Behringer EUROPOWER PMP6000 Quick Start Manual page 3

EUROPOWER
PMP6000
PMP4000
PMP1680S
Classic Control, State-of-the-Art Sound
Leave the mic preamps at home, because the
quality of sound that was once only available
in the studio is ready to go wherever you do.
Built-in, boutique-caliber mic preamps with
switchable +48 V phantom power make it possible
to use either dynamic or condenser mics with the
PMP Series. The PMP6000 gives you 12 mic inputs
while the PMP4000 and PMP1680S each give you
8 mic inputs.
Built-in Digital Eff ects Processor
The new generation of PMP mixers come
equipped with 24-bit FX processors, giving you
100 mind-blowing digital eff ect presets such
as delay, chorus and reverb. Apply them to any
channel, as well as to the monitors and main
output. In case you're pulling double duty as sound
engineer and performer, the FX processors features
a footswitch jack for remote on/off . Of course,
if you have treasured outboard gear you've grown
attached to, these mixers can integrate them into
the mix while leaving out the built-in FX processor.
Changing the Channels
The PMP Series gives you excellent
fl exibility to accommodate whatever a
performance requires. You get 12 (PMP6000)
or 8 (PMP4000 and PMP1680S) channels for mics,
guitars and other mono instruments. Stereo
channels 13-20 (PMP6000), 9-16 (PMP4000) and
7-10 (PMP1680S) are designed to work in pairs as
stereo channels, or independently for more mono
instruments. All mono channels have
3-band EQ, switchable Low cut fi lter for
eliminating infrasonics, and Clip LEDs to
indicate when the input signal is too hot.
A STANDBY switch (PMP6000 and
PMP1680S) mutes all mic channels during
breaks, preventing the microphones from
picking up noise or interference. You can
leave all faders untouched while you play a
CD via the CD/TAPE inputs.
PHANTOM Switch
provides 48V to
the XLR inputs
for use with
condenser mics
GRAPHIC EQ
adjusts specifi c
frequencies
MULTI-FX
PROCESSOR adds
selected sound
eff ect to any
channel whose FX
knob is turned up
SURROUND
knob adjusts the
amount of stereo
enhancement on
the mix. Press the
XPQ TO MAIN
button to activate
the eff ect
FX (SEND) fader(s)
adjust signal sent
to internal FX
processor and FX
SEND jack(s)
MON (SEND)
fader(s) adjust
output of MON
SEND jacks and
OUTPUT A when
using MON 1/
MONO mode
MAIN fader(s)
adjust the output
of main signal
The FBQ Feedback Detection
system automatically shows you which
frequencies are causing feedback. Just
touch the FBQ button and watch the red
LEDs on the 7-band graphic EQ pinpoint
show you which frequencies to adjust for
optimized sound, without the feedback.
SPEAKER
PROCESSING
switch allows mixer
POWER AMP to compensate
switch selects for speakers with
operation mode of limited low end
power amp frequency response
Page 3 of 8
Continued on next page
STANDBY
button mutes
all mic channels
(PMP6000)
VU METERS display
main and monitor
output signal
levels
CD/TAPE adjusts
volume of CD/TAPE
IN signal in main or
monitor mix
MAIN 2 knob
(PMP4000/6000)
adjusts output of
MAIN 2 jacks
PHONES/CTRL
ROOM knob
adjusts headphone
and control room
output volume
FX TO MON and
FX TO MAIN knobs
adjust amount of
signal from internal
multi-FX processor
included in main or
monitor mix
MONO fader
adjusts output
of MONO OUT
jack