Table of Contents
Advertisement
Display information, Options, Functions
Display symbols
Display information
*Before starting a programme, the
max. load for the selected
programme is displayed when the
door is open. The remaining time or
finish-in time is displayed when the
door is closed.
Display shown may vary depending
on the model and selected
programme.
Option buttons
You can change the spin speed and temperature beforehand and while the selected
programme is running. The effects depending on the progress of the programme.
°C (Temp.)
You can change the indicated washing temperature. The maximum washing temperature
which can be selected depends on the programme that has been chosen.
(Finish in)
When you select a programme, the respective programme duration is displayed. You can
delay the start of the programme before it begins. The finish-in time indicates when the
programme will be finished. It can be set in hour increments up to a maximum of 24h. Press
and hold the
(Finish in) button until the required number of hours is shown (h=hour).
Downloaded From WashingMachine-Manual.com Manuals
Select Start/Pause
.
Washing:
Not on if Rinse, Spin or Drain is selected.
Rinse:
Not on if Spin or Pump is selected.
Spin:
Not on if a programme with the
final spin) is selected.
Water tap
Flashing
:
- tap not open or no water
supply.
on
– low water pressure.
Door:
On if door can be opened
.
Overdosage:
On if too much detergent used
Automatic load detection:
Automatically
detects the load size after water inlet phase and sets
accurate remaining time. Symbols indicate small, middle
and full loads measured* according to the recommended
max. load of the selected programme.
* Automatic display of the detected load only for washing
programmes with a max. load recommendation > 3.0 kg
except for Rinse, Spin and Drain. Different types of textiles
with different water absorption rates may influence the
load display.
kg, e.g.
kg : max. recommanded load for selected
programme
page 7, Programme overview
time, e.g.
: remaining time
: finish-in time defined by user
page 5
: pause
: door can be opened in Pause status
: end of programme
: end of programme with the
setting
set volume of signals
page 6
: error display
page 10
Options, Functions
(Spin speed)
You can change the indicated spin speed. The maximum spin speed which can be selected
depends on the chosen programme. If
(Childproof lock)
setting (no
To activate the childproof lock:
– After the programme starts, press and hold the
– Release when the
When the programme ends, the Start/Pause
deactivate the childproof lock.
*
symbol flashes if the programme has been changed while childproof lock is activated.
.
To deactivate the childproof lock:
– Touch the
– Release the button.
If the childproof lock is deactivated while the programme selector is in a different position
from when the childproof lock was activated*, the running programme will be halted.
Additional functions
Pre-wash
Water plus
Easy iron
Intensive
The additional function indicator light is on when the option is selected; if the option is not
selectable for the programme, this is indicated by a short flashing of the light and an
accoustic signal.
Start/Pause
For starting or pausing the programme.
Signals
1. Start signal
mode
2. Set volume for ...
*If required, set repeatedly
5
is selected, the load is held in the rinsing water.
Programme cannot be changed by accidental operation.
button for 5 seconds;
symbol lights up.
indicator remains on to remind you to
button until the
symbol turns off;
see also Programme overview
For heavily soiled, hard-wearing textiles. Pre-wash at
max. 30 °C.
High water level to achieve better rinse result.
Special spin sequence with subsequent fluffing. Gentle
final spin - residual moisture in the laundry increased
slightly.
Extends the washing time for a more intensive washing
of heavily soiled items.
Set to
1 step
Press
clockwise
hold
Button signals
direct
Set volume*
1 step
clockwise
page 7
1 step
Release
and
clockwise
Information signals
Set volume*
Set to
6
Advertisement
Table of Contents
