Contents Introduction Introduction Suitable for Caspian (UVC) Declaration of conformity These heaters must not be installed in wet rooms Symbols used in this guide or other high humidity areas. Important safety and installation instructions These heaters are designed for use on standard Product information two-pipe pumped central heating systems with a maximum water temperature of 86°C and a...
Declaration of conformity Symbols EC Declaration of conformity This manual contains information and prescriptions marked by the following symbols. We, Smith’s Environmental Products Limited 1-2 Blackall Industrial Estate South Woodham Ferrers Ignoring these safety provisions Chelmsford marked by the symbol “caution: Essex CM3 5UW hazard”...
Important safety and installation instructions Prior to installation, read these installation and operating instructions. The installation and operation should also be in accordance with national regulations and accepted codes of good practice. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
7. Electric connection IMPORTANT: Connection to the power supply must be effected by means of a fixed power cable which is fitted with a plug-type connection or a two pole isolating switch with a minimum contact opening of 3 mm. Electrical connection must be carried out by a qualified electrician and in accordance with local regulations and both data on the name-plate and the appropriate diagram inside the terminal box cover.
Control mounting options/configurations Wall mounted remote Smart Control Wall mounted thermostat position - 1.5m from floor Issue 001 - October 2023 | SmithsEP.co.uk | 9...
Mounting Options Bottom Back Exploded diagram with base unit shown in centre laying on its back, all other parts available separately Fix the unit to the ceiling or wall via suitable Optional extras and accessories fixings. If fitted to suspended ceilings or similar Air Inlet: air inlet should be through one of 3 then suitable means of support such as threaded options (front, bottom, back inlet) shown in blue...
Page 11
Inlet / Outlet Ducting & Grilles Straight 1 Metre Duct STR1MDCT (Marked as “A” in exploded diagram, See page 10) A Straight 1 Metre duct for either inlet/ outlet of the product. May be cut to size if necessary. Available sizes (90/120/150 &180) 90 Degree Duct 90DEGDCT (Marked as “B”...
Wiring diagrams Caspian UVC fitted with Remote Smart Contol Valve Acutator 230 / 10V INTERFACE 24VAC SLAVE SUPPLY OUTPUT OUTPUT Note: If your heater was built before October 2014 or the colours shown in this diagram do not match those on your unit please refer to the below Key: +10V (Red) Blue...
Installation Note: We recommend the use of full-flow service valves. The valves should be accessible after completion of the installation. We also advise the 1. Unscrew electrical panel fitting of an air vent at the highest point on either the flow or return pipe to remove any air trapped Unscrew electrical panel to and any packing pieces within the system.
Installation - Remote smart controller 1. Ensure power supply is switched off 2. Remove the mounting plate from the controller by inserting a small screwdriver into slots at base of controller. See Fig 2. Fig. 5 Fig. 6 3. Fix the mounting plate to the wall using either a recessed or surface mounted back box using Connecting remote smart the screws provided.
Commissioning Quick user guide for Wi-Fi Thermostat 1. Turn on the electrical supply at the fused spur. 2. Set the thermostat to maximum using the increase button on the controller. 3. Turn on the central heating system. 4. Balance the central heating system to ensure the correct system flow rate is achieved.
LCD Icon descriptions Getting started All units are factory configured in off-line stand alone mode and tested for function when built. Should your unit require setup from storage or reconfiguration to “Smart Home” App control follow the steps below to ensure successful setup and operation.
Page 17
1. When powered for the first time the control 5. Select the thermostat mode, although this unit is heating only by setting heating and cooling will boot (Software version will appear) after a allows the use of fan only/ventilation sort time the display will change to show if required.
Page 18
Changing from offline Scan for equipment Press from the App and mode to online mode follow the on screen instructions. If you want to use the internet App and the Universal Gateway Hub UG600 (available as an accessory product code: HACA33130), you need to change your thermostat settings from offline mode to online mode.
Page 19
Factory reset User Guide If you have made an error or need to change For further information and to view detail of set your system parameters, or want to return to up, operation and parameters, please consult the the factory settings, please follow steps below. full manual at: By performing this action you will lose all your https://salus-controls.com/uk/product/fc600/#downloads...
Maintenance Warning! Isolate from the electrical supply The coil fins are delicate so take care and only use before performing any work on the unit. a soft brush or vacuum cleaner to remove any dust that may have accumulated. The internal air filter is removable for servicing. To gain access to the filter unlock and lower the front access panel, remove the 2 screws from the filter enclosure panel and lift out.
Spares See the table below to find the product code for any spares that maybe required for your Caspian product. Model Component UVC Filter x 1 03-6015 03-6016 03-6017 03-6041 03-6043 06-0321 x 1 06-0321 x 2 06-0321 x 2 06-0321 x 3 06-0321 x 4 Coil...
Surface mounting Suspended mounting 1. Fit feet (supplied) to the unit at the 1. Decide on elevation of heater and note which appropriate height and position and drill part of the heater will be facing upwards. suitable size holes through the plastic base of 2.
Registering your product Disposal As part of the policy of continuous product Thank you for purchasing a Smith’s product. It has improvement, Smith’s Environmental Products LTD been designed and manufactured to the highest reserves the right to alter specification without quality standards to ensure it gives you efficient prior notice.
Page 24
Happy to help To view the full product information download the datasheet at: Smith’s Environmental Products Ltd is one of the leading manufacturers of heating and cooling www.SmithsEP.co.uk products in the UK. We are committed to achieving the highest standards and our faith is For product information, customer services or supported by a free parts and labour guarantee sales support call us on +44 (0) 1245 324900...