KTM 450 SX ATV 2009 Setup Instructions
  1. Manuals
  2. Brands
  3. KTM Manuals
  4. Offroad Vehicle
  5. 450 SX ATV 2009
  6. Setup instructions

KTM 450 SX ATV 2009 Setup Instructions

Hide thumbs
Table of Contents

Advertisement

Quick Links

SETUP INSTRUCTIONS
2009
450 SX ATV
505 SX ATV
ART. NO. 3211428en

Advertisement

Table of Contents
loading

Related Manuals for KTM 450 SX ATV 2009

Summary of Contents for KTM 450 SX ATV 2009

  • Page 1 SETUP INSTRUCTIONS 2009 450 SX ATV 505 SX ATV ART. NO. 3211428en...
  • Page 3 KTM accepts no liability for delivery options, deviations from illustrations and descriptions, as well as misprints and other errors.

  • Page 4: Means Of Representation

    MEANS OF REPRESENTATION Symbols used The symbols used are explained in the following. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). Identifies a page reference (more information is provided on the specified page). Formats used The typographical and other formats used are explained in the following.
  • Page 5   Info The key cover cap is in the tool set. Read the installation instructions on the inside of the cap. – Print out the current PDI form found on KTM DEALER.NET and perform the delivery inspection. 100107-10...

  • Page 6: Adjusting The Handlebar Position

    WORK Adjusting the handlebar position – Pull the instrument support off the handlebar and swing it to the side. Info Protect the vehicle and its attachments from damage by covering them. Do not bend the cables and lines. 100100-10 – Remove the four screws .

  • Page 7: Mounting The Seat

    WORK Mounting the seat – Hook slot on the seat into collar sleeve of the fuel tank, lower the rear of the   seat and slide tab under fuel tank   100046-10 – Push down the rear of the seat until release hook engages.

  • Page 8: Installing The Rear Fender

    WORK Installing the rear fender – Raise the rear of air filter box lid . At the same time, use your other hand to press  on the carburetor connection boot to kink it at that location. This prevents the car- buretor connection boot from disconnecting from the carburetor.

  • Page 9: Installing The Battery

    WORK – Switch off all power-consuming components and switch off the engine. – Remove the rear fender. ( p. 5) – Disconnect the minus (negative) cable of the battery to avoid damage to the vehi- cle's electronics. – Connect the battery charger to the battery. Switch on the battery charger. Battery charger (58429074000) You can also use the battery charger to test rest potential and start potential of the battery, and to test the generator.
  • Page 10 WORK Refueling 3.10 Danger Fire hazard Fuel can easily catch fire. – Never fill up the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately. –...

  • Page 11: Technical Data - Tightening Torques For Chassis

    TECHNICAL DATA - TIGHTENING TORQUES FOR CHASSIS – Remaining nuts, chassis 15 Nm (11.1 lbf ft) – Remaining screws, chassis 10 Nm (7.4 lbf ft) – Screw on fuel tank 6 Nm (4.4 lbf ft) – Screw, clamping nut, rear axle 10 Nm (7.4 lbf ft) ®...
  • Page 12 SUBSTANCES Super unleaded (ROZ 95 / RON 95 / PON 91) According to – DIN EN 228 (ROZ 95 / RON 95 / PON 91)
  • Page 13 *3211428en* 3211428en KTM-Sportmotorcycle AG 5230 Mattighofen/Austria http://www.ktm.com...

This manual is also suitable for:

505 sx atv 2009

Table of Contents