Advertisement
Quick Links
Advertisement
Related Manuals for Rinnai Control-R RWM101
Summary of Contents for Rinnai Control-R RWM101
- Page 1 ENGLISH...
- Page 3 Before installing and operating the module, be sure to read these instructions to familiarize yourself with the module’s features and functionality. If you contact Rinnai, please have your module’s AYLA ID available (located on the back of the module). Write the number here for your convenience: AYLA ID: •...
- Page 5 The table below describes possible states for each of the LED color indicators. Color State Condition Yellow Solid Wi-Fi module booting up or updating firmware Blinking Searching for IP address Solid Ready to pair and register Green Solid In accessory pairing mode – searching for wireless on-demand recirculation accessory (push button, motion sensor, etc.)
- Page 6 • Choose a central location where the Wi-Fi signal is strong. IMPORTANT Basements, crawl spaces, attics, garages, and mechanical rooms may have poor wireless signals. • Additional wiring can run up to 300 feet (91 meters) away from the water heater to ensure a strong wireless signal (18-22 gauge wire is required).
- Page 7 You Will Need • Module (supplied) • Two wall anchors and two screws (supplied) IMPORTANT: The anchors and screws are for mounting to the wall; do not insert them into the tankless water heater. • Tools (field-supplied): Phillips head screwdriver, drill with bit set, level and pencil The module’s back panel contains two keyhole slots ❶...
- Page 8 Insert the two wall anchors (supplied) into each ❸ hole until they sit flush against the wall. DO NOT insert the anchors into the water heater. Insert the screws (supplied) into the anchors and ❹ fasten to the wall leaving 1/4 in. exposed. DO NOT insert the screws into the water heater.
- Page 9 WARNING To protect yourself from harm, follow the steps below before wiring the module: • Turn off the electrical power supply by unplugging the power cord or by turning off the electricity at the circuit breaker. The temperature controller does not control the electrical power.
- Page 10 ❸ Route the module controller cable through the grommet (located on the bottom, right side of the unit) and connect to the mating terminal on the bottom, right side of the PC Board. MODULE Board Controller Mating Grommet Cable Terminal Under Unit Important: If your module wires include spade end connectors, follow the steps below:...
- Page 11 ❸ • Place the two module wires through the bottom opening of the water heater. • Attach each module wire to the two screws labeled Terminal for Controls. Partially unscrew each of the − two screws. Remote control cable Insert the spade terminal −...
- Page 12 30 feet. Visit rinnai.us/wifi for additional resources including: • Control-R Push Button Installation Instructions • Control-R Motion Sensor Installation Instructions • Recirculation with On-Demand Accessories User Guide • On-Demand Recirculation Quick Start Guide (Module...
- Page 13 ❶ • Push Button - Requires two CR2450 watch batteries (included with push button) • Motion Sensor - Requires one 2600mAh AA size Lithium-Thionyl Chloride battery (3.6V or 3.7V) (included with motion sensor) ❷ Pair the Push Button or Motion Sensor to the module. You Will Need: •...
- Page 14 Press and hold down the Connect button on the module until the LED turns solid GREEN. Then, release the button (you will need to repeat this process to pair each accessory). You have five minutes to pair the push button or motion sensor with the module before pairing mode times out.
- Page 15 Refer to the tankless water heater installation and operation manual for more information on Circ-Logic (Rinnai’s recirculation technology) and recirculation parameter/dip switch settings.
- Page 16 ❸ Install the push button or motion sensor near the water fixture that will be used frequently, such as a kitchen faucet or bathroom sink. Refer to the instructions in the push button or motion sensor package for detailed installation steps. Adhere to any wall or counter service using the adhesive backing.
- Page 17 You Will Need: • Mobile device connected to home/business network • Router with Wi-Fi • 2.4 GHz Wi-Fi network ❶ The module LED will blink yellow until boot-up is complete and will then turn solid RED.
- Page 18 ❷ Download the Control-R™ app to your smartphone or ® ® tablet from the Apple Store or Google Play Store. Rinnai Control-R™ Rinnai America Corp ❸...
- Page 19 • For questions about your Internet service, contact your Internet Service Provider (ISP) • Contact Rinnai Customer Care at 1-800-621-9419 and have your module’s AYLA ID available (located on back of module) Scan the QR code to find troubleshooting...
- Page 20 Product Rinnai Control-R™ Wi-Fi Module Part Number RWM101 Module 4.8 oz (0.14 kg) Weight Shipping 6 oz (0.17 kg) Carton 3.69 in. x 3.69 in. x 1.18 in. Module (94 mm x 94 mm x 29.97 mm) Dimensions (w, h, d): Shipping 6.125 in.
- Page 21 802.11N Wi-Fi 5 GHz networks − The Lime Condition (LC) notification will not appear in the Control-R™ App when the module is paired with the following series of Rinnai Tankless Water Heaters manufactured prior to 2009: VA, VB, KA and V53e...
- Page 22 5.0 or higher • BlackBerry® devices are NOT supported Pairing Module pairs to only one Rinnai Tankless Water Heater. FCC Part 15 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: •...
- Page 24 100000400(03) 02/2020...