Kenwood NX-3220 K Service Manual page 88

No. RX
13 Single Tone Decode
(979.9Hz)
14 None
15 None
16 MSK Decode
NXDN Type Signaling
No. RX
1 RAN1
2 None
3 RAN1
7 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
RAN: Radio Access Number
PN9: Pseudo-Random Pattern
No.7, 9 Item: PC test mode only
DMR Type Signaling
No. RX
1 CC 00 Burst
2 PN9
3 CC 00 Burst
4 CC 00 Burst
5 CC 00 Burst
6 SYNC (Each Slot) +
PN9 Burst Pattern
7 SYNC (Super Frame) +
PN9 Burst Pattern
8 CC 00 Burst
9 Tone Pattern
10 Silence Pattern
11 Audio Test Pattern
12 Vocoder Loop
1-88 (No.RA053<Rev.001>)
TX
Single Tone Encode
(979.9Hz)
Single Tone Encode
(1000Hz)
MSK PN9
MSK Encode
TX
RAN1
PN9
Maximum Deviation
Pattern
FSW + PN9
TX
CC 00 Burst
PN9
Maximum Deviation
Pattern
1/3 Deviation Pattern
0 Continuous Pattern
SYNC (Each Slot) + PN9
Burst Pattern
SYNC (Super Frame) +
PN9 Burst Pattern
0 Burst Pattern
Tone Test Burst Pattern
Silence Burst Pattern
Audio Test Burst Pattern
None
4.21 Panel Tuning Mode (K2 and K3 types only)
4.21.1 Transceiver tuning (To enter tuning mode)
To enter tuning mode, press the [
is in test mode. Use the [
tuning modes, and the [  ]/[  ] button to adjust tuning
requirements (1 to 4096 appears on the LCD).
Use the [ ] button to select the adjustment item through tuning
modes. Use the [ ] button to adjust 5, 9 or 17 reference level
adjustments, and use the [  ] button to switch between Wide/
Narrow.
• LCD display in panel tuning mode
CV voltage, AD value, etc
Sub LCD display 2.6
L1
An
Main LCD display
Adjustment point
H1
L1
H2
L2
H3 An : Analog narrow mode
L3
C1
Aw : Analog wide 5k mode
C2
As : Analog wide 4k mode *1
C3
Nn : NXDN narrow mode
Nv : NXDN very narrow mode
D : DMR mode
*1: Wide 4k is displayed only when the PC test mode is used. However, it aims
at production for factory, or a operation verification of the transceiver. It is not
necessary in operation of the transceiver to adjust.
4.21.2 Button operation
Button
Push
[Selector] -
[  ] Adjustment value up
[  ] Adjustment value down
[  ] Auto adjustment start
[  ] Wide/Narrow/NXDN/DMR -
[ Side1 ] -
[ Side2 ] -
[ ] Shift to panel test mode
[ ] To enter 5 or 9 reference
level adjustments
[ ] Writes the adjustment
value
[ ] Go to next adjustment
item
[AUX -
(Orange)]
[PTT] Transmit
[0] to [9] -
and
[#],[ ]
] button while the transceiver
] button to write tuning data through
AST 256
Adjustment value
(1~4096)
Proper value guide
(When the frequency
adjustment is necessary,
or is displayed.)
Adjustment item
Function
Hold (1 second)
Continuation up
Continuation down
Output tone pattern
change of balance
adjustment (A change is
possible only during
balance adjustment.)
-
-
-
Back to last adjustment
item (At the time of 5, 9 or
17 point adjustment:
Adjustment point change)
-