Page 1
10:21 pm 11 :25 pm Thursday MENU Set to WIFI Current Temperature ZONES MANUAL HEAT SCHEDULE MODE Temporary ON / OFF Rinnai Touch Wi-Fi Kit Installation & Configuration Manual APPLY MODULE IDENTIFICTION LABEL...
Page 2
HOME OWNER TO RETAIN FOR FUTURE REFERENCE...
Page 3
The Terms and Conditions are available when downloading the While the supply of the information is voluntary, if our customers Rinnai Touch App used to connect with the Wi-Fi Module. Please cannot, or do not wish to provide the information sought, the read these carefully before proceeding.
Page 4
It may also be used to alert against unsafe practices. WARNING. The Rinnai Touch Wi-Fi Module is supplied with a 12V DC Plug Pack Socket if required. Only this power supply must WARNING be used.
This is useful if the Touch Wi-Fi Module cannot be located Connection close to a GPO. Two-wire Bus Two-wire bus connection that allows connection to heating/cooling appliances, N-C3/N-C6 Networker controllers Connection and N-T1 temperature sensors. Rinnai Touch Wi-Fi Kit IM...
IMPORTANT Below are the QR codes to download the Rinnai Touch App from either the Apple Store or Google Play. If unable to scan the QR code, visit the appropriate App store and search ‘Rinnai Touch’ to locate and download it.
Where possible locate the Touch Wi-Fi Module so that its front Wi-Fi Module away from them. panel indicators are visible from a man hole. Touch Wi-Fi Module WIFI Touch Wi-Fi Module WIFI Wi-Fi Router Wi-Fi Router Rinnai Touch Wi-Fi Kit IM...
Page 11
WIFI Wi-Fi Router DO NOT locate the Touch Wi-Fi Module under the house. DO NOT locate the Touch Wi-Fi Module outside the house. Wi-Fi Router Touch Wi-Fi Touch Wi-Fi Module Wi-Fi Router Module WIFI WIFI Rinnai Touch Wi-Fi Kit IM...
(20m interconnecting cable Networker Controller P/N: INTERMODTOUCH included in the Touch (Not included in the Touch Wi-Fi Kit) Wi-Fi Kit) (0.75mm figure - 8 cable field supplied) N-C3 / N-C6 LINK Networker Controller Touch Wi-Fi Module Rinnai Touch Wi-Fi Kit IM...
Page 13
ON / OFF LINK MODE MANUAL SCHEDULE Touch Wi-Fi Module ZONES 6:15 Sunday 6:15 Sunday MENU MENU HEAT HEAT Set to Set to ON / OFF ON / OFF MODE MODE MANUAL SCHEDULE MANUAL SCHEDULE ZONES ZONES Rinnai Touch Wi-Fi Kit IM...
Keep pressing the ‘AP’ button until the Wi-Fi indicator flashes orange. d. Next, run your Rinnai Touch App ensuring you carefully follow the on-screen prompts as these will guide you through the process of configuring your Touch Wi-Fi Module for connection to your Wi-Fi Router.
Page 15
When navigating through the configuration process using the Rinnai Touch App, eventually a screen like that shown will be displayed that lists all the Wi-Fi CONFIGURE MODULE Router SSIDs that have been detected by the Touch Wi-Fi Module along with...
• If for some reason the Rinnai Touch App cannot locate the Touch Wi-Fi Module on your Wi-Fi Network it is more than likely your Wi-Fi Router is blocking these UDP broadcast packets as a result of configuration settings within the Wi-Fi Router.
Touch Wi-Fi Module using the Rinnai Touch App. Any number of devices can register to connect with your Touch Wi-Fi Module, the process being as simple as just running the Rinnai Touch App on the device and following the prompts to allow the device to locate the Touch Wi-Fi Module on the Wi-Fi Network. When doing this: 1.
All that is needed to allow your device to access your Touch Wi-Fi Module via the cloud is to connect to your Touch Wi-Fi Module over your Wi-Fi Network once. Once connected, the necessary Rinnai Cloud Server access credentials will be extracted from the Touch Wi-Fi Module and will be saved to the device. The symbol will be displayed by the Rinnai Touch App when cloud connected to the Touch Wi-Fi Module.
Page 19
Touch Wi-Fi Module such that the following screen is displayed by CONNECT the Rinnai Touch App. On changing the Wi-Fi Router the Touch Wi-Fi Module will need to be reconfigured so that it can connect to the new Wi-Fi Router Could not connect to your Touch with different SSID/WPA credentials.
Page 20
“Sensor fault – n11 Code#53” Then follow Step 4 of the Installation and Configuration section to reconfigure your Touch Wi-Fi Module. The Rinnai Touch App will step you through the above process when the Touch Wi-Fi Module not accessible option is selected.
Page 21
Wi-Fi Module is in the Home Direct/Router Mode and a packet transfer has occurred. Wi-Fi Module is waiting for switch over to the Default AP state after being in the Router Solid Mode for at least 3 minutes without being able to connect with the named router. Rinnai Touch Wi-Fi Kit IM...
Page 22
Touch Wi-Fi Module. Server type 2 connection type 1 error. This error will not allow system access out of house. If the problem persists replace the Touch Wi-Fi Module. Server type 2 connection type 2 error. Rinnai Touch Wi-Fi Kit IM...
Page 23
Before placing a warranty call, refer to the Troubleshooting Guide or FAQs listed in the Owner’s Manual ‘Connecting and Navigating the App’ to assist in finding a resolution. • For further information go to the Rinnai website, www.rinnai.com.au and follow the Wi-Fi links. Rinnai Touch Wi-Fi Kit IM...
Page 24
Tel: 1300 555 545* Fax: 1300 555 655 Monday to Friday, 8.00 am to 5.00 pm EST. *Cost of a local call higher from mobile or public phones. For further information visit www.rinnai.com.au or email enquiry@rinnai.com.au innai has a Service and Spare Parts network with personnel who are fully trained and equipped to give the best service on your innai appliance.