Advertisement
Quick Links
EBA2880 eZ.HD Series
8MP, IP66 IR Dome Camera
User's Manual
Copyright © EverFocus Electronics Corp.
Release Date: September, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw
Advertisement
Related Manuals for EverFocus EBA2880
Summary of Contents for EverFocus EBA2880
- Page 1 The images may vary depending on the product and software version. Information contained in this document is subject to change without notice. EverFocus Taiwan: 2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw...
- Page 2 1. Introduction EverFocus eZ.HD series cameras – EBA2880 deliver 8MP image quality. The model is equipped with CMOS sensor and provides motorized 3.6-11mm lens with ICR. Featured with True Wide Dynamic Range (T-WDR), the camera can provide clear images even under backlight circumstances where intensity of illumination can vary excessively.
-
Page 3: Installation
1.4 Optional Accessory BA-E320 Color / Material: White / Metal Size (Φ x H): 138 x 54mm / 5.43” x 2.13” Weight: 700g / 1.5lb BA-EB45 Color / Material: White / Metal Size (W x D x H): 245 x 160 x 163mm / 9.65”x 6.3”x 6.42” Weight: 2.1kg / 4.63lb 1.5 Cable Description 12VDC... - Page 4 a. If you want to wire the cables from the Side Cut on the Camera Base: Attach the Camera Body to the Camera Base and run the cables through the Camera Base, and then place the cable under the Side Cut. Finally, screw the Camera Base to the surface with the supplied 4 Screws.
- Page 5 5. Connect the Power Cable to a 12VDC power source. Connect the Video Output Cable to a monitor or DVR. 6. You can use the Joystick on the cable to configure camera OSD settings. Remove the Protection Cap from the Joystick before using it. Configuring OSD Settings: Push the Joystick up / down to select •...
- Page 6 3. Configuration in the OSD Menu No Main Sub Menu Sub Menu / Function AF Mode One Shot, Manual Motorized D&N Filter Sync On, Sync Off Initial Brightness 0-20 Auto Mode Normal / Deblur 1/30, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, Shutter Manual Speed...
- Page 7 D>N Thres 0-20 N>D Thres 0-20 Delay High, Middle, Low IR LED Adaptive, Off Anti-Sat. 0-20 Extern SW High, Low Extern D>N Thres 0-20 N>D Thres 0-20 Delay High, Middle, Low Auto Autoext Preset Color C-Temp 3000K, 5000K, 8000K Manual R-Gain 0-20 B-Gain...
- Page 8 CR Level 0-20 Trans Window Use Window Zone On, Off Det H-POS 0-96 Det Window Det V-POS 0-56 Det H-Size 0-96 Motion Det V-Size 0-56 Sensitivity 0-10 Motion OSD On, Off Text Alarm On, Off Signal Out On, Off Frame Rate 4K/15fps, 4MP/30fps, 1080p/30fps Freq 60Hz (Auto Detection)