Advertisement

SERVICE MANUAL
Ver 1.2 2002. 03
US and foreign patents licensed from Dolby
Laboratories Licensing Corporation.
CD player section
System
Laser
Frequency response
Signal-to-noise ratio
Wow and flutter
HDD section
Capacity
Recording system
Transfer rate
Maximum recording time About 600 h
Maximum number of albums
Maximum number of tracks
Maximum number of tracks per album
Maximum CD-HDD ripping speed
Input
ANALOG
IN
DIGITAL
OPTICAL
IN
Sony Corporation
9-873-306-03
2002C1600-1
Home Audio Company
© 2002.03
Published by Sony Engineering Corporation
SPECIFICATIONS
Compact disc and digital
audio system
Semiconductor laser
(λ = 780 nm)
Emission duration:
continuous
5 Hz – 20 kHz (±0.5 dB)
More than 95 dB
Below measurable limit
40 GB
ATRAC 3
132 kbps
500
20,000
400
Max. ×2
Jack
Input
Rated
Minimum
type
impedance
input
input
Phono
47 kilohms
500 mVrms
125 mVrms
jacks
Square
Optical
optical
wave length:
connector
660 nm
jack
HAR-D1000
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Base Unit Name
Optical Pick-up Name
Output
Jack type
Rated
output
ANALOG
Phono
2 Vrms (at
OUT
jacks
50 kilohms)
General
Power requirements
US and Canadian model : 120 V AC, 60 Hz
European model
: 230 V AC, 50/60 Hz
Power consumption
25 W
Dimensions (Approx.) (w/h/d)
Mass (Approx.)
3.9 kg
Supplied accessories
Audio connecting cord (2)
Remote commander (remote) (1)
Sony R6 (size AA) battery (2)
USB cable (1)
"M-crew for HAR-D1000" CD-ROM(1)
"M-crew for HAR-D1000" operating instructions(1)
Design and specifications are subject to change
without notice.
HARD DISC AUDIO RECORDER
US Model
Canadian Model
AEP Model
MXD-D4
CDM55B-21BD53
BU-21BD53
OP Assy (A-MAX.2)
Load
impedance
Over
10 kilohms
430 × 82.5 × 285 mm
incl. projecting parts and
controls

Advertisement

Table of Contents
loading

Summary of Contents for Sony HAR-D1000

  • Page 1 20,000 Maximum number of tracks per album Audio connecting cord (2) Remote commander (remote) (1) Maximum CD-HDD ripping speed Sony R6 (size AA) battery (2) Max. ×2 USB cable (1) “M-crew for HAR-D1000” CD-ROM(1) Input “M-crew for HAR-D1000” operating instructions(1)
  • Page 2 DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT voltmeter (0.75 V) CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY. Earth Ground Fig.
  • Page 3: Table Of Contents

    HAR-D1000 TABLE OF CONTENTS 1. SERVICING NOTES 7. EXPLODED VIEWS ······················································· 4 7-1. Case Section ································································ 54 2. GENERAL 7-2. Flont Panel Section ······················································ 55 ·········································································· 7 7-3. Chassis Section ···························································· 56 7-4. CD Mechanism Deck Section ····································· 57 3. DISASSEMBLY 3-1.
  • Page 4: Servicing Notes

    HAR-D1000 SECTION 1 Ver 1.1 2001.12 SERVICING NOTES CLEANING OBJECTIVE LENS OF OPTICAL PICK-UP NOTES ON HANDLING THE OPTICAL PICK-UP • In cleaning the objective lens of optical pick-up, be sure the BLOCK OR BASE UNIT following below. The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the In cleaning the lens, do not apply an excessive force.
  • Page 5 HAR-D1000 CD SECTION • In checking the CD block and MAIN board, prepare jig. • In checking the CD block, prepare jig (extension cable J-2501-075-A) to connect the BD (CD) board (CN101) and MAIN board (CN302). • In checking the MAIN board, prepare jig (extension cable J-2501-094-A) to connect the MAIN board (CN305) and DISPLAY board (CN951).
  • Page 6 HAR-D1000 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is not a fault) TRACK Recorded contents Display ! ” # $ % & ´ (21h to 27h)1kHz 0dB L&R...
  • Page 7: General

    HAR-D1000 SECTION 2 This section is extracted GENERAL from instruction manual. Front Panel Remote Control 3 456 9q;qaqs qd qfqg 1 / u SELECT INFO PLAY MODE REPEAT OPEN/ CDSYNC INPUT CLOSE DISPLAY SCROLL TIME MENU/NO ALBUM STANDBY NAME EDIT...
  • Page 8: Loading Panel

    HAR-D1000 SECTION 3 DISASSEMBLY Note : Disassemble the unit in the order as shown below. Case Front panel section Sub board, Main board Loading panel Power board Case Hard disk CD mechanism deck Holder (BU) assy OP base unit (BU-21BD), Holder (55-BU21)
  • Page 9: Case

    HAR-D1000 3-2. CASE 1 Two screws (CASE3 TP2) 2 Two screws (CASE3 TP2) 4 CASE 3 Two screws (CASE3 TP2) 3-3. FRONT PANEL ASSY 1 Wire (flat type) (18 core) (CN305) 4 Two claws 2 Ground 5 Front panel assy 3 Four screws (BVTP 3 ×...
  • Page 10: Sub Board, Main Board

    HAR-D1000 3-4. SUB BOARD, MAIN BOARD 2 Connecter 1 Two screws (BVTP 3 × 8) (CN901) 3 SUB board 4 Five screws (BVTP 3 × 8) 3 Connecter 7 MAIN board (CN101) 5 Screw (BVTP 3 × 8) 6 Three screws (BVTP 3 ×...
  • Page 11: Hard Disk

    HAR-D1000 3-6. HARD DISK 4 Four screws (BVTT 3 × 10) 3 Screw (BVTP 3 × 8) 2 Two screws (BVTP 3 × 8) 8 Bracket (HDD) 7 Two screws (3 × 4.5) 6 Two screws (3 × 4.5) 1 Connector...
  • Page 12: Holder (Bu) Assy

    HAR-D1000 3-8. HOLDER (BU) ASSY 2 Floating screw (PTPWH M2.6) 4 Holder (BU) assy 1 Rotate the lever (SW) in the direction of the arrow A. 3-9. OP BASE UNIT (BU-21BD), HOLDER (55-BU21) 1 Three floating screws (DIA. 12) 7 Base unit...
  • Page 13: Loading Board

    HAR-D1000 3-10. LOADING BOARD 2 Belt (CDM55) Two claws 1 Rotate the gear (B) in the direction of arrow A. 3 Pull the tray pushing two claws. 5 Loading board 4 Two screws (BTP 2.6 × 8) 3-11. CAM (CDM55)
  • Page 14: Test Mode

    HAR-D1000 SECTION 4 Ver 1.1 2001.12 TEST MODE This set provides various modes for the service. Enter the test mode through the procedure given below, and select the desired mode. Procedure: [YES] 1. Press the (CD), (HDD) and buttons at the same time.
  • Page 15 HAR-D1000 Ver 1.1 2001.12 Microcomputer Version Display Procedure: [ALBUM] [ALBUM] Enter the test mode, then turn the dial to display “<Version> 1”, and press the dial. [ALBUM] The [MC] version is displayed, and then rotate the dial. [ALBUM] The message <TA> version is displayed. Rotate the dial again and <CD>, <CDM>, <DISP>...
  • Page 16 HAR-D1000 Ver 1.1 2001.12 CD SECTION Set the CD test mode when performing confirmations (refer to page 5). After completing confirmation, release the CD test mode. 1. C1, C2 ERROR DISPLAY Procedure: [ALBUM] [ALBUM] (1) Enter the CD test mode, then rotate the dial to display “1>...
  • Page 17 HAR-D1000 Ver 1.1 2001.12 HDD SECTION Set the HD test mode when performing confirmation (refer to page 11). After completing confirmation, release the HD test mode. Note : If any of the following test modes is executed, data is written in the HD.
  • Page 18 HAR-D1000 Ver 1.1 2001.12 3. READ TEST * This mode needs not be performed in normal operation. * Perform this mode only for the newly formatted HD. Procedure: [ALBUM] [ALBUM] (1) Enter the HD test mode, then rotate the dial to display “Read Test?”, and press the dial to display “IN”.
  • Page 19: Cd Section

    HAR-D1000 SECTION 5 Ver 1.1 2001.12 ELECTRICAL ADJUSTMENTS Note: A clear RF signal waveform means that the shape “◊” can be clearly CD SECTION distinguished at the center of the waveform. Note: RF signal waveform CD Block is basically designed to operate without adjustment.
  • Page 20 HAR-D1000 Checking Location: – BD BOARD (Side B) – (VC) IC171 (FE) TP (TE) TP (RFDC) IC101...
  • Page 21: Diagrams

    HAR-D1000 SECTION 6 Ver 1.1 2001.12 DIAGRAMS 6-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) Note on Printed Wiring Board: Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. p : pF •...
  • Page 22 HAR-D1000 • Waveforms – BD Board – – MAIN Board – – SUB Board – IC101 wg IC2 qd (XOUT) IC101 <zbb> (XTAL) (MDP) (CD PLAY mode) 2.6 Vp-p 3.2 Vp-p 3.2 Vp-p 100 ns 7.9 µ s 200 ns IC101 el IC4 e;...
  • Page 23: Block Diagram - Hdd/Sub Section

    HAR-D1000 Ver 1.1 2001.12 6-2. BLOCK DIAGRAM – HDD/SUB SECTION – (Page 24) (Page 24) (Page 24) (Page 24) (Page 24) (Page 24) (Page 24) •SIGNAL PATH : CD PLAY : HDD PLLAY : HDD REC (Page 24)
  • Page 24: Block Diagram - Main Section

    HAR-D1000 Ver 1.1 2001.12 6-3. BLOCK DIAGRAM – MAIN SECTION – IC303 DIGITAL WAVE OPTICAL SHAPER OPTICAL RECEIVER IC302 J300 ADDT DATA0 VINL LINE LRCK DIGITAL DECIMATION CONVERTER (Page 23) CANCELLATION INTERFACE FILTER BLOCK FILTER IC305 VINR +3.3V RESET PWON...
  • Page 25: Block Diagram - Display/Power Supply Section

    HAR-D1000 6-4. BLOCK DIAGRAM – DISPLAY/POWER SUPPLY SECTION – FL LED DRIVER IC751 REMOTE CONTROL S01–S35 RECEIVER SIRCS S731-733,S735,736 IC781 KEY2 FLUORESCENT G02–G23 FLCLK INDICATOR TUBE FLWITE FL751 S741-745 FL DROVE COM01 Q754 KEY3 FL DROVE COM24 Q753 FLCS S722,723,725,726...
  • Page 26: Schematic Diagram - Bd Section

    HAR-D1000 6-5. SCHEMATIC DIAGRAM – BD SECTION – • See page 22 for Wavefoms. (Page29) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Note on Schematic Diagram: Replace only with part number specified.
  • Page 27: Printed Wiring Board - Bd Section

    HAR-D1000 6-6. PRINTED WIRING BOARD – BD SECTION – • See page 21 for Circuit Boards Location. BD BOARD (SIDE A) BD BOARD (SIDE B) (SPINDLE) S101 (LIMIT) (VC) (FE) (TE) (RFDC) MAIN BOARD (SIDE A) CN302 (Page 32) C1 C2...
  • Page 28: Schematic Diagram - Main (1/4) Section

    HAR-D1000 Ver 1.2 2002.03 6-7. SCHEMATIC DIAGRAM – MAIN (1/4) SECTION – • See page 22 for Wavefoms. • See page 44 for IC Pin Function Descriptions.
  • Page 29: Schematic Diagram - Main (2/4) Section

    HAR-D1000 Ver 1.1 2001.12 6-8. SCHEMATIC DIAGRAM – MAIN (2/4) SECTION – • See page 22 for Wavefoms. • See page 42, 43 for IC Block Diagrams. • See page 46 for IC Pin Function Descriptions. IC B/D IC B/D...
  • Page 30: Schematic Diagram - Main (3/4) Section

    HAR-D1000 Ver 1.2 2002.03 6-9. SCHEMATIC DIAGRAM – MAIN (3/4) SECTION – • See page 43 for IC Block Diagrams. IC B/D IC B/D...
  • Page 31: Schematic Diagram - Main (4/4) Section

    HAR-D1000 Ver 1.2 2002.03 6-10. SCHEMATIC DIAGRAM – MAIN (4/4) SECTION –...
  • Page 32: Printed Wiring Board - Main (Side A) Section

    HAR-D1000 Ver 1.2 2002.03 6-11. PRINTED WIRING BOARD – MAIN (SIDE A) SECTION – • See page 21 for Circuit Boards Location. NOT USED (Page 35) IC 3805 IC 700 IC 3 IC 4 IC 508 IC 11 IC 800...
  • Page 33: Printed Wiring Board - Main (Side B) Section

    HAR-D1000 Ver 1.2 2002.03 6-12. PRINTED WIRING BOARD – MAIN (SIDE B) SECTION – • See page 21 for Circuit Boards Location. IC 303 IC 504 IC 100 IC 3504 IC 305 USED IC 2 IC 3112 IC 300 (SIDE B)
  • Page 34: Schematic Diagram - Panel Section

    HAR-D1000 6-13. SCHEMATIC DIAGRAM – PANEL SECTION – • See page 22 for Wavefoms.
  • Page 35: Printed Wiring Board - Panel Section

    HAR-D1000 6-14. PRINTED WIRING BOARD – PANEL SECTION – • See page 21 for Circuit Boards Location. IC 751 IC 781 (SIDE A) (Page 32) • Semiconductor Location Ref. No. Location D751 D806 D807 D808 D809 D810 IC751 B-11 IC781...
  • Page 36: Schematic Diagram - Sub (1/2) Section

    HAR-D1000 Ver 1.2 2002.03 6-15. SCHEMATIC DIAGRAM – SUB (1/2) SECTION – • See page 22 for Wavefoms. • See page 49 for IC Pin Function Descriptions. * Replacement of IC101 used in this set requires a special tool.
  • Page 37: Schematic Diagram - Sub (2/2) Section

    HAR-D1000 Ver 1.2 2002.03 6-16. SCHEMATIC DIAGRAM – SUB (2/2) SECTION – • See page 52 for IC Pin Function Descriptions. * Replacement of IC401 used in this set requires a special tool.
  • Page 38: Printed Wiring Board - Sub (Side A) Section

    HAR-D1000 Ver 1.2 2002.03 6-17. PRINTED WIRING BOARD – SUB (SIDE A) SECTION – • See page 21 for Circuit Boards Location. NOT USED IC 102 IC 103 • Semiconductor Location Ref. No. Location D191 D192 D193 IC102 IC103 Q191...
  • Page 39: Printed Wiring Board - Sub (Side B) Section

    HAR-D1000 6-18. PRINTED WIRING BOARD – SUB (SIDE B) SECTION – • See page 21 for Circuit Boards Location. NOT USED ∗ IC 401 (SIDE A) ∗ IC 402 IC 101 (Page 32) IC 701 • Semiconductor IC 702 Location Ref.
  • Page 40: Schematic Diagram - Power Section

    HAR-D1000 Ver 1.2 2002.03 6-19. SCHEMATIC DIAGRAM – POWER SECTION – US,CANADIAN C3106 220/200V 220/400V C3130 0.01/125V 0.002/250V F3101 2A/125V 2A/250V R3901 220K 470K R3902 220K 470K R3903 220K 470K...
  • Page 41: Printed Wiring Board - Power Section

    HAR-D1000 6-20. PRINTED WIRING BOARD – POWER SECTION – • See page 21 for Circuit Boards Location. (SIDE B) (Page 33) IC 3102 IC 3101 • Semiconductor Location Ref. No. Location D3101 D3102 D3103 D3104 D3105 D3106 D3107 D3108 D3109...
  • Page 42: Ic Block Diagrams

    HAR-D1000 6-21. IC BLOCK DIAGRAMS TUSB2046BVF (MAIN BOARD) M66290AFP (MAIN BOARD) TRNSCEIVER CLOCK CONTROL SUSPEND/RESUME (OSC/PLL) LOGIC AND OSC/PLL HUB REPEATER FRAME TIMER DEVICE VBUS CONTROL PERIPHERALS UNIT SERIAL REGISTER TRON SERIAL INTERFACE EEPROM OVRCUR4 ENGINE SIE INTERFACE INTERFACE LOGIC...
  • Page 43 HAR-D1000 IC401 M54641L (MAIN BOARD) OUT2 INPUT AMP. POWER AMP. CONTROL INPUT OUT1 AMP. POWER AMP. REFERENCE µDA1350AH (MAIN BOARD) IC300 41 40 39 38 37 36 RESET BCKO VDDD (C) VDDA (PLL) VSSD 31 VSSA (PLL) VSSD (C) PREEM1...
  • Page 44: Ic Pin Function Descriptions

    HAR-D1000 6-22. IC PIN FUNCTION DESCRIPTIONS • IC700 M30624FGAFP-B55F (UART TO IIC CONVERT) (MAIN BOARD) Pin No. Pin Name Description O_CD-DATA — Not used O_CD-CLK — Not used O_XLT — Not used I_SIRCS — Not used A1IN Input terminal of Control A1 I_SQ-DATA —...
  • Page 45 I_KEY0 — Not used I_SPEC_IN — Not used I_LEVEL_L — Not used I_LEVEL_R Input terminal for identification of model (HAR-D1000:Low) AVss — Ground (Analog) (I_TE) Input terminal for identification of destination (U model:Low) Vref — A/D reference voltage AVcc —...
  • Page 46 HAR-D1000 • IC800 M30624FGAFP-A08F (SYSTEM CONTROLLER (CD MECHANISM CONTROLLER)) (MAIN BOARD) Pin No. Pin Name Description CD-DATA Serial data output to the CD block CD-CLK Serial data transfer clock signal output to the CD block Serial data latch pulse signal output to the CD block...
  • Page 47 HAR-D1000 Pin No. Pin Name Description LED_CLK LED control serial data transfer clock signal output terminal Not used (open) LED_STB LED control strobe signal output terminal Not used (open) 56 to 58 Not used (open) HD_P_DOWN Power down signal to the HDD coltrol...
  • Page 48 HAR-D1000 Pin No. Pin Name Description KEY1 Key input terminal (A/D input) S722, S723, S725, S726 (CLEAR, SEARCH, INPUT, DISPLAY keys input) KEY0 Key input terminal (A/D input) S702 to S704, S706 to S708 ( x (CD), X (CD), H (CD), L (CD),...
  • Page 49 HAR-D1000 • IC101 HD6417709ABT100B (SYSTEM CONTROL) (SUB BOARD) Pin No. Pin Name Description MD 1, 2 Clock mode setup input Vcc-RTC — Power supply terminal for RTC XTAL2 RTC crystal oscillator terminal EXTAL2 RTC crystal oscillator terminal Vss-RTC — Ground terminal for RTC...
  • Page 50 HAR-D1000 Pin No. Pin Name Description Address bus (not used) VccQ — Power supply terminal for IO Address bus (not used) PTK4 (Not used) Read signal output for IC401(CXD1859) and IC102(FLASH ROM) Lower data write signal output for IC401(CXD1859) and IC103(SDRAM)
  • Page 51 HAR-D1000 Pin No. Pin Name Description Vcc-PLL1 — Power supply terminal for PLL1 CAP1 — External capacity terminal for PLL1 147,148 Vss-PLL1,2 — Ground terminal for PLL1,2 CAP2 — External capacity terminal for PLL2 VccPLL2 — Power supply terminal for PLL2...
  • Page 52 HAR-D1000 • IC401 CXD1859AGA (DIGITAL SIGNAL PROCESSOR, ATRAC ENCODER/DECODER) (SUB BOARD) Pin No. Pin Name Description CLKSEL2 Clock mode selection input XTAL0 Oscillator output (Not used) EXTAL0 Oscillator input VSC0 — Ground 5 to 6 CLKSEL3 - 4 Clock mode selection input VDC0 —...
  • Page 53 HAR-D1000 Pin No. Pin Name Description VSC8 — Ground 73 to 77 ADR10 - 14 Address bus (Host bus interface) Read enable signal input VSC9 — Ground XWRU Upper byte write enable signal input XWRL Lower byte write enable signal input...
  • Page 54: Case Section

    HAR-D1000 SECTION 5 Ver 1.2 2002.03 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0 or have some differences from the original one.
  • Page 55: Flont Panel Section

    HAR-D1000 Ver 1.2 2002.03 7-2. FLONT PANEL SECTION supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-236-510-01 KNOB (GROUP)(US, CND) 4-236-504-11 BUTTON (CDP)(AEP) 4-236-510-11 KNOB (GROUP)(AEP) 4-236-505-01 BUTTON (HDD)(US, CND) 4-236-496-01 PLATE, INDICATION(US, CND) 4-236-505-11 BUTTON (HDD)(AEP)
  • Page 56: Chassis Section

    HAR-D1000 Ver 1.2 2002.03 7-3. CHASSIS SECTION supplied supplied supplied supplied supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-4726-930-A MAIN MOUNTED BOARD (US, CND) 4-236-498-11 PANEL, BACK(AEP) A-4727-686-A MAIN MOUNTED BOARD (AEP) X-4953-448-1 FOOT ASSY 1-920-775-21 WIRE IDE 40 PIN 4-232-237-01 FOOT (DIA.
  • Page 57: Cd Mechanism Deck Section

    HAR-D1000 Ver 1.2 2002.03 7-4. CD MECHANISM DECK SECTION M702 not supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 4-226-180-01 TRAY (55-L) X-4953-843-1 PULLEY (4TCD) ASSY 4-229-358-01 SHAFT (BU21) 4-220-951-02 SHEET (KH) 1-674-336-21 LOADING BOARD 4-227-899-21 SCREW (DIA.
  • Page 58: Electrical Parts List

    HAR-D1000 SECTION 8 Ver 1.2 2002.03 ELECTRICAL PARTS LIST LOADING MAIN NOTE: • Due to standardization, replacements in the • RESISTORS • SEMICONDUCTORS parts list may be different from the parts All resistors are in ohms. In each case, u: µ, for example:...
  • Page 59 HAR-D1000 Ver 1.2 2002.03 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C337 1-162-915-11 CERAMIC CHIP 10PF C620 1-162-923-11 CERAMIC CHIP 47PF C338 1-216-864-11 METAL CHIP 1/16W C621 1-162-923-11 CERAMIC CHIP 47PF C339 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 60 HAR-D1000 Ver 1.2 2002.03 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C1826 1-162-923-11 CERAMIC CHIP 47PF IC13 8-759-096-87 IC TC7WU04FU(TE12R) C1827 1-162-923-11 CERAMIC CHIP 47PF IC100 8-759-100-96 IC NJM4558M-TE2 C1830 1-164-315-11 CERAMIC CHIP 470PF 5.00% 50V...
  • Page 61 HAR-D1000 Ver 1.2 2002.03 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < TRANSISTOR > R102 1-216-821-11 METAL CHIP 1/16W R103 1-218-694-11 METAL CHIP 1.2K 0.5% 1/16W 8-729-120-28 TRANSISTOR 2SC3052F-T2-LF R104 1-216-823-11 METAL CHIP 1.5K...
  • Page 62 HAR-D1000 Ver 1.2 2002.03 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R350 1-216-833-11 METAL CHIP 1/16W R823 1-216-809-11 METAL CHIP 1/16W R400 1-216-296-11 SHORT R824 1-216-809-11 METAL CHIP 1/16W R402 1-216-864-11 METAL CHIP 1/16W...
  • Page 63 HAR-D1000 Ver 1.2 2002.03 MAIN PANEL Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks RB806 1-236-908-11 NETWORK RESISTOR (CHIP) 10K < FILTER > RB810 1-233-414-11 RES, CHIP NETWORK 4.7K (3216) FL751 1-518-779-11 INDICATOR TUBE, FLUORESCENT < VIBRATOR >...
  • Page 64 HAR-D1000 Ver 1.2 2002.03 PANEL POWER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < SWITCH > C3126 1-126-936-11 ELECT 3300uF 20.00% 16V 0 C3130 1-113-927-11 CERAMIC 0.01uF 99.00% 125V S702 1-762-875-21 SWITCH, KEYBOARD(x CD) (US, CND)
  • Page 65 HAR-D1000 Ver 1.2 2002.03 POWER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < RESISTOR > C118 1-162-969-11 CERAMIC CHIP 0.0068uF 10% C119 1-164-156-11 CERAMIC CHIP 0.1uF 0 R3101 1-215-902-11 METAL OXIDE C120 1-164-156-11 CERAMIC CHIP 0.1uF...
  • Page 66 HAR-D1000 Ver 1.2 2002.03 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < CONNECTOR > R156 1-216-845-11 METAL CHIP 100K 1/16W R157 1-216-845-11 METAL CHIP 100K 1/16W CN461 1-784-861-21 CONNECTOR, FFC(LIF(NON-ZIF))9P R158 1-216-845-11 METAL CHIP 100K...
  • Page 67 HAR-D1000 Ver 1.2 2002.03 STAND-BY Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R918 1-216-789-11 METAL CHIP 1/16W MISCELLANEOUS R919 1-216-864-11 METAL CHIP 1/16W ************** R920 1-216-789-11 METAL CHIP 1/16W 1-569-972-21 SOCKET, SHORT 2P(AEP) R941 1-216-805-11 METAL CHIP...
  • Page 68 HAR-D1000 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.09...

Table of Contents