Extron electronics DXP 42 HD 4K PLUS Setup Manual page 9

Command Function
Information Requests (continued)
Query firmware version
Query firmware and build version
IP Setup
Set IP address
View IP address
Set subnet mask
View subnet mask
Set gateway IP address
View gateway IP address
Set DHCP on and off
View DHCP on/off status
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
Set verbose mode
Read verbose mode
KEY:
X#
= On or off (enable or disable)
X2%
= Firmware version number
X2^
= Firmware version and build number
X3)
= IP address
X3!
= Subnet mask
X3@
= Gateway IP address
X5#
= Verbose mode
X5*
= Port timeout interval
Reset
System reset to factory defaults
NOTE: This command excludes IP settings such as IP address and subnet mask. It does not remove the file system.
Absolute system reset
NOTES:
• This command includes resetting the IP address to 192.168.254.254 and the subnet mask to 255.255.0.0. The firmware
version remains the same.
• The factory configured passwords for all accounts on this device have been set to the device serial number. Passwords are
case sensitive. In the event of an absolute system reset, the passwords convert to the default, which is no password.
ASCII Command Response
(Host to Switcher) (Switcher to Host)
X2%]
Q
X2^]
*Q
E X3) }
CI Ipi
E } X3)]
CI
E X3! }
CS Ips
E } X3&]
CS
E X3@ }
CG Ipg
E } X3@]
CG
E X# }
DH Idh
E } X#]
DH
E X5* }
0* TC Pti0*
E } X5*]
0TC
E X5* }
1* TC Pti1*
E } X5*]
1TC
E X5# }
CV Vrb
E } X5#]
CV
0
= DHCP disabled (default), 1 = DHCP enabled
Expressed to the second decimal place (n.nn)
n.nn.nnnn
nnn.nnn.nnn.nnn (Default = 192.168.254.254)
nnn.nnn.nnn.nnn (Default = 255.255.0.0)
nnn.nnn.nnn.nnn (Default = 0.0.0.0)
0 = clear or none (default for Telnet connection)
1 = verbose mode (default for RS-232 and USB connection)
2 = tagged responses for queries
3 = verbose mode and tagged for queries
1 (10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)
E }
ZXXX Zpx
E }
ZQQQ Zpq
Additional Description
View the unit firmware version to the
second decimal place.
In verbose modes 2 and 3:
X2%
Ver01*
View unit firmware version and build
number
In verbose modes 2 and 3:
X2^
Bld01*
X3)]
Set the unit IP address to
View unit IP address.
X3!]
Set the subnet mask for the unit to
View the subnet mask.
X3@]
Set the unit gateway address to
View the unit gateway address.
X#]
Set DHCP to
View the DHCP setting.
X5*]
Set the current port timeout to
View the current port timeout setting.
X5*]
Set the global IP port timeout to
View the global IP port timeout setting.
Set the verbose mode and tagged
X5#]
responses to
View the current verbose mode.
] Clear all ties and presets and reset unit
to factory default settings.
] Clear all ties and reset unit to factory
default settings.
X2^
.
X3)
.
X3!
X3@
.
X#
.
X5*
.
X5*
.
X5#
.
.
9