1. Manuals
  2. Brands
  3. Encore Manuals
  4. Switch
  5. ENHGS-800
  6. Manual

Encore ENHGS-800 Manual

Hide thumbs Also See for ENHGS-800:
Table of Contents

Advertisement

Quick Links

Download this manual
CE Declaration of conformity
This equipment complies with the requirements relating to electromagnetic compatibility,
EN 55022 class A for ITE, the essential protection requirements of Council Directive
89/336/EEC on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if no installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into a different outlet from that the receiver is connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance, could affect the user's authority to operate the equipment.
Copyright © 2001 All Rights Reserved.
Company has an on-going policy of upgrading its products and it may be possible that
information in this document is not up-to-date. Please check with your local distributors
for the latest information. No part of this document can be copied or reproduced in any
form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
1

Advertisement

Table of Contents
loading

Related Manuals for Encore ENHGS-800

Summary of Contents for Encore ENHGS-800

  • Page 1 CE Declaration of conformity This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE, the essential protection requirements of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility.

  • Page 2: Table Of Contents

    Table of Contents 1. Unpacking Information 2. Introduction To 10/100/1000Mbps Gigabit Switch General Description Key Features The Front Panel 2.3.1 System LEDs 2.3.1.1 Power LED 2.3.2 Port LEDs 2.3.2.1 Speed/Link and Act LED 2.3.2.2 FDX LED The Rear Panel 2.4.1 Power Connecting 3.

  • Page 3: Unpacking Information

    1. Unpacking Information Thank you for purchasing the 8 port 10/100/1000Mbps Gigabit switch. Before you start, please check all the contents of this package. The product package should include the following: 1. One 8-port 10/100/1000Mbps Gigabit Switch 2. One power cord 3.

  • Page 4: Introduction To 10/100/1000Mbps Gigabit Switch

    2. Introduction To 10/100/1000Mbps Gigabit Switch 2.1 General Description The device is a powerful, high-performance 10/100/1000Mbps Fast Ethernet and Gigabit switch, with all 8 ports capable of 10/100/1000Mbps auto-negotiation operation (NWay), which means the switch could automatically negotiate with the connected partners on the network speed and duplex mode.

  • Page 5: Key Features

    2.2 Key Features The switch provides the following key features: Complies with 10BASE-T specifications of the IEEE802.3 standard. Complies with 100BASE-TX specifications of IEEE802.3u standard. Complies with 1000BASE-T specifications of IEEE802.3ab standard. Eight RJ-45 ports for 10BASE-T, 100BASE-TX and 1000BASE-T connectivity. Supports NWay protocol for speed (10/100/1000Mbps) Supports half/full duplex on 10/100Mbps speed and full-duplex on 1000Mbps speed.

  • Page 6: The Front Panel

    2.3 The Front Panel The front panel of the switch is shown as below. The auto-negotiation feature of the switch allows each port of the device running at one of the following operation modes: Port Speed Duplex Mode Gigabit 1000 Mbps Full-duplex 100 Mbps Full duplex...

  • Page 7: System Leds

    LED Definition The rich diagnostic LEDs on the front-panel can provide the operating status of individual port and whole system. The following table is a summary for LEDs definition. Type Status Operation System Power Steady Green Power is on Power is off Port 100M Steady Green...

  • Page 8: Speed/Link And Act Led

    2.3.2.1 Speed/Link and Act LED Every port has three LED(100M, 10M, Activity) for indicating the speed and connection status. If the port is connected but the Speed/Link LED(100M/10M) and Activity(ACT) LED is dark, check the following items: 1. The switch and the connected device’s power are on or not 2.

  • Page 9: Installing And Using 10/100/1000Mbps Gigabit Switch

    3. Installing and Using 10/100/1000Mbps Gigabit Switch 3.1 Installing The 10/100/1000Mbps Gigabit Switch The switch does not require software configuration. Users can immediately use most of the features of this product simply by attaching the cables and turning the power on. 3.1.1 Desktop Installation For desktop installation, the switch needs to put on a clean, flat desk or table close to a power outlet.

  • Page 10: Installing Network Cables

    Rack Mounting the Switch The switch should be able to fit in the 19-inch rack. 1. Disconnect all cables from the switch before continuing. 2. Place the unit on a hard, flat surface with the front facing toward you. 3. Locate a mounting bracket over the mounting holes on one side of the unit. 4.

  • Page 11: Network Application

    3.1.3.3 Network Application...

  • Page 12: Mac Address Table & Learning

    4. Switch Operation 4.1 MAC Address Table and Learning The switch is implemented with a MAC address table, which is composed of many entries. Each entry is used to store the address information of network nodes on the network, including MAC address, port ID, etc. The information is the most important base to do packet filtering and forwarding.

  • Page 13: Product Specifications

    5. Product Specifications Standard IEEE802.3, 10BASE-T IEEE802.3u, 100BASE-TX IEEE802.3ab, 1000BASE-T Interface RJ-45 x 8 10/100/1000 ports (Auto MDI-X) Cable Connections RJ-45 (10BASE-T) : UTP Category 3,4,5 RJ-45 (100BASE-TX) : UTP Category 5 RJ-45 (1000BASE-T): UTP Category 5 Network Data Rate Gigabit Ethernet (10/100/1000Mbps) Transmission Mode Gigabit Ethernet (Full/Half duplex)

Table of Contents