plugs use only undam-
aged wheel mandrels with an unrelieved shoulder flange
that are of correct size and length. Proper mandrels will
reduce the possibility of breakage.
c. Do not "jam" a cut-off wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut. Over-
stressing the wheel increases the loading and susceptibility to
twisting or snagging of the wheel in the cut and the possibility
of kickback or wheel breakage.
d. Do not position your hand in line with and behind the
rotating wheel. When the wheel, at the point of operation,
is moving away from your hand, the possible kickback may
propel the spinning wheel and the power tool directly at you.
e. When wheel is pinched, snagged or when interrupting a
cut for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to a
complete stop. Never attempt to remove the cut-off wheel
from the cut while the wheel is in motion otherwise kickback
may occur. Investigate and take corrective action to eliminate
the cause of wheel pinching or snagging.
f. Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut.
The wheel may bind, walk up or kickback if the power tool is
restarted in the workpiece.
g. Support panels or any oversized workpiece to minimize
2610Z09886.indd 4
the risk of wheel pinching and kickback. Large workpieces
tend to sag under their own weight. Supports must be placed
under the workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
h. use extra caution when making a "pocket cut" into exist-
ing walls or other blind areas. The protruding wheel may
cut gas or water pipes, electrical wiring or objects that can
cause kickback.
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b. allow brushes to run at operating speed for at least one
minute before using them. During this time no one is to
stand in front or in line with the brush. Loose bristles or
wires will be discharged during the run-in time.
c. Direct the discharge of the spinning wire brush away
from you. Small particles and tiny wire fragments may be
discharged at high velocity during the use of these brushes
and may become imbedded in your skin.
d. Do not exceed 15,000 rpM when using wire brushes.
DO NOT WORK WITH MATERIALS
WARNING
!
CONTAINING ASBESTOS (ASBESTOS IS
CONSIDERED CARCINOGENIC).
TAKE PROTECTIVE MEASURES WHEN
WARNING
!
DURING WORK DUST CAN DEVELOP
THAT IS HARMFUL TO ONE'S HEALTH, COMBUSTIBLE OR
ExPLOSIVE (SOME DUSTS ARE CONSIDERED
CARCINOGENIC); WEAR A DUST MASK AND WORK WITH
DUST/CHIP ExTRACTION WHEN CONNECTABLE.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
RECYCLING
In case of discard of this product, do not dispose into
household waste! Take to a Dremel approved technical
assistance so they will give the proper destination
following non-aggression criteria to the environment,
recycling the parts and complying with valid local law.

SPECIFICATIONS

GENERAL SPECIFICATIONS
Model no 2050
Voltage Rating 100-240V~ 50-60Hz, 18Vdc, 0.5A
Max. Speed 22,000/min
Chuck Capacity 0.8mm - 3.2mm
Maximum diameter
of Accessory 31.8mm
Power supply 2610Z09745 (AR),
2610Z09883 (BO, BR, CL, PE, PY, UY)
ExTENSION CORDS
Use completely unrolled and safe extension cords with a capacity
of 5A.
4
1/18/18 7:48 AM