Table Of Contents - Panasonic KX-TG5631S Service Manual

KX-TG5631S / KX-TG5632M / KX-TG5633B / KX-TGA560S / KX-TGA560M / KX-TGA560B
Note:
Because CONTENTS 4 is the extract from the Operating Instructions of this model, it is subject to change without notice. You can
download and refer to the original Operating Instructions on TSN Server for further information.
CONTENTS
1 ABOUT LEAD FREE SOLDER (PbF: Pb free)
1.1. Suggested PbF Solder
1.2. How to Recognize that Pb Free Solder is Used
2 FOR SERVICE TECHNICIANS
3 CAUTION
4 OPERATING INSTRUCTIONS
4.1. Battery
4.2. Location of Controls
4.3. Displays
4.4. Settings
4.5. Troubleshooting
5 DISASSEMBLY INSTRUCTIONS
5.1. Base Unit
5.2. Handset
5.3. Charger Unit
6 HOW TO REPLACE THE HANDSET LCD
7 TROUBLESHOOTING GUIDE
7.1. Check Power
7.2. Error Message Table
7.3. Check Record
7.4. Check Playback
7.5. Check Battery Charge
7.6. Check Link
7.7. Check the RF part
7.8. Check Handset Transmission
7.9. Check Handset Reception
7.10. Check Caller ID
8 ADJUSTMENT AND TEST MODE
8.1. Test Mode Flow Chart for Base Unit
8.2. Test Mode Flow Chart for Handset
8.3. X501 (Base Unit), X201 (Handset) Check
8.4. Adjust Battery Low Detector Voltage (Handset)
8.5. Base Unit Reference Drawing
8.6. Handset Reference Drawing
8.7. Frequency Table
8.8. How to Clear User Setting
Page
4 9 DESCRIPTION
4 9.1. Frequency
5 9.2. FHSS (Frequency Hopping Spread Spectrum)
6 9.3. Signal Flowchart in the Whole System
6 10 EXPLANATION OF LINK DATA COMMUNICATION
7 10.1. Calling
7 10.2. To Terminate Communication
9 10.3. Ringing
11 11 BLOCK DIAGRAM (BASE UNIT_MAIN)
13 12 CIRCUIT OPERATION (BASE UNIT_MAIN)
18 12.1. DSP (Digital Speech/Signal Processing: IC501)
21 12.2. Flash Memory (IC601)
21 12.3. Power Supply Circuit
22 12.4. Reset Circuit
23 12.5. Telephone Line Interface
24 12.6. Auto Disconnect Circuit
25 12.7. Parallel Connection Detect Circuit
26 12.8. Calling Line Identification (Caller ID)/Call Waiting Caller ID
26
27 13 BLOCK DIAGRAM (BASE UNIT_RF PART)
28 14 BLOCK DIAGRAM (HANDSET_RF PART)
28 15 CIRCUIT OPERATION (RF PART)
29 15.1. Power Supply Circuit
30 15.2. 2.4GHz Mod/Demod Circuit
37 15.3. 5.8GHz Converter Circuit
37 15.4. 5.8GHz PA (Power Amplifier), 5.8GHz LNA (Low Noise
37 Amplifier) and Antenna Switch Circuit
38 16 BLOCK DIAGRAM (HANDSET)
38 17 CIRCUIT OPERATION (HANDSET)
42 17.1. Construction
46 17.2. Power Supply Circuit
46 17.3. Charge Circuit
47 17.4. Ringer and Handset SP-Phone
48 17.5. Sending Signal
49 17.6. Reception Signal
51 18 CIRCUIT OPERATION (CHARGER UNIT)
2
Page
52
52
52
54
55
55
55
55
56
57
57
57
58
60
61
62
63
64
66
67
68
69
70
71
72
73
74
74
75
76
76
77
77
78