Nomenclature; Heat Pump; Features And Benefits - York AFFINITY R-410A Technical Manual

R-410a affinity series bhx and bhz models 2 - 5 ton 60 hertz
Hide thumbs Also See for AFFINITY R-410A:
Table of Contents

Advertisement

Nomenclature

Heat Pump

Product Category
B = Single Package Heat Pumps
(Air Cooled)

Features and Benefits

Standard Features
• Operating Efficiency - All heat pump units provide
operating efficiencies of 13 to 15 SEER and 7.7 to 8.0
HSPF. All efficiencies exceed legislated minimum levels.
• On Site Flexibility - All model sizes share a common,
compact design cabinet in a single footprint. The installer
has the flexibility of setting one curb and placing the
proper tonnage unit on that curb after the internal load has
been determined. Field convertible duct connections from
side shot to down shot allows the installer to have greater
flexibility with less inventory.
• Lower Installation Cost - Installation time and costs are
reduced by easy power and control wiring connections.
The small base dimension means less space is required
on the ground or roof, plus, the installer can fit this unit
between the wheel wells of full size pick-up truck.
• All units are completely wired, charged with R-410A and
tested prior to shipment. Unique test stations using a new
state of the art computerized process system are used to
insure product quality. Refrigerant charge and component
part numbers are verified via computers at assembly. Vital
run test statistics such as system pressure, motor
currents, air velocity and temperature, unit vibration, and
gas system safeties are monitored and recorded by the
system to insure unit performance.
• Equal size, side supply and return duct connections
allows easy hook-up of ducts to match low crawl spaces
without transition pieces.
• Utility Connections Made Easy - Electric utility
knockouts are provided through the bottom as well as the
side of the unit. Utility connections can be made quickly
and with a minimum amount of field labor. A field supplied
and field installed electrical disconnect switch must be
installed.
Johnson Controls Unitary Products
B 1
Product Generation
1 = New or Current Design
2 = 2nd Generation
Product Identifier
HZ = R-410A 13 SEER
HX = R-410A 15 SEER
HZ
024
A
06
Factory Installed Electric Heat
A = No Electric Heat Installed
Nominal Cooling Capacity (MBH)
024 = 24,000 BTUH
042 = 42,000 BTUH
030 = 30,000 BTUH
048 = 48,000 BTUH
036 = 36,000 BTUH
060 = 60,000 BTUH
• Convertible Airflow Design - The bottom duct openings
are covered when they leave the factory ready to be used
for a side supply/side return application. If a bottom
supply/bottom return application is desired, you simply
remove the two panels from the bottom of the unit and
place them in the side supply/side return duct openings.
No panel cutting is required and no accessory panel is
necessary. Convertible airflow design allows maximum
field flexibility and minimum inventory.
• Condensate Pan - A non-corrosive, long-lasting, water-
tight pan is positioned below the evaporator coil to collect
and drain all condensate. Less collection of stagnate
condensate will build-up. The condensate pan conforms
to ASHRAE 62-89 standards (Ventilation for Acceptable
Indoor Air Quality).
• Condensate Drain - The 3/4 inch NPTF connection is
rigidly mounted to assure proper fit and leak tight seal.
• Durable Finish - With a heavy duty cabinet made of
powder-painted, galvanized steel the neutral color blends
into surrounding areas. The powdered paint provides a
better paint to steel bond, which resists corrosion and rust
creep. The special primer formulas and glossy finish
insures less fading when exposed to sunlight and offers a
more attractive on site appearance. This paint finish
meets ASTM-B117 standards for 1000 hours salt spray
rating. The highest in the industry.
• Full Perimeter Base Rails - The easily removable base
rails provide a solid foundation for the entire unit and
protects the unit during shipment. The rails provide fork lift
access from all sides, and rigging holes are also provided
so that an overhead crane can be used to place the units
on a roof. On applications where the unit is placed on a
pad, the base will keep the unit off the pad to deter
corrosion. On applications where height is limited, the inch
high base rails may be removed on location.
333495-YTG-C-0908
Voltage Code
06 = 208/230-1-60
25 = 208/230-3-60
46 = 460-3-60
3

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents