Sony MHC-V3 Service Manual page 28

MHC-V3/V4D
Ver. 1.5
[MODEL & DEST WRITE MODE]
This mode is used to set software model & destination.
This mode is only available when no permanent model &
destination is stored.
Procedure:
1. Press [EQ] button and [OPTIONS]
ously and hold for 5 seconds.
2. Fluorescent indicator tube display will show "M XXXXX".
3. Press [+] / [‒] *1 or [+ PRESET +] / [‒ PRESET ‒]
button to select the model based on the set's model.
Product Code
SONY:MHC-V3
4. Press [ENTER] button.
5. Fluorescent indicator tube display will show "D XXXXX".
6. Press [+] / [‒] or [+ PRESET +] / [‒ PRESET ‒]
*1
button to select the destination based on the set's country.
Area Code Country
J1 Japan
JE1 Tourist
U2/CA2 America, Canada
CEL/CE1/ Europe (general)
CE2
CEK U.K.
RU1/RU3 Russia
AU1 Australia
CN1 China
E12 India, Pakistan, Morocco
E3/E15 Middle East, Iran
E4/EA3/ Saudi Arabia, Africa
E93/SA2
HK1/ Hong Kong, Philippines,
HK2/PL1/ Singapore, Malaysia,
SP1/SP2/ Thailand
SP6/TH1
KR2 Korea
TW2 Taiwan
E2, E32, Latin America (general),
E51, AR2 Chile, Peru, Argentina
BR1 Brazil
MX2, Mexico
MX4
7. Press [ENTER] button to confi rm the selection.
8. "RESET" appears on the fl uorescent indicator tube. After that,
the fl uorescent indicator tube becomes blank for a while, and
the system is reset.
9. Mode in [PANEL TEST MODE] again to confi rm on the
model & destination.
Note: *1 V3 model
*2 V4D model
28
*1 / [] *2 button simultane-
*2
F. Tube display
"M FSX0"
*2
F. Tube display
"D J"
"D JE"
"D NA"
"D CE2"
"D CEK"
"D RU"
"D AU"
"D CN"
"D E12"
"D E3"
"D EA3"
"D ASIA"
"D KR"
"D TW2"
"D LATIN"
"D BR"
"D MX"
[DVD COLOR SYSTEM MODE]
• This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
Procedure:
1. Press the [\/1] button to turn on the system.
2. Press the [FUNCTION] button until message "DVD/CD"
appears.
3. Press the [X] button and [‒ PRESET ‒] button
simultaneously and hold for 3 seconds.
4. The message "COLOR PAL" or "COLOR NTSC" appears on
the fl uorescent indicator tube.
• To release from DVD Color System Mode
1. Once the color system has been selected, the mode is fi xed
there after. If you wish to change the mode again, perform the
above item 2 again.
[DVD SERVICE MODE]
• This mode let you make diagnosis and adjustment easily by
using the remote commander and the TV. The instructions,
diagnostic results, etc. are given on the on-screen display.
• TEST DISC LIST
Be sure to use the DVD disc that matches the signal standards
of your region.
• CD
YEDS-18
PATD-012
• DVD SL (Single Layer)
NTSC : HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A)
PAL : HLX-506 (Part No.: J-6090-077-A)
• DVD DL (Double Layer)
NTSC : HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A)
PAL : HLX-507 (Part No.: J-6090-078-A)
• Procedure to enter to DVD Service Mode:
1. Press the [\/1] button to turn on the system.
2. Press the [FUNCTION] button until message "DVD/CD"
appears.
3. Press the [EQ] button and [ENTER] button simultaneously
and hold 3 seconds.
4. The message "SERVICE" appears on the fl uorescent indicator
tube.
The display of the "Model Name" of the "Remocon Diagnosis
Menu" change with the model and the destination appears on
screen display. Refer to below on the model name.
MHC-V4D: FSX0D
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. USB Test Mode Setting
Model Name : FSX0D_ XX
IF-con : Ver. XX.XX (XXXX)
Syscon : Ver. X.XXX
*1: Changes depending on destination
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press the [\/1] button to turn off
the system.
(Part No.: 3-702-101-01)
(Part No.: 4-225-203-01)
*1