Sharp MX-2314N Service Manual page 140

Main Sub
62 8 Used to format the hard disk/SD Card. (HDD: Excluding the Operation Manual, the watermark data, and
the system area) (SD Card: User data)
10 Used to clear the job completion list data.
11 Used to delete the document filing data.
12 Used to set Enable/Disable of auto format in a hard disk trouble.
13 Used to format the hard disk. (Operation Manual, watermark data only)
14 Used to delete the document filing management data.
63 1 Used to display the shading correction result.
2 Used to perform shading.
3 Used to perform scanner (CCD) color balance and gamma auto adjustment.
4 Used to display the SIT chart patch density.
5 Used to perform the scanner (CCD) color balance and gamma default setting.
6 Used to display the scan level and the density level of the copy color balance adjustment patch.
7 Used to register the service target of the copy mode auto color balance adjustment.
8 Used to set the default of the service target of the copy mode auto color balance adjustment.
11 Used to set the target color balance of the copy mode auto color balance adjustment.
64 1 Test print. (Self print) (Color mode)
2 Test print. (Self print) (Monochrome mode)
4 Printer test print. (Self print)
5 Printer test print. (Self print) (PCL)
6 Printer test print. (Self print) (PS)
7 Used to print the adjustment pattern of the test print .(Self print).
(The adjustment pattern of SIM46-21 is printed.)
65 1 Used to adjust the touch panel (LCD display section) detection coordinates.
2 Used to display the touch panel (LCD display section) detection coordinates.
5 Used to check the operation panel key input.
66 1 Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while
checking with the LCD.
2 Used to enter a country code and set the default value for the country code.
3 Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the
result.
4 Used to send the selected signals to the line and the main unit speaker. (Send level: max.)
5 Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting)
(For the kinds of send signals, refer to SIM66-04.)
6 Used to print the confidential registration check table (BOX NO., BOX name, passcode. (If there is no
confidential registration, no print is made.)
7 Used to output all image data saved in the image memory. (Confidential data are also outputted.)
8 Used to send the selected sound messages to the line and the speaker. (Send level: Max.)
9 Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting)
* For details of sound messages, refer to the sound message table of SIM66-08.
10 Used to clear the FAX and image send image data. (The confidential data are also cleared.)
11 Used to send the selected signal at 300bps to the line and the speaker. (Send level: Max.)
12 Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting)
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.
13 Used to register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be registered.)
14 Used to execute the dial pulse (10PPS) send test and to adjust the make time.
15 Used to execute the dial pulse (20PPS) send test and to adjust the make time.
16 Used to execute the DTFM signal send test and to adjust the send level.
17 Used to send the DTMF signal to the line and the speaker. (Send level: Max.)
18 Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting)
21 Used to print the selected items (system error, protocol monitor).
22 Used to set the handset sound volume. (This simulation can be executed even though the handset setting
is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.) (Japan
model only)
24 Used to clear the FAST save data.
29 Used to initialize the telephone book data (the one-touch registration table, the FTP/Desktop expansion
table, the group expansion table, the program registration table, the interface memory box table, the meta
data, InboundRouting, and the DocumentAdmin table).
30 Used to display the TEL/LIU status change, The display is highlighted by status change.
31 Used to set ON/OFF the port for output to TEL/LIU.
32 Used to check the fixed data received from the line and to display the result.
33 Used to execute detection of various signals with the line connected and to display the detection result.
When a signal is detected, the display is highlighted.
34 Used to execute the send test and display the time required for sending image data in the test. Used to
execute send test and display. (Unit: ms)
36 Used to check send and receive data from the MODEM controller to the MFP controller or the data line or
the command line individually.
39 Used to check and change the destination setting saved in EEPROM of the FAX BOX.
42 Used to rewrite the program to power control installed in the FAX BOX.
43 Used to write the adjustment value into the power control installed in the FAX BOX.
61 Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while
checking with the LCD.
62 Used to import the FAX receive data into a USB memory in PDF file type.
Functions
MX-3114N SIMULATION 6 – 7
Section
HDD
Scanner
Scanner
Operation panel section
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX