VTech USB 7100 User Manual page 16

Appendix
In case of difficulty
If you hear • You may be out of range. Move the handset closer to the base.
noise or
• Appliances plugged into the same circuit as the base can cause
interference
interference. Try moving the appliance or base to another outlet.
during a call
• The layout of your home or office might be limiting the operating
range. Try moving the base to another location, preferably on an
upper floor.
• If the buttons don't work, try placing the handset in the base for at
least 15 seconds.
• Disconnect the base from the modular jack and plug in a corded tele-
phone. If calls are still not clear, the problem is probably in your
wiring or local service. Call your local telephone service company.
Phone does • If only Internet calls do not ring, make sure your computer is on,
not ring connected to the Internet, and all required software is running.
• Make sure the ringer for the non-ringing line is on (see page 15).
• Make sure the telephone line cord and AC adapter are plugged in
properly (see page 5).
• Move the handset closer to the base.
• You might have too many extension phones on your telephone line to
allow all of them to ring. Try unplugging some of them.
Handset does • If the error message "Not Registered" is displayed, return the handset
not work to the base. If the error message remains after 60 seconds, you will
have to manually re-register the handset (see next page).
Intercom or call • Intercom and call transfer features cannot be used when both
transfer does Internet and standard telephone lines are in use. Try again when one
not work line is free.
Wrong date • The telephone's date and time are taken from your PC. Make sure
or time your PC is set to the correct time and date.
NOTE: The term "base" above refers to the telephone base, not the charger provided with expansion handsets.
28
Appendix
In case of difficulty
Manual handset If the error message "Not Registered" is displayed, return the handset to
registration the base. After 60 seconds the handset should beep to indicate that
registration is completed.
If registration fails, follow the steps below to deregister and reregister
your handset:
1 Select MENU.
V
2 Press until "Registration" is displayed, then select OK.
V
3 Press until "Deregister" is highlighted, then select OK.
V
4 Press until affected handset is highlighted, then select OK.
5 At the "Deregister?" confirmation prompt, select OK.
6 Press and hold the LOCATE HANDSET button on the base for at
least 5 seconds.
7 Select MENU.
V
8 Press until "Registration" is highlighted, then select OK.
9 Select OK to display "Search Base," then wait a few seconds. If reg-
istration is successful, you will be prompted to enter a handset name.
If the "Not Registered" message is still displayed, call VTech Customer
Support at the numbers listed on page 26.
If you have lost or broken a handset, you should de-register it from the
Lost or broken
base. Using a handset that is registered to the base, follow the steps
handsets
below to de-register the lost or broken handset:
1 Select MENU.
V
2 Press until "Registration" is displayed, then select OK.
V
3 Press until "Deregister" is highlighted, then select OK.
V
4 Press until affected handset is highlighted, then select OK.
5 At the "Deregister?" confirmation prompt, select OK.
Once that handset has been de-registered, you may attempt to register
the new handset.
Only one call will The USB7100 can only ring for one incoming call at a time (Skype, stan-
ring at a time dard, or intercom). If you receive a second call before answering the first
call, you will not be notified of the second call until after the first call is
answered. However, if you receive an incoming call while calling ALL
handsets (select * from the INTERCM menu), the incoming call will take
priority over the intercom call.
NOTE: The term "base" above refers to the telephone base, not the charger provided with expansion handsets.
29