Table 29 - Discharge Air Temp. Sensor Temperature/Voltage/Resistance Correlation - York YLUA0248 Series Installation Operation & Maintenance

SECTION 9 – SERVICE AND TROUBLESHOOTING
TABLE 29 - DISCHARGE AIR TEMP. SENSOR
TEMPERATURE/VOLTAGE/
RESISTANCE CORRELATION
TEMP °F VOLTAGE RESISTANCE
0 1.71
2 1.78
4 1.85
6 1.93
8 2.00
10 2.07
12 2.15
14 2.22
16 2.30
18 2.37
20 2.45
22 2.52
24 2.59
26 2.67
28 2.74
30 2.81
32 2.88
34 2.95
36 3.02
38 3.08
40 3.15
42 3.21
44 3.27
46 3.33
48 3.39
50 3.45
52 3.51
54 3.56
56 3.61
58 3.67
60 3.72
62 3.76
64 3.81
66 3.86
68 3.90
70 3.94
72 3.98
74 4.02
76 4.06
78 4.10
80 4.13
140
TEMP °C
25619 -18
24046 -17
22580 -16
21214 -14
19939 -13
18749 -12
17637 -11
16599 -10
15629 -9
14721 -8
13872 -7
13077 -6
12333 -4
11636 -3
10982 -2
10370 -1
9795 0
9256 1
8750 2
8276 3
7830 4
7411 6
7017 7
6647 8
6298 9
5970 10
5661 11
5370 12
5096 13
4837 14
4593 16
4363 17
4145 18
3941 19
3747 20
3564 21
3392 22
3228 23
3074 24
2928 26
2790 27
Discharge Air Temperature Sensor
J6-5 = +5 VDC regulated supply to sensor.
J6-8 =
VDC input signal to the microboard.
See Table 31 for voltage readings that
correspond to specific discharge tem-
peratures.
J6-2 = drain (shield connection = 0 VDC)
Analog Inputs – Pressure
Refer to the unit wiring diagram. Pressure inputs are
connected to the microboard on plugs J7 and J9. These
analog inputs represent varying dc signals correspond-
ing to varying pressures. All voltages are in reference
to the unit case (ground).
System 1 discharge and suction pressures will be con-
nected to J7 of the microboard. System 2 discharge and
suction pressure transducers will be connected to J9 of
the microboard.
The discharge transducers are optional on all units. If
the discharge transducers are not installed, no connec-
tions are made to the microboard and the discharge
pressure readout on the display would be zero.
The suction pressure transducers are standard on all
YLUA's. The suction pressure transducers have a
range of 0 to 400 PSIG. The output will be linear from
0.5VDC to 4.5VDC over the 400 PSIG (27.5 barg)
range.
The discharge transducers have a range from 0 to
650 PSIG. The output will be linear from 0.5VDC to
4.5VDC over the 650 PSIG (41.25 barg) range. Fol-
lowing is the formula that can be used to verify the
voltage output of the transducer. All voltage reading
are in reference to ground (unit case).
FORM 150.73-NM2
ISSUE DATE: 09/07/2020
JOHNSON CONTROLS