Yamaha PLG100-XG Owner's Manual page 27

Yamaha plug-in board owner's manual

Hide thumbs

Table Of Contents

Table of Contents

1.2.12 Harmonic Content

This message adjusts the resonance of the ﬁlter that is speciﬁed for the sound.

Control# Parameter

Harmonic Content

Since this is a relative change parameter, it speciﬁes a boost or cut relative to

64.

Higher values will produce a more distinctive sound.

For some sounds, the effective range may be less than the possible range of

settings.

1.2.13 Release Time

This message adjusts the EG release time that was speciﬁed by the sound data.

Control# Parameter

Release Time

Since this is a relative change parameter, it speciﬁes an increase or decrease

relative to 64.

Increasing this value will lengthen the release that follows a note-off.

1.2.14 Attack Time

This message adjusts the EG attack time that was speciﬁed by the sound data.

Control# Parameter

Attack Time

Since this a relative change parameter, it speciﬁes an increase or decrease rela-

tive to 64.

Increasing this value will make the attack more gradual, and decreasing this

value will make the attack sharper.

1.2.15 Brightness

This message adjusts the cutoff frequency of the low pass ﬁlter speciﬁed by the

sound data.

Control# Parameter

Brightness

Since this is a relative change parameter, it speciﬁes an increase or decrease

relative to 64.

Lower values will produce a more mellow sound.

For some sounds, the effective range may be less than the possible range of

settings.

1.2.16 Portamento Control

This message speciﬁes the portamento source key number (the key number at

which portamento will begin).

Data of 0...127 speciﬁes the portamento source key.

When Portamento Control is received, the currently-sounding pitch will

change at a Portamento Time of 0 to the key of the next-received note-on of the

same channel.

Control# Parameter

Portamento Control

This is received even if Rcv PORTAMENTO = OFF.

1.2.17 Effect1 Depth(Reverb Send Level)

This message speciﬁes the send level for the reverb effect.

Control# Parameter

Effect1 Depth

Increasing this value will produce a richer reverb. The effect of the value will

depend on the state of the reverb effect.

1.2.18 Effect3 Depth(Chorus Send Level)

This message speciﬁes the send level for the chorus effect.

Control# Parameter

Effect3 Depth

Raising this value will increase the modulation or spaciousness. The effect of

the value will depend on the state of the chorus effect.

1.2.19 Effect4 Depth (Variation Effect Send Level)

This message speciﬁes the send level for the variation effect.

Control# Parameter

Effect4 Depth

However, this is not received if the Variation Effect parameter Variation Con-

nection = 0 (Insertion).

Data Range

0...64...127 (-64...0...+63)

Data Range

0...64...127 (-64...0...+63)

Data Range

0...64...127 (-64...0...+63)

Data Range

0...64...127 (-64...0...+63)

Data Range

0...127 (C-2...G8)

Data Range

0...127

Data Range

0...127

Data Range

0...127

1.2.20 Data Increment/Decrement (for RPN)

This message increases or decreases the parameter value speciﬁed for RPN

(see 1.2.22), by increments of 1.

Control# Parameter

RPN Increment

RPN Decrement

The data byte is ignored.

1.2.21 NRPN (Non-registered parameter number)

This message is used to specify a sound parameter (such as vibrato, ﬁlter, EG,

drum setup etc.) as an offset value.

Use NRPN MSB and NRPN LSB to specify the parameter that you wish to

modify, and then use Data Entry (see 1.2.4) to set the value for the speciﬁed

parameter.

Control# Parameter

NRPN LSB

NRPN MSB

If the Multi Part parameter Rcv NRPN = OFF, that part will not receive NRPN.

The following NRPN messages can be received.

NRPN

Data Entry *1

MSB LSB

-- *2

Vibrato rate