Display Information, Options, Functions; Page 7, Programme Overview - Bosch WAS28461AU Instruction Manual

Hide thumbs Also See for WAS28461AU:
Table of Contents

Advertisement

Display information, Options, Functions

Display symbols
Display information
Before starting a programme, the max. load
for the selected programme is displayed
when the door is open. The remaining time
or finish-in time is displayed when the door
is closed.
*Display shown may vary depending on the
model and selected programme .
Option buttons
You can change the spin speed and temperature beforehand and while the selected programme is running. The effects
depend on the progress of the programme.
°C (Temp.)
You can change the indicated washing temperature. The maximum washing temperature that can be selected
depends on the programme that has been selected.
(Finish in)
When you select a programme, the respective programme duration is displayed. You can delay the start of the
programme before it begins. The finish-in time indicates when the programme will be finished. It can be set in hourly
increments up to a maximum of 24 hours. Press and hold the
is shown (h=hour). Select Start/Reload
(Spin speed)
You can change the indicated spin speed. The maximum spin speed which can be selected depends on the selected
programme. If
is selected, the load is held in the rinsing water.
Wash: On if wash process is running.
Rinse: On if rinse process is running.
Spin: On if spin process is active if the symbol
page 10
Water tap: Flashing if tap not open or no water supply.
Door: On if door can be opened.
Overdosage: On if too much detergent used.
Automatic load detection: Automatically detects the
load size after the water inlet phase and sets the accurate remaining
time. Symbols indicate small, medium and full loads measured*
according to the recommended max. load for the selected
programme.
* Automatic display of the detected load only for washing
programmes with a max. load recommendation > 3.0 kg except for
Rinse, Spin and Drain. Different types of textiles with different water
absorption rates may influence the load display.
kg, e.g.
kg*: max. recommended load for selected programme

page 7, Programme overview

time, e.g.
*: remaining time
*: finish-in time defined by user
: pause
: door can be opened in "Pause" status
: end of programme
: end of programme with the
setting
: set volume of signals
page 6
: Information on the display
page 10
(Finish-in) button until the required number of hours
.
Options, Functions
(Childproof lock)
To activate the childproof lock:
– After the programme starts, press and hold the
– Release when the
flashes
When the programme ends, the Start/Reload
deactivate the childproof lock.
*
symbol flashes if the programme has been changed while childproof lock is activated.
To deactivate the childproof lock:
– Touch and hold the
– Release the button.
If the childproof lock is deactivated while the programme selector is in a different position
from when the childproof lock was activated*, the current programme will be halted.
Additional functions
SpeedPerfect
EcoPerfect
Extra Rinse
Prewash
page 5
The additional function indicator light is on when this option is selected; if this option cannot
be selected for the programme, this is indicated by a short flashing of the light and an
acoustic signal.
Start/Reload
To start or pause the programme.
Signals
1. Start signal mode
2. Set volume for ...
*If required, set repeatedly
5
Programme cannot be changed by accidental operation.
button for 5 seconds;
symbol lights up.
indicator remains on to remind you to
button until the
symbol turns off;
See also Programme overview
For washing in a shorter time with a washing result
comparable to that of the standard programme.
For saving energy with a washing performance
comparable to that of the standard programme.
Additional rinse cycle. Prolonged programme duration.
For areas with very soft water or for further improving the
washing result.
Activate prewash. For heavily soiled, hard-wearing
textiles, e.g. made of cotton or linen.
Set to
1 step
Press and
clockwise
hold
Button signals
Information signals
direct
Set volume*
1 step
Set volume*
clockwise
page 7
1 step
Release
clockwise
Set to
6

Advertisement

Table of Contents
loading

Table of Contents