ResMed S9 Series User Manual
Positive airway pressure device
Hide thumbs
Also See for S9 Series:
- User manual (129 pages) ,
- Information manual (64 pages) ,
- Clinical manual (37 pages)
Table of Contents
Advertisement
1
2
B
C
Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA.
ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for other ResMed locations worldwide.
S9: Protected by one or more patents: AU 691200, AU 697652, AU 702820, AU 709279, AU 724589, AU 730844, AU 736723, AU 750095, AU 750761, AU 764761, AU 779327, AU 2007252223, CN
200780001837.6, EP 0651971, EP 0661071, EP 0920845, EP 0927538, EP 0934723, EP 1028769, EP 1126893, EP 1144036, EP 1502618, EP 2032857, JP 3580776, JP 3778797, JP 4647786, NZ 504595,
NZ 570415, NZ 573921, NZ 577485, US 5704345, US 6138675, US 6240921, US 6363933, US 6367474, US 6425395, US 6502572, US 6591834, US 6675797, US 6745768, US 6817361, US 6988498,
US 7040317, US 7100608, US 7537010, US 7866944. Other patents pending. Protected by design registrations: AU 329025, AU 330142, AU 331272, AU 332891, AU 333858, CN 200830346524.1, CN
200830346526.0, CN 200830346525.6, CN 201030215797.X, EU 1067417, JP 1377401, JP 1377402, JP 1377403, JP 1415251, JP 1415252, NZ 411762, NZ 413090, NZ 413091, US D629891, US
D629892, US D635232, US D635244, US D635245, US D635654, US D638536, US D638537, US D638933. Others pending. S9, S9 AutoSet, S9 Elite, ClimateLine, SlimLine and SmartStart are
trademarks of ResMed Ltd. S9, AutoSet, ClimateLine, SlimLine and SmartStart are registered in U.S. Patient and Trademark Office.
© 2011 ResMed Ltd. 368147/2 2011-08
Global leaders in sleep and respiratory medicine
3
4
5
6
www.resmed.com
S9
Series
™
AutoSet
& Elite
™
™
POSITIVE AIRWAY PRESSURE DEVICES
User Guide
English • Deutsch • Français • Italiano • Español • Português • Nederlands • Ελληνικά • Polski • Magyar • Pусский •
Türkçe • Česky • Slovensky
A
5
3
2
4
1
Advertisement
Table of Contents
Related Manuals for ResMed S9 Series
Summary of Contents for ResMed S9 Series
- Page 1 Türkçe • Česky • Slovensky Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA. ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for other ResMed locations worldwide.
-
Page 2: S9 Autoset Indications For Use
• skin rashes. Masks and humidifiers Recommended masks and humidifiers are available on www.resmed.com on the Products page under Service & Support. For information on using your mask or humidifier, refer to the manual supplied with your mask or humidifier. -
Page 3: Control Panel
Setup Refer to illustration A. 1. Connect the DC plug of the power supply unit to the rear of the S9. 2. Connect the power cord to the power supply unit. 3. Plug the other end of the power cord into the power outlet. 4. -
Page 4: Cleaning And Maintenance
1. Remove the air filter cover from the back of the S9 device. 2. Remove and discard the old air filter. 3. Insert a new ResMed air filter ensuring that it is sitting flat in the air filter cover. 4. Replace the air filter cover. - Page 5 SmartStart/Stop is enabled but the device does not stop automatically when you remove your mask Incompatible mask system being used. Only use equipment recommended by ResMed. The patient is using a nasal pillows Disable SmartStart/Stop. mask with a set pressure less than...
- Page 6 Turn the humidifier setting down and empty the water from in accumulation of water in the air the air tubing. tubing. Displays error message: Check ResMed 30/90W Power Supply Unit and fully insert the connector The DC plug is partially inserted into the Fully insert the DC plug.
-
Page 7: Technical Specifications
Problem/Possible cause Solution The following message is NOT displayed on the LCD after you try to update the settings using the SD card: Settings updated successfully, press any key The settings were not updated. Contact your clinician/service provider immediately. SD card An SD card has been supplied to gather therapy data from your S9 device and provide settings updates from your clinician. - Page 8 IEC60601-1-2, for residential, commercial, and light industry environments. Information regarding the electromagnetic emissions and immunity of these ResMed devices can be found on www.resmed.com, on the Products page under Service and Support. Click on the PDF file for your language.
- Page 9 If you need information on these disposal systems, please contact your local waste administration. The crossed-bin symbol invites you to use these disposal systems. If you require information on collection and disposal of your ResMed device please contact your ResMed office, local distributor or go to www.resmed.com/environment.
-
Page 10: Limited Warranty
• Portable diagnostic/screening devices This warranty is only available to the initial consumer. It is not transferable. If the product fails under conditions of normal use, ResMed will repair or replace, at its option, the defective product or any of its components. - Page 11 Do not use your S9 if there are obvious external defects or unexplained changes in performance. • Only ResMed air tubing and accessories should be used with these devices. A different type of air tubing or accessory may alter the pressure you actually receive, reducing the effectiveness of your...
- Page 12 A patient should not connect a device to the module connector port unless instructed to do so by their health care provider or physician. Only ResMed products are designed to be connected to the module connector port. Connecting other devices could result in injury, or damage to the S9 device.
- Page 13 CAUTIONS • Be careful not to place your device where it can be bumped or where someone is likely to trip over the power cord. • If you put the device on the floor, make sure the area is free from dust and clear of bedding, clothes or other objects that could block the air inlet or cover the power supply unit.