3M Peltor ComTac VI Manual page 11

EN
ANZ). Press [+] to select and press and hold [+] to confirm your
selection.
NOTE: Make sure that you are using the approved frequency for
the region you are operating in.
Factory reset
Resets all menu settings to the factory default values. This setting
needs to be confirmed by pressing [+] when the voice says
"confirm factory reset".
TROUBLESHOOTING FOR NIB
Problem Possible Causes
The headset beeps NIB channel busy
when transmitting. by four people.
The headset beeps No other headset
when transmitting. in the perimeter.
Can't hear or You are not using
communicate with the correct NIB
others. frequency for the
region you are
operating in.
Can't hear or The NIB is not
communicate with activated.
others.
CLEANING AND MAINTENANCE
Use a cloth wetted with soap and warm water to clean the outer
shells, headband and ear cushions.
NOTE: Do NOT immerse the hearing protector in water. If the
hearing protector gets wet from rain or sweat, turn the earmuffs
outwards, remove the ear cushions and foam liners, and allow
to dry before reassembly. The ear cushions and foam liners
may deteriorate with use and should be examined at regular
intervals for cracking or other damage. When used regularly, 3M
recommends replacing the foam liners and ear cushions at least
twice a year to maintain consistent attenuation, hygiene, and
comfort. If an ear cushion is damaged, it should be replaced.
See Spare Parts Section below.
REMOVING AND REPLACING THE EAR CUSHIONS
F:1 To remove the ear cushion, slide your fingers under the
inside edge of the ear cushion and firmly pull straight out.
F:2 Remove existing liner(s) and insert new foam liner(s).
F:3 Fit one side of the ear cushion into the groove of the earcup
and then press on the opposite side until ear cushion snaps in
place.
APPLYING MIKE PROTECTOR TAPE
To protect the boom speech microphone from humidity and dirt,
use microphone protector HYM1000.
Attaching the protector (Fig G):
G:1 Use a pair of scissors to cut 100 mm of mike protector tape.
Remove the protective paper.
G:2: Place the microphone in the end of the tape as shown in
the picture.
G:3 Fold the protecor tape and make sure that the microphone
is covered.
G:4 Press tighly to seal the protector tape.
G:5 The microphone is now ready to use.
SPARE PARTS AND ACCESSORIES
3M™ PELTOR™ HY68 SV Hygiene kit
Suggestion
Replaceable hygiene kit. Replace at least twice a year to ensure
constant attenuation, hygiene and comfort.
Wait for an
available spot.
3M™ PELTOR™ HY80-EU Gel cushion hygiene kit
Make sure
there is another
3M™ PELTOR™ HY100A Single-use protectors
headset in use
Single-use protector that is easy to fit to the ear cushions.
in the perimeter.
3M™ PELTOR™ MT73 Water-proof microphone
Choose the
Waterproof dynamic speech microphone.
correct NIB
frequency in the
3M™ PELTOR™ M171/2 Windshield for microphone
menu. See NIB
frequency.
3M™ PELTOR™ HYM1000 Microphone protector
Toggle between
Moisture- and wind-resistant tape that protects the speech
the different
microphone.
modes with the
PTT button. See
3M™ PELTOR™ M60/2 Wind protection for the surrounding
Activating NIB.
microphones
3M™ PELTOR™ HY450/1 Head pad
To be used for small size range fitting for foldable headbands.
3M™ PELTOR™ LR03NM Battery AAA NiMH
WARRANTY AND LIMITATION OF LIABILITY
WARRANTY: In the event any 3M Personal Safety Division
product is found to be defective in material, workmanship, or not
in conformity with any express warranty for a specific purpose,
3M's only obligation and your exclusive remedy shall be at 3M's
option, to repair, replace or refund the purchase price of such
parts or products upon timely notification of the issue by you
and substantiation that the product has been stored, maintained
and used in accordance with 3M's written instructions.
EXCEPT WHERE PROHIBITED BY LAW, THIS WARRANTY
IS EXCLUSIVE AND IS IN LIEU OF ANY EXPRESS OR
IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE OR OTHER WARRANTY
OF QUALITY, OR THOSE ARISING FROM A COURSE OF
DEALING, CUSTOM OR USAGE OF TRADE, EXCEPT OF
TITLE AND AGAINST PATENT INFRINGEMENT. 3M has no
obligation under this warranty with respect to any product that
has failed due to inadequate or improper storage, handling, or
maintenance; failure to follow product instructions; or alteration
or damage to the product caused by accident, neglect, or
misuse.
5