Related Manuals for Lincoln Electric HANDY MIG
Summary of Contents for Lincoln Electric HANDY MIG
- Page 1 IM3000 11/2020 REV02 HANDY MIG / HANDY CORE OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland www.lincolnelectric.eu...
-
Page 2: Table Of Contents
12/05 THANKS! For having choosen the QUALITY of the Lincoln Electric products. Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified immediately to the dealer. For future reference record in the table below your equipment identification information. Model Name, Code & Serial Number can be found on the machine rating plate. -
Page 3: Technical Specifications
Technical Specifications NAME INDEX HANDY MIG K14000-1 HANDY CORE K14001-1 INPUT Input Voltage U Input Power at Rated Cycle Frequency 230V± 10% 2.5 kW @ 20% Duty Cycle 50/60Hz 1-phase CORE RATED OUTPUT Duty Cycle 40°C Output Current Output Voltage (based on a 10 min. -
Page 4: Eco Design Information
Efficiency and idle power consumption: Efficiency when max power consumption Index Name Equivalent model / Idle power consumption K14000-1 HANDY MIG 50,4 % / 26W No equivalent model Idle state occurs under the condition specified in below table IDLE STATE Condition Presence... - Page 5 Typical gas usage for MIG/MAG equipment: DC electrode positive Wire Wire Feeding Gas flow Material type diameter Shielding Gas Current Voltage [m/min] [l/min] [mm] Carbon, low 0,9 ÷ 1,1 95 ÷ 200 18 ÷ 22 3,5 – 6,5 Ar 75%, CO alloy steel Aluminium 0,8 ÷...
-
Page 6: Electromagnetic Compatibility (Emc)
If any electromagnetic disturbances are detected the operator must put in place corrective actions to eliminate these disturbances with, if necessary, assistance from Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. -
Page 7: Safety
Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or equipment damage. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. - Page 8 WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area and have a fire extinguisher easily accessible. Welding sparks and hot materials from the welding process can easily go through small cracks and openings to adjacent areas. Do not weld on any tanks, drums, containers, or material until the proper steps have been taken to insure that no flammable or toxic vapors will be present.
-
Page 9: Introduction
(MIG) welding and the Innershield electrode process (self- steel electrode and flux-cored electrode (for HANDY MIG) shielded flux-cored welding). The machine will handle and only flux-cored electrode (for HANDY CORE). - Page 10 High output range. When the cylinder pressure gauge pointer stops moving, open the valve fully. Changing Polarity (only for Handy MIG) 1. For Negative Polarity welding (DC-): Refer to below 2. Keep the cylinder valve closed, except when welding. Figure. As delivered, the machine is wired for...
- Page 11 2. Select and install the welding wire to match the process. Use Genuine Lincoln Electric Brand wire. Wire quality is essential for successful welding. 3. Install the drive roll, contact tip, and nozzle appropriate for the weld process.
- Page 12 We respond to our customers based on the best become null and void. information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, Any noticeable damage should be reported immediately and assumes no liability, with respect to such information and repaired.
-
Page 13: Weee
12/05 Part List reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine. -
Page 14: Suggested Accessories
Suggested Accessories 1361-410-005 GAS HOSE ONLY FOR HANDY MIG 2,5M 0742-200-939 GAS NOZZLE ONLY FOR HANDY MIG 0742-200-936 FLUX NOZZLE (GASLESS) 0742-200-938 CONTACT TIP 0.6 MM ONLY FOR HANDY MIG 0742-200-937 CONTACT TIP 0.9 MM 2886-162-011 CHIPPING HAMMER/BRUSH 0657-229-003 HANDSHIELD 0744-180-047...