Installer Configuration Menu - White Rodgers 1F95-1271 Installation And Operating Instructions Manual

INSTALLER/CONFIGURATION MENU
To enter the menu: Press the Menu button. Press and hold for 5 seconds the Installer Config button. This displays menu
item #1 in the table below. Press
to change a menu item.
Non-
Menu
Reference Program- Program-
mable mable
Number
1 1
1
2 2 2
3 3 3
4 * NA
4
5 4
5
6 6 * NA
7 7 5
8 6
8
9 7
9
10 10 8
11 11 9
12 12 10
13 11
13
14 14 12
15 15 13
16 14
16
17 17 15
18 16
18
19 19 17
20 18
20
21 19
21
22 20
22
* Not Applicable
1) This control can be configured for:
MS2 – Multi-Stage System (no heat pump)
HP1 – Heat Pump with one stage of compressor
HP2 – Heat Pump with two stage compressor or two
compressor system, Gas or Electric backup
SS1 – Single Stage System
2) GAS or Electric (ELE) fan operation. If the heating system
requires the thermostat to energize the fan, select ELE.
Select GAS if the heating system energizes the fan on a
call for heat. Note: Resetting the thermostat switches
the option to ELE.
4
to advance to the next menu item or
CONFIGURATION MENU
Displayed Press
Press (Factory to select from
Button Default) listed options
MS 2 HP 1, HP 2, SS 1
(GAS)
Days (7)
PS (4)
Cool Off Cool Off Heat (Emer), Selects system switch configuration for Heat and Cool with
Heat Auto Off Heat, Cool Off
E (On)
Cr Heat (FA)
Cr Cool (FA)
Cr Emer (FA)
CL (OFF)
dL (On)
0 1, 2, 3, 4 HI
(Room temp) 1, 2, 3, 4 LO
°F
b (On)
Heat (99) 62-99
Cool (45) 45-82
Keypad
lockout (L) Temperature Limit
Keypad
lockout (OFF)
000 000 to 999
FA Heat (On)
FA Cool (On)
000 Change
Filter (OFF)
200 hours 25 to 1975 hours
Change
Humidifier
(OFF)
100 hours 25 to 1975 hours
to return to a previous menu item. Press
or
Comments
Selects Multi-Stage (MS 2, No Heat Pump), Heat Pump 1
(HP 1, 1 compressor), Heat Pump 2 (HP 2, 2 compressor
or 2 speed compressor), or Single Stage.
ELE GAS setting: furnace controls blower.
ELE setting: thermostat controls blower.
5, 0 Selects programming option.
2 Selects programming steps per day.
Auto changeover, Heat & Cool, Heat Only or Cool Only.
OFF Selects Energy Management Recovery on or off.
SL Selects Heat cycle rate Fast (FA) or Slow (SL).
SL Selects Cool cycle rate Fast (FA) or Slow (SL).
SL If HP 1 or HP 2 is selected for item #1, selects Emer cycle
rate.
On Selects Compressor lockout ON or OFF.
OFF Selects display light on or off.
Selects temperature display adjustment 1, 2, 3 or 4 degrees
high or low.
°C Selects Fahrenheit or Celsius temperature display.
OFF Selects beeper on or off.
Selects highest Heat setpoint temperature.
Can select 62° to 99°F .
Selects lowest Cool setpoint temperature.
Can select 45° to 82°F .
L, P Selects keypad lockout full or partial to be set.
Activates temperature limit ranges.
On Selects keypad lockout on or off.
Selects keypad lockout combination number if lockout is on.
000 is not a valid selection.
OFF If HP or MS selected in item 1, selects Heat Fast second
stage On or Off.
OFF If HP or MS selected in item 1, selects Cool Fast second
stage On or Off.
On Select change filter alert time period.
When set ON, selects time in 25 hour increments.
On Selects change humidifier pad alert time period
When set ON, selects time in 25 hour increments.
3) This control can be configured for 7 independent day or
5/1/1 day programming or non-programmable mode. The
display indicates "7 Days" as default. The programs per
week can be toggled to "5 Days" or "0 Days" by pressing
the or keys. A selection of 0 Days for non-program-
mable will eliminate the need for EMR, and that step
in the menu will be skipped.
4) Programmable Periods – This control can be configured
for 4 or 2 programmable periods per day. The display
indicates "4 PS" in the display as default. The program-
mable periods can be toggled by pressing the
keys.
or
or