ZyXEL Communications Prestige 128IMH User Manual
  1. Manuals
  2. Brands
  3. ZyXEL Communications Manuals
  4. Network Router
  5. Prestige 128IMH
  6. User manual
ZyXEL Communications Prestige 128IMH User Manual

ZyXEL Communications Prestige 128IMH User Manual

Isdn/modem router/hub
Hide thumbs Also See for Prestige 128IMH:
Table of Contents

Advertisement

Quick Links

Download this manual
Prestige 128IMH
User's Guide
Version 1.0
ZyXEL
T
I
A
S
OTAL
NTERNET
CCESS
OLUTION

Advertisement

Table of Contents
loading

Related Manuals for ZyXEL Communications Prestige 128IMH

Summary of Contents for ZyXEL Communications Prestige 128IMH

  • Page 1 Prestige 128IMH User's Guide Version 1.0 ZyXEL OTAL NTERNET CCESS OLUTION...
  • Page 2 ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein.
  • Page 3 Notice 2 Shielded RS-232 cables are required to be used to ensure compliance with FCC Part 15, and it is the responsibility of the user to provide and use shielded RS-232 cables. ECC Interference Statement Prestige 128IMH ISDN Modem/ Router/Hub...
  • Page 4 Prestige 128IMH ISDN Modem/ Router/Hub Information for Canadian Users The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Industry Canada does not guarantee that the equipment will operate to a user's satisfaction.
  • Page 5 The Prestige 128IMH has been approved for connection to the Public Switched Telecommunication Network using interfaces compatible with ITU-TSS recommendation I.420 (Basic Rate ISDN user access). The Prestige 100IH complies with the following directives: 1. The Council Directive 89/336/EEC of 3 May 1992 on the approximation of the laws of the member states relation to Electro Magnetic Compatibility.

  • Page 6: Zyxel Limited Warranty

    Prestige 128IMH ISDN Modem/ Router/Hub ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period, and upon proof...
  • Page 7 Downloads ROM upgrades) ZyXEL Communications Corp., 6 Regular Innovation Road II, Science-Based Mail Industrial Park, Hsinchu, Taiwan 300, R.O.C Prestige 128IMH ISDN Modem/ Router/Hub OUTSIDE NORTH AMERICA See your local distributor (check http://www.zyxel.com for a listing) sales@zyxel.com.tw www.zyxel.com +886-3-5782439 Ext.266...

  • Page 9: Table Of Contents

    1.3 The Built-In Modem ...1-5 1.4 Applications for Prestige 128IMH...1-5 Chapter 2...2-1 Hardware Installation & Initial Setup...2-1 2.2 Prestige 128IMH Rear Panel and Connections ...2-2 2.3 Additional Installation Requirements ...2-3 2.4 Power On Your Prestige ...2-5 2.5 Navigating the SMT Interface...2-7 2.6 Changing the System Password...2-10...
  • Page 10 Prestige 128IMH ISDN Modem/ Router/Hub 2.10 Protocol Dependent Ethernet Setup... 2-20 Chapter 3... 3-1 Internet Access ... 3-1 3.1 Route IP Setup... 3-1 3.2 TCP/IP Parameters ... 3-2 3.3 TCP/IP Ethernet Setup and DHCP ... 3-5 3.4 Internet Access Configuration... 3-8 3.5 Single User Account ...
  • Page 11 9.2 Setting Up Supplemental Phone Service...9-2 9.3 The Flash Key ...9-2 9.4 Call Waiting...9-2 9.5 Three way calling ...9-3 9.6 Call Transfer ...9-4 9.7 Call Forwarding ...9-5 Chapter 10 ...10-1 Filter Configuration ...10-1 10.1 About Filtering ...10-1 Table of Contents Prestige 128IMH ISDN Modem/ Router/Hub...
  • Page 12 Prestige 128IMH ISDN Modem/ Router/Hub 10.2 Configuring a Filter Set ... 10-3 10.3 Configuring a Filter Rule ... 10-7 10.4 Novell IPX Filter Rule... 10-13 Chapter 11 ... 11-1 SNMP Configuration... 11-1 11.1 About SNMP ... 11-1 11.2 Configuring SNMP... 11-1 Chapter 12 ...
  • Page 13 Problems with the LAN Interface...15-3 15.4 Problems Connecting to a Remote Node or ISP...15-3 15.5 Problems for Remote User to Dial-in ...15-3 ISDN Information Worksheet ... 1 Acronyms and Abbreviations... 1 Index... 1 Table of Contents Prestige 128IMH ISDN Modem/ Router/Hub xiii...

  • Page 15: List Of Figures

    Figure 1-2 LAN-to-LAN Connection Application... 1-7 Figure 1-3 Telecommuting/Remote Access Server Application... 1-8 Figure 2-1 Front Panel ... 2-1 Figure 2-2 Prestige 128IMH Rear Panel and Connections... 2-2 Figure 2-3 Power-On Display... 2-5 Figure 2-4 Login Screen ... 2-6 Figure 2-5 SMT Main Menu... 2-9 Figure 2-6 Menu 23 - System Security ...
  • Page 16 Prestige 128IMH ISDN Modem/ Router/Hub Figure 4-1 Menu 11 – Remote Node Setup ...4-2 Figure 4-2 Menu 11.1 Remote Node Profile ...4-3 Figure 4-3 Menu 11.2 - Remote Node PPP Options...4-9 Figure 4-4 Menu 11.5 – Remote Node Filter ...4-10 Figure 5-1 TCP/IP LAN-to-LAN Application ...5-1...
  • Page 17 Prestige 128IMH ISDN Modem/ Router/Hub Figure 8-3 Menu 13 – Default Dial-in Setup ... 8-4 Figure 8-4 Default Dial-in Filter... 8-8 Figure 8-5 Menu 14 - Dial-in User Setup... 8-8 Figure 8-6 Edit Dial-in User... 8-9 Figure 8-7 Multiple Server Configuration... 8-13 Figure 10-1 Outgoing Packet Filtering Process...
  • Page 18 Prestige 128IMH ISDN Modem/ Router/Hub Figure 14-8 Menu 24.4 - System Maintenance - Diagnostic...14-11 Figure 14-9 Trace Display for a Successful Manual Call ...14-13 Figure 14-10 Trace Display for a Failed Authentication...14-13 Figure 14-11 Menu 24.7 - System Maintenance - Upload Firmware ...14-15 Figure 14-12 Menu 24.7.1 - Uploading Router Firmware ...14-15...
  • Page 19 Prestige 128IMH ISDN Modem/ Router/Hub List of Tables Table 1-1 ISDN Phone Line Info ...xxv Table 1-2 IP subnet masks and the number of hosts allowed... xxvi Table 2-1 LED functions... 2-1 Table 2-2 Main Menu Commands ... 2-7 Table 2-3 Main Menu Summary ... 2-9 Table 2-4 General Setup Menu Fields...
  • Page 20 Prestige 128IMH ISDN Modem/ Router/Hub Table 7-1 Bridge Ethernet Setup Menu - Handle IPX Field Configuration...7-2 Table 7-2 Remote Node Network Layers Menu Bridge Options...7-4 Table 7-3 Bridge Static Route Menu Fields...7-6 Table 8-1 Remote Dial-in Users/Remote Nodes Comparison Chart ...8-1 Table 8-2 Default Dial-in Setup Fields...8-5...
  • Page 21 Prestige 128IMH ISDN Modem/ Router/Hub Table 14-6 Call Control Parameters Fields...14-22 Table 14-7 Call History Fields...14-25 Table 15-1 Troubleshooting the Start-Up of your Prestige... 15-1 Table 15-2 Troubleshooting the ISDN Line ... 15-2 Table 15-3 Troubleshooting the LAN Interface... 15-3 Table 15-4 Troubleshooting a Connection to a Remote Node or ISP ...

  • Page 23: Preface

    About Your Router/Hub Congratulations on your purchase of the Prestige 128IMH ISDN/Modem Router/Hub. The Prestige 128IMH is a high-performance bridge/router that offers a complete solution for your WAN (Wide Area Network) applications such as Internet access, multi-protocol LAN-to-LAN connections, telecommuting and remote access over ISDN (Integrated Service Digital Network).
  • Page 24 Prestige 128IMH ISDN Modem/ Router/Hub If you have an ISDN line installed and working, you can reference the following sections to insure that your line is set up properly to allow all the features of your Prestige to operate. To order a new ISDN line, do the following: 1.

  • Page 25: Table 1-1 Isdn Phone Line Info

    You have now collected all of the necessary information about your ISDN telephone line. Make sure that these values are entered into your ‘Setup Information Worksheet’ before you continue to the next section. Preface Prestige 128IMH ISDN Modem/ Router/Hub Table 1-1 ISDN Phone Line Info Geography Europe, Asia...

  • Page 26: Table 1-2 Ip Subnet Masks And The Number Of Hosts Allowed

    Prestige 128IMH ISDN Modem/ Router/Hub Collecting Ethernet Setup Information IP Address - An IP Address is required for TCP/IP protocol. The IP Address is the unique 32-bit number assigned to your Prestige. This address is written in dotted decimal notation (four 8-bit numbers, between 0 and 255, separated by periods), e.g., 192.168.1.1.
  • Page 27 Syntax Conventions For brevity’s sake, we will use “e.g.” as a shorthand for “for instance” and “i.e.” for “that is” or “in other words” throughout this manual. Preface Prestige 128IMH ISDN Modem/ Router/Hub xxvii...

  • Page 29: Chapter 1

    This chapter describes the key features and applications of your Prestige. Prestige 128IMH ISDN/Modem Bridge Router The Prestige 128IMH is an ISDN bridge/router with an integrated 4-port Ethernet 10Base-T hub and a 56K modem. The Prestige is ideal for everything from Internet browsing to receiving calls from remote dial - in users to making LAN-to-LAN connections to remote networks.
  • Page 30 Prestige 128IMH ISDN Modem/ Router/Hub Single User Account (SUA) The SUA™ (Single User Account) features allows multiple users to share a single user account. Incoming Call Support In addition to making outgoing calls, the Prestige allows you to configure it as a remote access server for telecommuting employees.
  • Page 31 Data Compression Your Prestige incorporates Stac data compression to speed up data transfer. Stac is the de facto standard of data compression over PPP links. Getting to know your Prestige Prestige 128IMH ISDN Modem/ Router/Hub...
  • Page 32 LAN or WAN. Upgrade P128IMH Firmware via LAN PCT allows upgrading of the Prestige 128IMH firmware over the local LAN. Supplementary Voice Features The Prestige supports the following Supplementary Voice Features on both of its Analog (POTS)

  • Page 33: The Built-In Modem

    Internet uses exclusively. It is also compatible with access servers manufactured by major vendors such as Cisco and Ascend. A typical Internet Access application is shown below. Getting to know your Prestige Prestige 128IMH ISDN Modem/ Router/Hub...

  • Page 34: Figure 1-1 Internet Access Application

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 1-1 Internet Access Application Internet Single User Account For a SOHO (small office/Home Office) environment, your Prestige offers a Single User Account (SUA) feature that allows multiple users on the LAN (Local Area Network) to access the Internet concurrently for the cost of a single user.

  • Page 35: Figure 1-2 Lan-To-Lan Connection Application

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 1-2 LAN-to-LAN Connection Application 1.4.3 Remote Access Server Your Prestige allows remote users to dial-in and gain access to your LAN. This feature enables users that have workstations with remote access capabilities, e.g., Windows 95, to dial in to access the network resources without physically being in the office.

  • Page 36: Figure 1-3 Telecommuting/Remote Access Server Application

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 1-3 Telecommuting/Remote Access Server Application Getting to know your Prestige...

  • Page 37: Chapter 2

    The LED blinks when the connected station is transmitting. PHONE: 1/2 The LED is on when the device on the corresponding POTS port is in use. Hardware Installation and Setup Prestige 128IMH ISDN Modem/ Router/Hub ISDN Figure 2-1 Front Panel Table 2-1 LED functions...

  • Page 38: Prestige 128Imh Rear Panel And Connections

    The figure below shows the rear panel of your Prestige 128MH and the connection diagram. Figure 2-2 Prestige 128IMH Rear Panel and Connections This section outlines how to connect your Prestige 128MH to the LAN and to the ISDN network.

  • Page 39: Additional Installation Requirements

    1. A computer with Ethernet 10Base-T NIC (Network Interface Card). 2. A computer equipped with communications software configured to the following parameters: VT100 terminal emulation. 9600 Baud. No parity, 8 Data bits, 1 Stop bit. Hardware Installation and Setup Prestige 128IMH ISDN Modem/ Router/Hub...
  • Page 40 Prestige 128IMH ISDN Modem/ Router/Hub After the Prestige is properly set up, you can make future changes to the configuration through telnet connections. Hardware Installation and Setup...

  • Page 41: Power On Your Prestige

    When you power on your Prestige, it performs several internal tests as well as line initialization. After the initialization, the Prestige asks you to press Copyright (c) 1994 - 1998 ZyXEL Communications Corp. ethernet address: 00:a0:c5:98:23:12 Resetting ISDN firmware.(2) ZyXEL Prestige DSS1: V 099 Entering Password Step 2.

  • Page 42: Figure 2-4 Login Screen

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 2-4 Login Screen Hardware Installation and Setup...

  • Page 43: Navigating The Smt Interface

    Type 99, then Exit the SMT press [Enter]. Hardware Installation and Setup Prestige 128IMH ISDN Modem/ Router/Hub Table 2-2 Main Menu Commands To move forward to a sub-menu, type in the number of the desired sub-menu and press [Enter]. Press the [Esc] key to move back to the previous menu.
  • Page 44 Prestige 128IMH ISDN Modem/ Router/Hub Hardware Installation and Setup...

  • Page 45: Figure 2-5 Smt Main Menu

    After you enter the password, the SMT displays the Main Menu, as shown below. Copyright (c) 1994 – 199 8 ZyXEL Communications Corp. Getting Starte d 1. General Setup 2. ISDN Setup 3. Ethernet Setup 4. Internet Access Setup Advanced Applications 11.

  • Page 46: Changing The System Password

    Prestige 128IMH ISDN Modem/ Router/Hub Dial-in User Setup SUA Server Setup Filter Set Configuration SNMP Configuration System Security System Maintenance Exit Changing the System Password The first thing your should do before anything else is to change the default system password by following the steps below.

  • Page 47: Figure 2-7 Menu 23.1 - System Security - Change Password

    Note that as you type a password, the screen displays a (X) for each character you type. Hardware Installation and Setup Menu 23.1 – System Security - Change Password Old Password= XXXX New Password= XXXX Retype to confirm= XXXX Enter here to CONFIRM or ESC to CANCEL: Prestige 128IMH ISDN Modem/ Router/Hub 2-11...

  • Page 48: General Setup

    Prestige 128IMH ISDN Modem/ Router/Hub General Setup Menu 1 - General Setup contains administrative and system-related information. To enter Menu 1 and fill in the required information, follow these steps: Enter 1 in the Main Menu to open Menu 1 – General Setup.

  • Page 49: Table 2-4 General Setup Menu Fields

    Prestige does not route are simply discarded. Compared to routing, bridging generates far more traffic for the same network protocol and consumes more CPU cycles and memory. Hardware Installation and Setup Table 2-4 General Setup Menu Fields Prestige 128IMH ISDN Modem/ Router/Hub Example P128IMH MyHouse JohnDoe...

  • Page 50: European Isdn Setup Menus

    Prestige 128IMH ISDN Modem/ Router/Hub European ISDN Setup Menus Menu 2 is for you to enter the information about your ISDN line. Please note that the Prestige only accepts digits in phone number fields; please do no include ‘-‘ or spaces in these fields.

  • Page 51: Pabx Outside Line Prefix

    Prestige 128IMH ISDN Modem/ Router/Hub Call Routing is either A/B Adapter 1 or 2, then the Prestige uses Global Analog Call to decide how to handle global calls. If you set Global Analog Call to Accept, then global calls are routed to the port according to the Analog Call Routing setting;...
  • Page 52 Prestige 128IMH ISDN Modem/ Router/Hub isdn initstring set AT&ZOx=number where x is 'I' for ISDN data calls, 'A' for A/B Adapter 1 and 'B' for A/B Adapter 2. For instance, isdn initstring set AT&ZOI=100&ZOA=101&ZOB=102 sets the calling party number to 100 for ISDN data calls, 101 for A/B adapter 1 and 102 for A/B adapter 2.

  • Page 53: Figure 2-9 Menu 2 - Isdn Setup

    Select Yes in the Advanced Setup field of Menu 2 – ISDN Setup above to display menu 2.1 below. Hardware Installation and Setup Prestige 128IMH ISDN Modem/ Router/Hub Figure 2-9 Menu 2 – ISDN Setup Table 2-5 Menu 2 – ISDN Setup This field is fixed as DSS1.

  • Page 54: Figure 2-10 Isdn Advanced Setup

    Prestige 128IMH ISDN Modem/ Router/Hub ISDN Call Waiting This allows you to place a call on hold while you answer another incoming call on the same telephone (directory) number. By default call waiting is disabled on both telephone ports, but can be enabled on either port from Menu 2.1...

  • Page 55: Ethernet Setup

    Figure 2-12 Menu 3 - Ethernet Setup Menu 3.1 - General Ethernet Setup Input Filter Sets: protocol filters= 2 device filters= Output Filter Sets: protocol filters= device filters= Press ENTER to Confirm or ESC to Cancel: Prestige 128IMH ISDN Modem/ Router/Hub 2-19...

  • Page 56: Protocol Dependent Ethernet Setup

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 2-13 Menu 3.1 - General Ethernet Setup If you need to define filters, please read Chapter 9- Filter Set Configuration, then return to this menu to define the filter sets. 2.10 Protocol Dependent Ethernet Setup Depending on the protocols for your applications, you need to configure the respective Ethernet Setup, as outlined below.

  • Page 57: Chapter 3

    To edit Menu 1, enter 1 in the Main Menu to select General Setup and press [Enter]. Set the Route IP field to Yes by pressing the space bar. Internet Access Prestige 128IMH ISDN Modem/ Router/Hub Menu 1 - General Setup System Name= p128MH...

  • Page 58: Tcp/Ip Parameters

    Prestige 128IMH ISDN Modem/ Router/Hub TCP/IP Parameters 3.2.1 IP Address and Subnet Mask Similar to the houses on a street that share a common street name, the machines on a LAN share one common network number, also. Where you obtain your network number depends on your particular situation. If the ISP or your network administrator assigns you a block of registered IP addresses, follow their instructions in selecting the IP addresses and the subnet mask.

  • Page 59: Dhcp Configuration

    Prestige 128IMH ISDN Modem/ Router/Hub that it receives; when set to none, it will not send any RIP packets and will ignore any RIP packets received. The Version field controls the format and the broadcasting method of the RIP packets that the Prestige sends (it recognizes both formats when receiving).
  • Page 60 Prestige 128IMH ISDN Modem/ Router/Hub it. The DNS server addresses that you enter in the DHCP setup are passed to the client machines along with the assigned IP address and subnet mask. There are two ways that an ISP disseminates the DNS server addresses. The first is for an ISP to tell a customer the DNS server addresses, usually in the form of an information sheet, when s/he signs up.

  • Page 61: Tcp/Ip Ethernet Setup And Dhcp

    Press Space Bar to Toggle. Figure 3-2 Menu 3.2 – TCP/IP and DHCP Ethernet Setup Internet Access Prestige 128IMH ISDN Modem/ Router/Hub Menu 3.2 - TCP/IP and DHCP Ethernet Setup Enter here to CONFIRM or ESC to CANCEL: . The screen...

  • Page 62: Table 3-1 Dhcp Ethernet Setup Menu Fields

    Prestige 128IMH ISDN Modem/ Router/Hub Follow the instructions in the following table on how to configure the DHCP fields. Table 3-1 DHCP Ethernet Setup Menu Fields Field Description DHCP Setup DHCP= This field enables/disabled the DHCP server. If it is set to Server, your Prestige will act as a DHCP server.

  • Page 63: Table 3-2 Tcp/Ip Ethernet Setup Menu Fields

    Version Press the space bar to select the RIP version from RIP-1/RIP- 2B/RIP-2M. When you have completed this menu, press [Enter] at the prompt [Press ENTER to Confirm…] to save your configuration, or press [Esc] at any time to cancel. Internet Access Prestige 128IMH ISDN Modem/ Router/Hub 255.255.255.0 Example 192.168.1.1 (default)

  • Page 64: Internet Access Configuration

    Prestige 128IMH ISDN Modem/ Router/Hub Internet Access Configuration Menu 4 allows you to enter the Internet Access information in one screen. Menu 4 is actually a simplified setup for one of the remote nodes that you can access in Menu 11. Before you configure your Prestige for Internet access, you need to collect your Internet account information from your ISP.

  • Page 65: Figure 3-3 Menu 4 - Internet Access Setup

    ISP IP Addr Pri Phone and Sec Phone Number My Login Name My Password Internet Access Prestige 128IMH ISDN Modem/ Router/Hub Menu 4 - Internet Access Setup ISP's Name= myISP Pri Phone #= 1234 Sec Phone #= My Login= JohnDoe...
  • Page 66 Prestige 128IMH ISDN Modem/ Router/Hub Single User Account Telco Transfer options : Type Multilink Idle Timeout At this point, the SMT will ask if you wish to test the Internet connection. If you select Yes, your Prestige will call the ISP to test the Internet connection. If the test fails, note the error message that you receive on the screen and take the appropriate troubleshooting steps.

  • Page 67: Single User Account

    ISP. For example, this feature can be used to simplify the allocation of IP addresses when connecting branch offices to the corporate network. Internet Access Same Network Number 192.168.1.1 Prestige The SUA network appears as a single host to the Internet. Figure 3-4 Single User Account Topology Prestige 128IMH ISDN Modem/ Router/Hub INTERNET 3-11...

  • Page 68: Advantages Of Sua

    Prestige 128IMH ISDN Modem/ Router/Hub The IP address for the SUA can be either fixed or dynamically assigned when a call is connected. In addition, you can designate servers, e.g., a web server and a telnet server, on your local network and make them accessible to the outside world.

  • Page 69: Figure 3-5 Menu 4 - Internet Access Setup For Single User Account

    Press [Enter] at the message [Press ENTER to Confirm ...] to save your configuration, or press [Esc] at any time to cancel. Internet Access Prestige 128IMH ISDN Modem/ Router/Hub Menu 4 - Internet Access Setup ISP's Name= myISP Pri Phone #= 1234...

  • Page 70: Configuring Backup Isp Accounts

    Prestige 128IMH ISDN Modem/ Router/Hub At this point, your Prestige will ask if you wish to test the Internet connection. If you select Yes, the Prestige will call the ISP and test the configuration. If the test fails, note the error messages on the screen and take the appropriate troubleshooting steps.
  • Page 71 Enter Menu 11 again and select your Backup ISP. Step 3. In Menu 11.1, set the Active field to Yes. Step 4. You will now be able to access the Internet through the backup ISP Remote Node. Internet Access Prestige 128IMH ISDN Modem/ Router/Hub 3-15...

  • Page 73: Chapter 4

    From the Main Menu, select menu option 1. Remote Node Setup Step 1. When Menu 11 appears, as shown below, enter the number of the remote node that you Step 2. wish to configure. Remote Node Configuration Prestige 128IMH ISDN Modem/ Router/Hub Remote Node Configuration Chapter 4...

  • Page 74: Figure 4-1 Menu 11 - Remote Node Setup

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 4-1 Menu 11 – Remote Node Setup When Submenu 11.1. - Remote Node Profile appearsfill in the fields as described in the table below to define this remote profile. The Remote Node Profile Menu Fields table shows how to configure the Remote Node Menu.

  • Page 75: Figure 4-2 Menu 11.1 Remote Node Profile

    Enter the login name that this remote node will use when it calls your Prestige. The login name in this field combined with the Rem Node Password will be used to authenticate this node. Prestige 128IMH ISDN Modem/ Router/Hub Options Press space bar to toggle...
  • Page 76 Prestige 128IMH ISDN Modem/ Router/Hub Incoming: Rem Node Password Incoming: Rem CLID Incoming: Callback Outgoing: My Login Name Outgoing: Password Outgoing: Authen Outgoing: Pri(mary) Sec(ondary ) Phone Enter the password used when this remote node calls your Prestige. This field is applicable only if Call Direction is either Both or Incoming.
  • Page 77 Allocated Budget and Period do not apply. This field specifies if you want to make the connection to this remote node a nailed-up connection. See below for more details. Prestige 128IMH ISDN Modem/ Router/Hub Yes then press Yes then press Press space...

  • Page 78: Outgoing Authentication Protocol

    Prestige 128IMH ISDN Modem/ Router/Hub Session Option: Edit Filter Sets Session Option: Idle Timeout (sec) Once you have completed filling in Menu 11.1.1 – Remote Node Profile, press [Enter] at the message [Press ENTER to Confirm…] to save your configuration, or press [Esc] at any time to cancel.

  • Page 79: Table 4-2 Btr V Mtr For Bod

    BTR = 64, MTR = 64 BTR = 64, MTR = 128 BTR = 128, MTR = 128 Remote Node Configuration Prestige 128IMH ISDN Modem/ Router/Hub Table 4-2 BTR v MTR for BOD No. of Max No. of channel(s) used...

  • Page 80: Editing Ppp Options

    Prestige 128IMH ISDN Modem/ Router/Hub When bandwidth on demand is enabled, a second channel will be brought up if traffic on the initial channel is higher than the high Target Utility number for longer than the specified Add Persist value. Similarly, the second channel will be dropped if the traffic level falls below the low Target Utility number for longer than the Subtract Persist value.

  • Page 81: Figure 4-3 Menu 11.2 - Remote Node Ppp Options

    BOD Calculation Base Trans Rate Max Trans Rate Target Utility (kbps) Remote Node Configuration Prestige 128IMH ISDN Modem/ Router/Hub Description Select the CISCO PPP only when this remote node is a Cisco machine; otherwise, select the Standard PPP. Turn on/off Stac Compression. The default for this field is Off.

  • Page 82: Figure 4-4 Menu 11.5 - Remote Node Filter

    Prestige 128IMH ISDN Modem/ Router/Hub Add Persist Subtract Persist Once you have completed filling in Menu 11.2 - Remote Node PPP Options, press [Enter] at the message [Press ENTER to Confirm…] to save your configuration, or press [Esc] at any time to cancel.

  • Page 83: Chapter 5

    Prestige 128IMH ISDN Modem/ Router/Hub Chapter 5 Remote Node TCP/IP Configuration This chapter shows you how to configure the TCP/IP parameters of a remote node. A typical LAN-to-LAN application is to use your Prestige to connect a branch office to the headquarters, as depicted in the folllowing diagram.

  • Page 84: Figure 5-2 Menu 11.3- Remote Node Tcp/Ip Options

    Prestige 128IMH ISDN Modem/ Router/Hub 5.1.1 Remote Node Setup Follow the procedure in Chapter 5 - Remote Node Configuration to configure the protocol- independent parameters in Menu 11 - Remote Node Profile. For the TCP/IP parameters, follow the instructions below. If you are configuring your Prestige to receive incoming calls, you also need to set the default dial-in parameters in Menu 13.

  • Page 85: Figure 5-3 Sample Ip Addresses For A Tcpi/Ip Lan-To-Lan Connection

    Profile. Edit IP/IPX/Bridge Press the space bar to select Yes and press Enter to go to Menu 11.3 - Remote Node Network Layer Options Menu. Remote Node TCP/IP Configuration Prestige 128IMH ISDN Modem/ Router/Hub Local Network 192.168.2.0 192.168.3.2 Option (Yes/No)

  • Page 86: Table 5-2 Tcp/Ip Remote Node Configuration

    Prestige 128IMH ISDN Modem/ Router/Hub The following table shows the TCP/IP related fields in Menu 11.3 - Remote Node Network Layer Options. Table 5-2 TCP/IP Remote Node Configuration Rem IP Address This will show the IP address you entered for this remote node in the previous menu.

  • Page 87: Figure 5-4 Example Of Static Routing Topology

    Figure 5-4 Example of Static Routing Topology To configure an IP static route, use Menu 12, Static Route Setup, as displayed below. Remote Node TCP/IP Configuration Prestige 128IMH ISDN Modem/ Router/Hub Router 1 Menu 12 - Static Route Setup Router 2...

  • Page 88: Figure 5-5 Menu 12 - Static Route Setup

    Prestige 128IMH ISDN Modem/ Router/Hub From Menu 12, select one of the available IP static routes to open Menu 12.1 - IP Static Route Setup, as shown below. Figure 5-6 Menu 12.1 - IP Static Route Setup Choosing a static route to edit produces the following screen.

  • Page 89: Figure 5-7Edit Ip Static Route

    IP address of one of the remote nodes. Metric Same meaning as those in the Remote Node Setup. Private Same meaning as those in the Remote Node Setup. Remote Node TCP/IP Configuration Prestige 128IMH ISDN Modem/ Router/Hub Figure 5-7Edit IP Static Route...

  • Page 91: Chapter 6

    Prestige 128IMH ISDN Modem/ Router/Hub Chapter 6 IPX Configuration This chapter shows you how to configure the IPX parameters of the Prestige. IPX Network Environment Novell bundles the protocol stack, the server software and routing functionality in their NetWare server products. So a NetWare server is not only a file or print server, it is also a router.

  • Page 92: Frame Types

    Prestige 128IMH ISDN Modem/ Router/Hub 6.1.2 Frame Types IPX can run on top of four different frame types on the Ethernet. These frame types are 802.2, 802.3, Ethernet II (DIX), and SNAP (Sub-Network Access Protocol). Each frame type is a separate logical network, even though they exist on one physical cable.

  • Page 93: Figure 6-1 Netware Server

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 6-1 Netware Server IPX Configuration...

  • Page 94: Prestige In An Ipx Environment

    Prestige 128IMH ISDN Modem/ Router/Hub Prestige in an IPX Environment There are two scenarios in which your Prestige is deployed, depending on whether there is a Seed Router (Client Side) Assigns Network Number NetWare Clients NetWare server on the LAN, as depicted in the following diagram.

  • Page 95: Ipx Spoofing

    The built-in call filters are defined as follows: Block periodical RIP (Routing Information Protocol) and SAP (Service Advertising Protocol) response messages. Block NetWare serialization packets. Allow SAP and RIP inquiry packets. IPX Configuration Prestige 128IMH ISDN Modem/ Router/Hub...

  • Page 96: Ipx Ethernet Setup

    Prestige 128IMH ISDN Modem/ Router/Hub IPX Ethernet Setup From Menu 3 - Ethernet Setup, select option Novell IPX Setup to go to Menu 3.3 - Novell IPX Ethernet Setup as shown in the figure below. Press Space Bar to Toggle.

  • Page 97: Lan-To-Lan Application With Novell Ipx

    NetWare servers at the headquarters, as depicted in the figure below. Figure 6-4 LAN-to-LAN Application with Novell IPX IPX Configuration Prestige 128IMH ISDN Modem/ Router/Hub Corporate LAN External Network Number = 222...

  • Page 98: Figure 6-5 Menu 11.3 - Remote Node Novell Ipx Options

    Prestige 128IMH ISDN Modem/ Router/Hub 6.5.1 IPX Remote Node Setup Follow the procedure in Chapter 5 to configure the protocol-independent parameters in Menu 11.1 - Remote Node Profile. For the IPX-specific parameters in Menu 11.3 - Remote Node Network Layer Options, follow the instructions below. If you want the Prestige to receive incoming calls, you must also configure the default dial-in parameters in Menu 13.

  • Page 99: Table 6-2 Remote Node Novell Ipx Options

    Once you have completed filling in the Network Layer Options Menu, press [Enter] to return to Menu 11.1. Then press [Enter] at the message [Press ENTER to Confirm] to save your configuration, press [Esc] to cancel. IPX Configuration Prestige 128IMH ISDN Modem/ Router/Hub Option Yes/No 00000000...

  • Page 100: Figure 6-6 Menu 12.2 - Edit Ipx Static Route

    Prestige 128IMH ISDN Modem/ Router/Hub 6.5.2 IPX Static Route Setup Similar to IP, IPX static routes tell the Prestige how to reach servers beyond a remote node before a connection to that remote node is established. From Menu 12, select two, then select one of the IPX Static Routes to open Menu 12.2.1 - Edit IPX Static Route, as shown below.

  • Page 101: Table 6-3 Edit Ipx Static Route Menu Fields

    These two fields have the same meaning as those in the Ethernet setup. Tick Count Once you have completed filling in the menu, press [Enter] at the message [Press ENTER to Confirm…] to save your configuration, or press [Esc] to cancel to cancel. IPX Configuration Prestige 128IMH ISDN Modem/ Router/Hub 6-11...

  • Page 103: Bridging Setup

    Basically, all non-local packets are bridged to the WAN; however, your Prestige applies special handling for certain IPX packets to reduce the number of calls, depending on the setting of the Handle IPX field. Bridge Setup Prestige 128IMH ISDN Modem/ Router/Hub Chapter 7 Bridging Setup...

  • Page 104: Figure 7-1 Menu 3.5 - Bridge Ethernet Setup

    Prestige 128IMH ISDN Modem/ Router/Hub From Menu 3 - Ethernet Setup, enter option Bridge Setup and Menu 3.5 - Bridge Ethernet Setup displays as shown below. Press Space Bar to Toggle. Figure 7-1 Menu 3.5 - Bridge Ethernet Setup The following table describes how to configure the Handle IPX field in Menu 3.5.

  • Page 105: Figure 7-2 Menu 11.3 - Remote Node Bridging Options

    Rem LAN Net #= 00000000 My WAN Net #= 00000000 Hop Count= 1 Tick Count= 2 W/D Spoofing(min)= 3 SAP/RIP Timeout(min)= 3 Bridge Options: Dial-On-Broadcast= No Ethernet Addr Timeout(min)= 0 Enter here to CONFIRM or ESC to CANCEL: Prestige 128IMH ISDN Modem/ Router/Hub...

  • Page 106: Table 7-2 Remote Node Network Layers Menu Bridge Options

    Prestige 128IMH ISDN Modem/ Router/Hub The following table describes the bridging-specific parameters in the Remote Node Profile and Network Layers menus. Table 7-2 Remote Node Network Layers Menu Bridge Options Field Bridge Edit IP/IPX/Bridge Dial-On-Broadcast Ethernet Addr Timeout (min) Once you have completed filling in the Network Layer Options Menu, press [Enter] to return to Menu 11.1.

  • Page 107: Bridge Static Route Setup

    3 in menu 12 and then selecting one of the bridge static routes as shown below. Figure 7-3 Menu 12.3 - Bridge Static Route Setup Figure 7-4 Menu 12.3.1 - Edit Bridge Static Route Bridge Setup Prestige 128IMH ISDN Modem/ Router/Hub Menu 12.3 - Bridge Static Route Setup 1. ________ 2. ________ 3.

  • Page 108: Table 7-3 Bridge Static Route Menu Fields

    Prestige 128IMH ISDN Modem/ Router/Hub The following table describes the Bridge Static Route Menu. Table 7-3 Bridge Static Route Menu Fields Field Description Route Name Enter a name for the bridge static route for identification purposes. Active Activate/deactivate the static route.

  • Page 109: Chapter 8

    RADIUS server to provide authentication service. For details on using a RADIUS server, see the Using RADIUS Authentication section in Chapter 11 - System Security. Dial-I n Server Configuration Prestige 128IMH ISDN Modem/ Router/Hub Dial-in Server Configuration Remote Nodes Your Prestige can make calls to and receive calls from the remote node.

  • Page 110: Remote Access Server

    Prestige 128IMH ISDN Modem/ Router/Hub Remote Access Server Telecommuting enables people to work at remote sites and yet still have access to the resources in the business office. Typically, a telecommuter will use a client workstation with TCP/IP and dial - out capabilities, e.g., a Windows PC or a Macintosh. For telecommuters to call in to your Prestige, you need to configure a dial-in user profile for each telecommuter.

  • Page 111: Lan-To-Lan Server Application

    (see Chapter 5 - Remote Node Configuration). An example of your Prestige being used as a LAN-to-LAN server is shown below. Figure 8-2 Example of a LAN-to-LAN Server Application Dial-I n Server Configuration Prestige 128IMH ISDN Modem/ Router/Hub Local Network LAN-to-LAN Server...

  • Page 112: Default Dial-In Setup

    Prestige 128IMH ISDN Modem/ Router/Hub Default Dial-In Setup This section covers the default dial - in parameters. The parameters in Menu 13 affect incoming calls from both remote dial - in users, and remote nodes until authentication is completed. Once authentication is completed and if it matches a remote node, your Prestige will use parameters from that particular remote node.

  • Page 113: Table 8-2 Default Dial-In Setup Fields

    This field is applicable only if the Mutual Authen. Field is set to Yes. Enter in the login name to be used to respond to the far end’s PAP authentication request. This field does not apply to CHAP authentication. Prestige 128IMH ISDN Modem/ Router/Hub CHAP/PAP Option None...
  • Page 114 Prestige 128IMH ISDN Modem/ Router/Hub PAP Password Multiple Link Options: Max Trans Rate Callback Budget Management: Allocated Budget (min) Period (hr) IP Address Supplied By: Dial-in User IP Pool IP Pool: IP Start Addr does not apply to CHAP authentication.
  • Page 115 Note that spaces and [-] symbol, are accepted in this field. For more information on customizing your filter sets, see Chapter 9 - Filter Configuration. The default is blank, i.e., no filters. Prestige 128IMH ISDN Modem/ Router/Hub (Default = No) Default = blank 1, 2...

  • Page 116: Dial-In Users Setup

    Prestige 128IMH ISDN Modem/ Router/Hub 8.3.1 Default Dial-in Filter Use Menu 13.1 – Default Dial-in Filter and outgoing traffic between all dial - in users and your Prestige. Note that the filter set(s) only applies to the dial - in users but not the remote nodes. You can specify up to 4 filter sets separated by comma, e.g., 1, 5, 9, 12, in each of the filters field.

  • Page 117: Figure 8-6 Edit Dial-In User

    Select one of the users by number, this will bring you to Menu 14.1 - Edit Dial-in Step 2. User, as shown below. Dial-I n Server Configuration Prestige 128IMH ISDN Modem/ Router/Hub Menu 14 - Dial-in User Setup 1. johndoe 2. ________ 3.

  • Page 118: Table 8-3 Edit Dial-In User Menu Fields

    Prestige 128IMH ISDN Modem/ Router/Hub The following table provides instructions on how to fill in the Edit Dial - In User fields. Table 8-3 Edit Dial-in User Menu Fields Field Description User This is a required field. This will be used as the login name for authentication.

  • Page 119: Table 8-4 Edit Dial-In User Menu Fields (Continued)

    - in users, all usage is charged to the company instead of the Dial-I n Server Configuration Prestige 128IMH ISDN Modem/ Router/Hub ] string in Menu 2 to enable caller ID detection on the...

  • Page 120: Multiple Servers Behind Sua

    Prestige 128IMH ISDN Modem/ Router/Hub employees, and your accounting department can avoid the hassles of accountability and reimbursement. Multiple Servers behind SUA If you wish, you can make inside servers for different services, e.g., web or FTP, visible to the outside users, even though SUA makes your whole inside network appear as a single machine to the outside world.

  • Page 121: Figure 8-7 Multiple Server Configuration

    2. 0 0.0.0.0 3. 0 0.0.0.0 4. 0 0.0.0.0 5. 0 0.0.0.0 6. 0 0.0.0.0 7. 0 0.0.0.0 8. 0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Table 8-5 Services vs. Port number Prestige 128IMH ISDN Modem/ Router/Hub 8-13...
  • Page 122 Prestige 128IMH ISDN Modem/ Router/Hub Services FTP (File Transfer Protocol) Telnet SMTP (Simple Mail Transfer Protocol) DNS(Domain Name System) HTTP (Hyper Text Transfer protocol or WWW, Web) 80 PPTP (Point-to-Point Tunneling Protocol) 8-14 Port Number 1723 Dial-In Server Configuration...

  • Page 123: Chapter 9

    The Prestige 128IMH supports a comprehensive set of advanced calling features known as Supplemental Services. These features include: Call Waiting Three Way Calling (conference) Call Transfer Call Forwarding Getting Started 9.1.1 Things you need to know before you start using Supplemental Services.

  • Page 124: Setting Up Supplemental Phone Service

    Prestige 128IMH ISDN Modem/ Router/Hub Setting Up Supplemental Phone Service All Supplemental Phone Services are enabled by default except for Call Waiting, which is disabled by default but can be enabled in Menu 2.1- ISDN Advanced Setup. The Calling Line Indication, or Caller ID, also in this menu decides whether the other party can see your number when you call.

  • Page 125: Three Way Calling

    To drop the last call added to the three-way-call: Simply press the flash key. The last call that was added to the conference is dropped. To drop yourself from the conference call: Advanced Phone Services Prestige 128IMH ISDN Modem/ Router/Hub...

  • Page 126: Call Transfer

    Prestige 128IMH ISDN Modem/ Router/Hub If you hang up your telephone during a three-way-call and the two other callers remain on the line, the ISDN network will do an implicit transfer to directly connect the two remaining callers together. Call Transfer Call Transfer allows you to transfer an active call to a third party.

  • Page 127: Call Forwarding

    #21# #22# Either method should work fine, and you can use whichever one you are most comfortable with. Advanced Phone Services Prestige 128IMH ISDN Modem/ Router/Hub Table 9-1 Phone Flash Commands Meaning Activate CFB (Call Forwarding Busy) Activate CFU (Call Forwarding Unconditional)

  • Page 129: Chapter 10

    Prestige 128IMH ISDN Modem/ Router/Hub Chapter 10 Filter Configuration 10.1 About Filtering Your Prestige uses filters to decide whether or not to allow passage of a data packet and/or to make a call. There are two types of filters: data filters and call filters.

  • Page 130: Figure 10-1 Outgoing Packet Filtering Process

    Prestige 128IMH ISDN Modem/ Router/Hub Data match Outgoing Filters Packet Match Drop packet Figure 10-1 Outgoing Packet Filtering Process For incoming packets, your Prestige applies data filters only. Packets are processed depending upon whether a match is found. The following sections describe how to configure filter sets.

  • Page 131: Configuring A Filter Set

    Filter Configuration Menu 21 - Filter Set Configuration Filter Set # ------ Enter Filter Set Number to Configure= Edit Comments= Press ENTER to CONFIRM or ESC to CANCEL: Prestige 128IMH ISDN Modem/ Router/Hub Comments ------------------ ______________ ______________ ______________ ______________ ______________...

  • Page 132: Figure 10-3 Menu 21.1 - Filter Rules Summary

    Prestige 128IMH ISDN Modem/ Router/Hub # A Type - - ---- -------------------------------------------- --------- - - - Figure 10-3 Menu 21.1 - Filter Rules Summary 10.2.1 Filter Rules Summary Menu This screen shows the summary of the existing rules in the filter set. The following tables contain a brief description of the abbreviations used in Menu 21.1.

  • Page 133: Table 10-2 Abbreviations Used In The Filter Rules Summary Menu (Continued)

    Source Address Source Port number Destination Address Destination Port number Filter Configuration Prestige 128IMH ISDN Modem/ Router/Hub Display [Y] means there are more rules to check. [N] means there are no more rules to check. [F] means to forward the packet.

  • Page 134: Table 10-4 Abbreviations Used If Filter Type Is Ipx

    Prestige 128IMH ISDN Modem/ Router/Hub If the filter type is IPX, the following abbreviations listed in the following table will be used. Table 10-4 Abbreviations Used If Filter Type Is IPX Abbreviation Description IPX Packet Type Source Socket Destination Socket If the filter type is GEN (generic), the following abbreviations listed in the following table will be used.

  • Page 135: Configuring A Filter Rule

    Prestige 128IMH ISDN Modem/ Router/Hub 10.3 Configuring a Filter Rule To configure a filter rule, enter its number in Menu 21.1 - Filter Rules Summary and press Enter to open Menu 21.1.1 for the rule. There are three types of filter rules: TCP/IP, IPX and Generic. Depending on the type of rule, the parameters below the type will be different.

  • Page 136: Figure 10-4 Menu 21.1.1 - Tcp/Ip Filter Rule

    Prestige 128IMH ISDN Modem/ Router/Hub Press Space Bar to Tog gle. Figure 10-4 Menu 21.1.1 - TCP/IP Filter Rule 10-8 Menu 21.1.1 - TCP/IP Filter Rule Filter #: 1,1 Filter Type= TCP/IP Filter Rule Active= No IP Protocol= 0 IP Source Route= No...

  • Page 137: Table 10-6 Tcp/Ip Filter Rule Menu Fields

    If yes, a matching packet is passed to the next filter rule before an action is taken; else the packet is disposed of according the action fields. Filter Configuration Prestige 128IMH ISDN Modem/ Router/Hub Yes/No Yes/No IP address Subnet mask...
  • Page 138 Prestige 128IMH ISDN Modem/ Router/Hub Field Description according the action fields. If More is Yes, then Action Matched and Action Not Matched will be N/A. Select the logging option from the following: None – No packets will be logged. Action Matched - Only packets that match the rule parameters will be logged.

  • Page 139: Figure 10-5 Menu 21.1.2 - Generic Filter Rule

    To configure a generic rule, select Generic Filter Rule in the Filter Type field and press Enter to open Menu 21.1.2 - Generic Filter Rule, as shown below. Figure 10-5 Menu 21.1.2 - Generic Filter Rule Filter Configuration Prestige 128IMH ISDN Modem/ Router/Hub Menu 21.1.2 - Generic Filter Rule Filter #: 1,1 Filter Type= Generic Filter Rule...

  • Page 140: Table 10-7 Generic Filter Rule Menu Fields

    Prestige 128IMH ISDN Modem/ Router/Hub The table below describes the fields in the Generic Filter Rule Menu. Table 10-7 Generic Filter Rule Menu Fields Field Description Offset Enter the starting byte of the data portion in the packet that you wish to compare.

  • Page 141: Novell Ipx Filter Rule

    Socket # Comp= None Operation= N/A More= No Log= None Action Matched= Check Next Rule Action Not Matched= Check Next Rule Press ENTER to Confirm or ESC to Cancel: Figure 10-6 Menu 21.1.3 - IPX Filter Rule Prestige 128IMH ISDN Modem/ Router/Hub 10-13...

  • Page 142: Table 10-8 Ipx Filter Rule Menu Fields

    Prestige 128IMH ISDN Modem/ Router/Hub The table below describes the IPX Filter Rule. Field IPX Packet Type Destination/Source Network # Destination/Source Node # Destination/Source Socket # Destination/Source Socket # Comp Operation Once you have completed filling in Menu 21.1.3 - IPX Filter Rule, press [Enter] at the message [Press Enter to Confirm] to save your configuration, or press [Esc] to cancel.

  • Page 143: Chapter 11

    - SNMP Configuration, as shown in the figure below. The “community” for Get, Set and Trap fields is simply SNMP’s terminology for password. Figure 11-1 Menu 22 - SNMP Configuration SNMP Configuration Prestige 128IMH ISDN Modem/ Router/Hub SNMP Configuration Menu 22 - SNMP Configuration SNMP:...

  • Page 144: Table 11-1 Snmp Configuration Menu Fields

    Prestige 128IMH ISDN Modem/ Router/Hub The following table describes the SNMP configuration parameters. Table 11-1 SNMP Configuration Menu Fields Field Description Get Community Enter the get community, which is the password for the incoming Get- and GetNext- requests from the management station.

  • Page 145: Chapter 12

    Step 1. Security as shown below. System Security Menu 23 - System Security 1. Change Password 2. External Server Enter Menu Selection Number: 1 Figure 12-1 Menu 23 - System Security Prestige 128IMH ISDN Modem/ Router/Hub Chapter 12 System Security 12-1...

  • Page 146: Figure 12-2 Menu 23.1 - System Security - Change Password

    Prestige 128IMH ISDN Modem/ Router/Hub From the System Security Menu, select option Change Password to open Menu Step 2. 23.1 - System Security - Change Password. Enter your existing system password and press [Enter]. Step 3. Figure 12-2 Menu 23.1 - System Security - Change Password Enter your new system password and press [Enter].

  • Page 147: Using Radius Authentication

    VALUE Zyxel-Callback-Phone-Source VALUE Zyxel-Callback-Phone-Source These changes add the support for CLID authentication, as described in the section below. System Security Prestige 128IMH ISDN Modem/ Router/Hub ). Using any text editor, add the following lines to /etc/raddb integer None Optional Mandatory...
  • Page 148 Prestige 128IMH ISDN Modem/ Router/Hub 12-4 System Security...

  • Page 149: Figure 12-3 Menu 23.2 - System Security - External Server

    System Security - External Server, shown below. Press Space Bar to Toggle. Figure 12-3 Menu 23.2 - System Security - External Server System Security Prestige 128IMH ISDN Modem/ Router/Hub Menu 23.2 - System Security - External Server Authentication Server: Active= No...

  • Page 150: Table 12-1 System Security - External Server Menu Fields

    Prestige 128IMH ISDN Modem/ Router/Hub The fields in the System Security - External Server Menu are listed in the following table. Table 12-1 System Security - External Server Menu Fields Field Description Active Determines whether the external security facility is enabled.

  • Page 151: Using Radius Authentication For Clid

    Prestige 128IMH ISDN Modem/ Router/Hub 12.2.5 Using RADIUS Authentication for CLID To use RADIUS for CLID authentication, create a user record in the file where the user users name (the first field) is the telephone number, and the password (the second field) is always (case-sensitive).

  • Page 153: Chapter 13

    Prestige 128IMH ISDN Modem/ Router/Hub Chapter 13 Telnet Configuration and Capabilities 13.1 About Telnet Configuration Before the Prestige is properly setup for TCP/IP, the only option for configuring it is through the console port. Once your Prestige is configured, you can use telnet to configure it remotely as shown below.

  • Page 154: Telnet Under Sua

    Prestige 128IMH ISDN Modem/ Router/Hub 13.2 Telnet Under SUA When Single User Account (SUA) is enabled and an inside server is specified, telnet connections from the outside will be forwarded to the inside server. So to configure the Prestige via telnet from the outside, you must first telnet to the inside server, and then telnet from the server to the Prestige using its inside LAN IP address.

  • Page 155: Chapter 14

    Select menu 24 in the main menu to open Menu 24 - System Maintenance, as shown below. Figure 14-1 Menu 24 - System Maintenance System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub System Maintenance Menu 24 - System Maintenance System Status...

  • Page 156: System Status

    Prestige 128IMH ISDN Modem/ Router/Hub 14.1 System Status The first selection, System Status, gives you information on the version of your system firmware and the status and statistics of the ports, as shown in below. System Status is a tool that can be used to monitor your Prestige.

  • Page 157: Table 14-1 System Maintenance - Status Menu Fields

    Shows the current transmission speed and mode of the LAN. TX Pkt The number of transmitted packets to LAN. RX Pkt The number of received packets from LAN. Collision Number of collisions. System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub 14-3...

  • Page 158: Figure 14-3 Lan Packet That Triggered Last Call

    Prestige 128IMH ISDN Modem/ Router/Hub CHAN 1 IP Addr Refers to the IP address of the Prestige on Channel 1. CHAN 2 IP Addr Refers to the IP address of the Prestige on Channel 2. Port 1 CLID Shows the Caller ID of the peer on Port 1.

  • Page 159: Figure 14-4 System Maintenance - Information

    14.1.1 System Information Figure 14-4 System Maintenance - Information System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub Menu 24.2.1 – System Maintenance - Information Name: Routing: IP RAS S/W Version: V2.21B01 | 11/6/98 ISDN F/W Version: V 099 Country Code: 238 Ethernet Address:00:a0:c5:02:34:56 IP Address: 192.168.1.1...

  • Page 160: Console Port Speed

    Prestige 128IMH ISDN Modem/ Router/Hub Table 14-2 Fields in System Maintenance Field Description Name displays the system name of your Prestige. This information can be modified in Menu 1 - General Setup. Routing refers to the routing protocol used. RAS S/W refers to the version of the ZyNOS software.

  • Page 161: Log And Trace

    After the Prestige finishes displaying, you will have the option to clear the error log. System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub Console Port Speed: 115200 Press ENTER to Confirm or ESC to Cancel:...

  • Page 162: Figure 14-6 Examples Of Error And Information Messages

    Prestige 128IMH ISDN Modem/ Router/Hub Examples of typical error and information messages are presented in the figure below. 4 PP07 4 PINI e PINI Clear Error Log (y/n): Figure 14-6 Examples of Error and Information Messages 14-8 INFO LAN promiscuous mode <0>...

  • Page 163: Figure 14-7 Menu 24.3.2 - System Maintenance - Syslog And Accounting

    Your Prestige sends three types of syslog messages: call information messages (i.e. CDR), error information messages and session information messages. Some examples of these syslog messages are shown below: System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub Syslog: Active= No Syslog IP Address= ?
  • Page 164 Prestige 128IMH ISDN Modem/ Router/Hub 1. Call Information Messages: line 1 channel 1, call 41, C01, Incoming Call, 40001 line 1 channel 1, call 41, C01, ANSWER Connected, 49K 40001 line 1 channel 1, call 41, C01, Incoming Call, Call Terminated 2.

  • Page 165: Diagnostic

    From this menu, select option 4. Diagnostic. This will open Menu 24.4 - System Step 2. Maintenance - Diagnostic. System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub Menu 24.4 - System Maintenance - Diagnostic System 21. Reboot System 22. Command Mode...

  • Page 166: Table 14-4 System Maintenance Menu Diagnostic

    Prestige 128IMH ISDN Modem/ Router/Hub The following table describes the diagnostic tests available in Menu 24.4 for your Prestige and the connections. Table 14-4 System Maintenance Menu Diagnostic Field Description Hang Up B1 Call This tool hangs up the B1 channel. This is only applicable if the B1 channel is currently in use.

  • Page 167: Figure 14-9 Trace Display For A Successful Manual Call

    Call CONNECT speed<64000> chan<2> prot<1> LCP up CHAP send response ***Login to remote failed. Check name/passwd. Receive Terminal REQ IPCP down Line Down chan<2> Figure 14-10 Trace Display for a Failed Authentication System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub 14-13...

  • Page 168: Backup Configuration

    Prestige 128IMH ISDN Modem/ Router/Hub 14.4 Backup Configuration Option 5 from Menu 24 - System Maintenance allows you to backup the current Prestige configuration to your workstation. Backup is highly recommended once your Prestige is functioning properly. You must perform the backup and restore through the console port. Any serial communications program should work fine;...

  • Page 169: Figure 14-11 Menu 24.7 - System Maintenance - Upload Firmware

    4. After successful firmware upload, enter "atgo" to restart the router. Warning: Proceeding with the upload will erase the current router firmware. Figure 14-12 Menu 24.7.1 - Uploading Router Firmware System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub Do You Wish To Proceed:(Y/N) 14-15...

  • Page 170: Uploading Router Configuration File

    Prestige 128IMH ISDN Modem/ Router/Hub 14.6.2 Uploading Router Configuration File The configuration data, system-related data, the error log and the trace log are all stored in the configuration file. Please be aware that uploading the configuration file replaces everything contained within.

  • Page 171: Figure 14-13 Menu 24.7.2 - System Maintenance - Upload Router Configuration File

    Step 1. Use telnet from your workstation to connect to the Prestige and log in. Because TFTP does not have any security check, the Prestige records the IP address of the telnet client and accepts TFTP requests only from this address. System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub Do You Which To Proceed:(Y/N) 14-17...

  • Page 172: Boot Module Commands

    Prestige 128IMH ISDN Modem/ Router/Hub Step 2. Put the SMT in command interpreter (CI) mode by entering 8 in Menu 24 – System Maintenance. Step 3. Enter command “sys stdio 0” to disable SMT timeout, so the TFTP transfer will not be interrupted.

  • Page 173: Figure 14-14 Boot Module Commands

    System Maintenance print help boot system upload RAS code upload RAS configuration file change baud rate. 1:38.4,2:19.2,3:9.6,4:57.6,5:115.2 download configuration to PC display seed for password generation display Revision and etc Figure 14-14 Boot module commands Prestige 128IMH ISDN Modem/ Router/Hub 14-19...

  • Page 174: Command Interpreter Mode

    This option allows you to enter the command interpreter mode. A list of valid commands can be found by typing [help] at the command prompt. For more detailed information, check the ZyXEL Copyright (c) 1994 - 1998 ZyXEL Communications Corp. ras> ?

  • Page 175: Figure 14-16 Menu 24.9 - System Maintenance - Call Control

    Call Control Parameters Blacklist Budget Management Call History Enter Menu Selection Number: Menu 24.9.1 - Call Control Parameters Dialer Timeout: Digital Call(sec)= 30 Retry Counter= 0 Retry Interval(sec)= N/A Figure 14-17 Call Control Parameters Prestige 128IMH ISDN Modem/ Router/Hub 14-21...
  • Page 176 Prestige 128IMH ISDN Modem/ Router/Hub Table 14-5 Call Control Parameters Fields Field Dialer Timeout: Digital Call (sec) Retry Counter Retry Interval (sec) 14.8.2 Blacklist The phone numbers on the bla cklist are numbers that the Prestige had problems connecting in the past.

  • Page 177: Figure 14-18 Menu 24.9.2 - Blacklist

    Prestige 128IMH ISDN Modem/ Router/Hub Figure 14-18 Menu 24.9.2 - Blacklist System Maintenance 14-23...

  • Page 178: Figure 14-19 Menu 24.9.3 - Budget Management

    Prestige 128IMH ISDN Modem/ Router/Hub 14.8.3 Budget Management Menu 24.9.3 shows the budget management statistics for outgoing calls. Remote Node 1. isp1 2. -------- 3. -------- 4. -------- 5. -------- 6. -------- 7. -------- 8. -------- 9. -------- 10. -------- 11.

  • Page 179: Figure 14-20 Call History

    This is the telephone number of past incoming and outgoing calls. This shows whether the call was incoming or outgoing. Rate This is the transfer rate of the call. System Maintenance Prestige 128IMH ISDN Modem/ Router/Hub Menu 24.9.4 - Call History Rate #call Figure 14-20 Call History...
  • Page 180 Prestige 128IMH ISDN Modem/ Router/Hub #call This is the number of calls made to or received from that telephone number. This is the length of time of the longest telephone call. This is the length of time of the shortest telephone call.

  • Page 181: Chapter 15

    Prestige Cannot access the Prestige via the console port. Troubleshooting Prestige 128IMH ISDN Modem/ Router/Hub Corrective Action Check the connection between the AC adapter and the Prestige. If the error persists, you may have a hardware problem. In this case you should contact technical support.

  • Page 182: Problems With The Isdn Line

    Prestige 128IMH ISDN Modem/ Router/Hub 15.2 Problems With the ISDN Line Table 15-2 Troubleshooting the ISDN Line Problem The ISDN initialization failed. This problem occurs when you attempt to save the parameters entered in menu 2, but receive the message, ‘Save successful, but Failed to initialize ISDN;...

  • Page 183: Problems With The Lan Interface

    Problem A remote user cannot dial-in Troubleshooting Prestige 128IMH ISDN Modem/ Router/Hub Corrective Action Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a station connected. If it is off, check the cables between your Prestige and the station.
  • Page 184 Prestige 128IMH ISDN Modem/ Router/Hub 15-4 If the remote dial-in user is negotiating IPX, verify that the IPX network number is valid from the IPX pool (if it is being used). Troubleshooting...

  • Page 185: Isdn Information Worksheet

    ISDN Data Number & Subaddress A/B 1 Number & Subaddress A/B 2 Number & Subaddress Worksheet Prestige 128IMH ISDN Modem/ Router/Hub ISDN Information Worksheet General Setup Information q TCP/IP ISDN Setup Information q AT&T 5ESS Point to Point q Northern Telecom NI-1 q AT&T 5ESS NI-1...
  • Page 186 Prestige 128IMH ISDN Modem/ Router/Hub Subaddress Outside Line Prefix PABX # (S/T bus) Incoming Number Matching Analog Call Routing Global Analog Call Ethernet Interface IP Address IP Subnet Mask q MSN q CDSA q A/B #1 q A/B #2 q Accept...

  • Page 187: Acronyms And Abbreviations

    Integrated Service Digital Network Internet Service Provider Local Area Network Media Access Control (PPP) Multilink Protocol Network Address Translation Password Authentication Protocol POTS Plain Old Telephone Service Point to Point Protocol Acronyms and Abbreviations Prestige 128IMH ISDN Modem/ Router/Hub Acronyms and Abbreviations...
  • Page 188 Prestige 128IMH ISDN Modem/ Router/Hub PSTN Public Switched Telephone Network RADIUS Remote Authentication Dial-In User Service Routing Infor mation Protocol (IPX) Service Advertising Protocol SNAP Sub-Network Access Protocol SNMP Simple Network Management Protocol Single User Account (ISDN) Terminal Adapter TFTP...

  • Page 189: Index

    4-4, 7-11 BTR. See Base Transmission Rate budget, 8-6, 14-23 call control, 14-20 call direction, 4-2 Index Prestige 128IMH ISDN Modem/ Router/Hub callback, 4-3, 8-6, 8-10, 8-11 CHAP, 4-4 CLID, 4-3, 8-5, 8-11 community, 11-19 console port, 2-10 contact person, 2-17...
  • Page 190 Prestige 128IMH ISDN Modem/ Router/Hub frame type, 6-1, 6-5 gateway, 5-7, 6-10, 7-16 General Setup, 2-16 generic filter rule, 10-15 hop count, 6-10 IANA, 3-2 idle timeout, 4-5 Internet access, 1-4, 3-1 IP address, 3-2, 3-6, 4-4, 5-4, 5-6, 7-16, 8-6...
  • Page 191 SNAP, 6-1 SNMP, 11-19 socket, 6-10 software update, 14-15 SUA, 1-5, 3-10, 5-4 Index Prestige 128IMH ISDN Modem/ Router/Hub subnet mask, 3-2, 3-6, 5-4, 5-7 switch types, xxi, 15-26 syslog, 14-9 system name, 2-17 system status, 14-2 Target Utility, 4-7...

This manual is also suitable for:

P-128P-128imhP-128mh

Table of Contents