Recording - Yamaha RX-V2400 Owner's Manual

RECORDING

You can use the REC OUT/ZONE 2 or REC OUT control
to record one source while watching and/or listening to
another source.
Recording adjustments and other operations are
performed from the recording components. Refer to the
operation instructions for those components.
INPUT
STANDBY
/ON
SOURCE PRESET/
/REMOTE A/B/C/D/E TUNING
DVD MD/TAPE
D–TV CD–R
SPEAKERS MULTI CH INPUT MODE CBL/SAT TUNER
INPUT
A B
VCR 1 CD
/VCR2
REC OUT /ZONE 2 OPTIMIZER
MIC
1 2
1
Turn on the power of this unit and all
connected components.
2
Select the source component you want to
record from by using REC OUT/ZONE 2 or
REC OUT.
• To record the current input source that you are
watching or listening to, set REC OUT/ZONE 2 or
REC OUT to SOURCE/REMOTE.
DVD
DTV
CBL/SAT
VCR 1
DVR
/VCR2
REC OUT/ZONE 2
• To record a source other than the one that you are
watching or listening to, set REC OUT/ZONE 2 or
REC OUT to the source you want to record.
DTV
CBL/SAT
VCR 1
DVR
/VCR2
REC OUT/ZONE 2
After this setting, you can change the source you
are listening to and/or watching without effecting
the recording by rotating INPUT (or pressing one
of the input selector buttons on the remote control).
Note
The source you record and the source sent to Zone 2 (U.S.A.,
Canada and Australia models only) are always the same.
40
RECORDING
VOLUME
PRESET TUNING RDS MODE
/TUNING FM/AM MEMORY MODE /FREQ EON PTY SEEK
PROGRAM
EDIT MAN'L/AUTO FM AUTO/MAN'L MONO MODE START TONE CONTROL
PHONES S VIDEO VIDEO L AUDIO R OPTICAL
SILENT VIDEO AUX
(U.S.A. model)
SOURCE
/REMOTE
MD/TAPE
CD-R
TUNER
CD
SOURCE
/REMOTE
DVD MD/TAPE
CD-R
TUNER
CD
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
y
To record audio and video from different sources, set REC OUT/
ZONE 2 or REC OUT to SOURCE/REMOTE, select a video
source first then select an audio source (see page 31).
Notes
STRAIGHT
EFFECT • Do a test recording before you start an actual recording.
• When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
• The setting of TONE CONTROL, VOLUME, "Speaker level"
(page 50) and programs does not affect the recorded material.
• A source connected to the MULTI CH INPUT jacks of this unit
cannot be recorded.
• S-video and composite video signals pass independently
through this unit's video circuits. Therefore, when recording or
dubbing video signals, if your video source component is
connected to provide only an S-video (or only a composite
video) signal, you can record only an S-video (or only a
composite video) signal to your VCR.
• A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR 1 IN is not
output on VCR 1 OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material may
infringe copyright laws.
If you playback a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.
Special considerations when recording
DTS software
The DTS signal is a digital bit stream. Attempting to
digitally record the DTS bit stream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
For LDs, DVDs and CDs encoded with DTS, when your
player is compatible with the DTS format, follow its
operation instruction to make a setting so that the analog
signal will be output from the player.