Table of Contents

Advertisement

SERVICE MANUAL
Ver. 1.5 2015.06
Amplifi er section
The following are measured at
E51 models:
AC 220 V – 240 V, 50 Hz
Other models:
AC 120 V – 240 V, 50/60 Hz
Power output (rated)
Left/Right Channel: 120 W + 120 W
(at 2 ohms, 1 kHz, 1% THD)
RMS output power (reference)
Left/Right Channel: 180 W + 180 W
(per channel at 2 ohms, 1 kHz)
Subwoofer: 360 W (at 4 ohms, 100 Hz)
Inputs
AUDIO IN L/R
Voltage 2 V, impedance 47 kilohms
(USB) port
Type A
MIC 1 (V4D), MIC 2 (V4D)
Sensitivity 1 mV, impedance
10 kilohms
Outputs (V4D)
VIDEO OUT
Max. output level 1 Vp-p, unbalanced,
Sync. negative load impedance
75 ohms
USB section
Supported bit rate
WMA:
48 kbps – 192 kbps, VBR, CBR
AAC:
48 kbps – 320 kbps, VBR, CBR
Sampling frequencies
WMA: 44.1 kHz
AAC: 44.1 kHz
Supported USB device
Mass Storage Class
Maximum current
500 mA
Disc/USB section
Supported bit rate
MPEG1 Layer-3:
32 kbps – 320 kbps, VBR
MPEG2 Layer-3:
8 kbps – 160 kbps, VBR
MPEG1 Layer-2:
32 kbps – 384 kbps, VBR
9-890-660-06
Sony Corporation
2015F80-1
©
2015.06
Published by Sony EMCS (Malaysia) PG Tec
Photo: MHC-V3
CD/DVD Section
SPECIFICATIONS
Sampling frequencies
MPEG1 Layer-3:
32 kHz/44.1 kHz/48 kHz
MPEG2 Layer-3:
16 kHz/22.05 kHz/24 kHz
MPEG1 Layer-2:
32 kHz/44.1 kHz/48 kHz
Xvid (V4D)
Video codec: Xvid video
Bit rate: 4.854 Mbps (MAX)
Resolution/Frame rate:
720 × 480 30 fps
720 × 576 25 fps
Audio codec: MP3
MPEG4 (V4D)
File format: MP4 File Format
Video codec:
MPEG4 Simple Profile
(AVC is not compatible.)
Bit rate: 4 Mbps
Resolution/Frame rate:
720 × 480 30 fps
720 × 576 25 fps
Audio codec: AAC-LC
(HE-AAC is not compatible.)
DRM: Not compatible
Disc player section
System
Compact disc and digital audio system
(V3)
Compact disc and digital audio and
video system (V4D)
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 μW
* This output is the value
measurement at a distance of
200 mm from the objective lens
surface on the Optical Pick-up
Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Signal-to-noise ratio (V3)
More than 90 dB
Dynamic range (V3)
More than 88 dB
MHC-V3/V4D
Saudi Arabia Model
South African Model
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Name
Video color system format (V4D)
Latin American model: NTSC
Other models: NTSC and PAL
FM tuner section
System
PLL quartz-locked digital synthesizer
Tuning range
87.5 MHz – 108.0 MHz (50 kHz step)
Antenna
FM wire antenna
Bluetooth section
Communication system
Bluetooth Standard version 3.1
Output
Bluetooth Standard Power Class 2
Maximum communication range
Line of sight approx. 10 m
1)
Frequency band
2.4 GHz band (2.4000 GHz –
2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible Bluetooth profiles
2)
A2DP (Advanced Audio Distribution
Profile)
AVRCP 1.3 (Audio Video Remote
Control Profile)
SPP (Serial Port Profile)
Supported codecs
SBC (Sub Band Codec)
AAC (Advanced Audio Coding)
1)
The actual range will vary depending on
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna's performance, operating system,
software application, etc.
2)
Bluetooth standard profiles indicate the
purpose
of
Bluetooth
communication
between devices.
Speaker section
Speaker system
3-way, Sound Pressure Horn
HOME AUDIO SYSTEM
E Model
MHC-V3/V4D
Argentina Model
Malaysia Model
Mexican Model
Thai Model
MHC-V4D
Australian Model
MHC-V3
HCD-GPX555
CDM90-DVBU204//M
CMS-S76RFS7G
Speaker unit
Tweeter L/R: 40 mm, cone type
Mid L/R: 80 mm, cone type
Woofer: 200 mm, cone type
Rated impedance
Tweeter L/R: 2 ohms
Mid L/R: 2 ohms
Woofer: 4 ohms
General
Power requirements
E51 models:
AC 220 V – 240 V, 50 Hz
Other models:
AC 120 V – 240 V, 50/60 Hz
Power consumption
120 W
Dimensions (w/h/d) (Approx.)
280 mm × 786 mm × 280 mm (V3)
280 mm × 792 mm × 280 mm (V4D)
Mass (Approx.)
13.0 kg
Supplied accessories
Remote control (1)
R6 (Size AA) batteries (2)
FM wire antenna (1)
AC power cord (1)
Design and specifications are subject to
change without notice.
– Continued on next page –

Advertisement

Table of Contents
loading

Summary of Contents for Sony MHC-V3

  • Page 1 – Continued on next page – Dynamic range (V3) MPEG2 Layer-3: More than 88 dB 8 kbps – 160 kbps, VBR MPEG1 Layer-2: HOME AUDIO SYSTEM 32 kbps – 384 kbps, VBR 9-890-660-06 Sony Corporation 2015F80-1 © 2015.06 Published by Sony EMCS (Malaysia) PG Tec...
  • Page 2 Bluetooth SIG, Inc. and any use of such marks by Sony 2. A battery-operated AC milliammeter. The Data Precision 245 Corporation is under license. Other trademarks and trade names are those of their respective owners.
  • Page 3: Table Of Contents

    MHC-V3/V4D Ver. 1.5 TABLE OF CONTENTS SERVICING NOTES ..........6-19. Printed Wiring Board - USB Board - ......58 6-20. Schematic Diagram - USB Board - ........ 58 DISASSEMBLY 6-21. Printed Wiring Board - MIC Board (V4D) - ....58 2-1.
  • Page 4: Servicing Notes

    UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. MODELO MHC-V3 (Caution: Some printed circuit boards may not come printed with SISTEMA DE AUDIO PARA EL HOGAR AC 220-240V ~ 50Hz 120W...
  • Page 5 TUNER board is damaged, exchange the entire Bluetooth device. mounted board. For example, select “SONY : MHC-V3/MHC-V4D”. If passkey is required on the Bluetooth device, enter “0000”. NOTE OF REPLACEMENT OF THE MS-476 BOARD 7. Perform the Bluetooth connection on the Bluetooth device.
  • Page 6 MHC-V3/V4D Ver. 1.2 BOND FIXATION OF ELECTRIC PARTS Playing music from a Bluetooth device When DAMP board is replaced or the following object parts are replaced, it is necessary to fi x parts to the boards by using a speci- For a Bluetooth device fi...
  • Page 7 MHC-V3/V4D Ver. 1.1 HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF Note 1: After the side panel and top panel are removed, this work is done. Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
  • Page 8 MHC-V3/V4D Ver. 1.1 CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION Switching Regulator Board (Conductor side view) (MHC-V3/V4D) In checking the Switching Regulator board, make 3 capacitors discharge of C914, C1003 and C1006 for eletrical shock prevention. 800 /5 W 800 /5 W...
  • Page 9: Disassembly

    MHC-V3/V4D Ver. 1.5 SECTION 2 DISASSEMBLY Note: Disassemble the unit in the order as shown below. 2-1. DISASSEMBLY FLOW 2-2. SIDE L, R PANEL (Page 10) 2-3. TOP PANEL BLOCK (Page 10) 2-4. LOADING PANEL BLOCK 2-17. VOLUME KNOB BLOCK...
  • Page 10: Side L, R Panel

    MHC-V3/V4D Ver. 1.3 Note: Follow the disassembly procedure in the numerical order given. 2-2. SIDE L, R PANEL 1 two screws (+BVTP 3 2 two screws (+BVTP 3 4 panel, side L 2 two screws (+BVTP 3 3 Remove the panel, side L in the direction of the arrow.
  • Page 11: Loading Panel Block

    MHC-V3/V4D Ver. 1.1 2-4. LOADING PANEL BLOCK 3 three claws 4 panel, loading block hole – Left view – 2 Draw out the tray. 1 Insert the clip etc. Insert the clip etc. processed to the length of 8 cm or more in the hole CD mechanism deck on the side of the chassis and push.
  • Page 12: Cdm Block

    MHC-V3/V4D Ver. 1.1 2-5. CDM BLOCK 2 four screws 7 CDM block 2 two screws (+BVTP 3 (+BVTP 3 CDM block 4 wire (flat type) (24 core) (CN302) 5 wire (flat type) (5 core) (CN303) 6 CN401 3 Remove the CDM block (6P) in the direction of the arrow.
  • Page 13: Back Panel Block

    MHC-V3/V4D Ver. 1.1 2-6. BACK PANEL BLOCK (V4D) hole 1 CN1004 (2P) hole hook 2 two screws (+BVTP 3 2 one screw (+BVTP 3 hook (V4D) 2 one screw (+BVTP 3 – Top rear view – 2 three screws (+BVTP 3...
  • Page 14: Tuner Board

    MHC-V3/V4D Ver. 1.1 2-7. TUNER BOARD 2 two screws (+BVTP 3 1 wire (flat type) (15 core) (CN852) (V3) wire (flat type) (19 core) (CN853) (V4D) 3 TUNER board (V4D) – Top rear view – Note 2: When you install the connector, please install them correctly.
  • Page 15: Aragon Board

    MHC-V3/V4D Ver. 1.3 2-8. ARAGON BOARD 2 three screws 1 wire (flat type) 3 clamp (L35) (+BVTP 3 2 one screw (17 core) (CN1001) (+BVTP 3 3 clamp (L35) (AUS, SAF, EA, MY) 8 ARAGON board 7 CN115 (5P) 6 wire (flat type)
  • Page 16: Damp Board

    MHC-V3/V4D Ver. 1.1 2-9. DAMP BOARD 6 heat sink 1 CN1006 (4P) 2 CN1007 (3P) 5 two screws (+BVTP 3 4 one screw (+BVTP 3 4 two screws (+BVTP 3 7 DAMP board 3 CN1005 (8P) – Top rear view –...
  • Page 17: Chassis Block

    MHC-V3/V4D Ver. 1.1 2-10. CHASSIS BLOCK 2 three screws 13) (TR-184A)) 2 three screws 13) (TR-184A)) 4 chassis block 1 CN901 (2P) Note: When you install the connector, please install them correctly. There is a possibility that this machine damages when not correctly installing it.
  • Page 18: Bluetooth Module, Smps Board

    MHC-V3/V4D Ver. 1.1 2-11. BLUETOOH MODULE, SMPS BOARD 0 chassis, block 2 wire (flat type) 1 filament tape (10 core) 1 filament tape 3 bluetooth module 4 two screws 6 bracket, chassis (+BVTP 3 7 Remove the wire from holder, wire...
  • Page 19: Front Panel Block

    MHC-V3/V4D Ver. 1.1 2-12. FRONT PANEL BLOCK 2 Insert the jig into a space and slowly remove the panel, front block. Note 1: When using a jig, please work 1 one screw so as not to injure panel, front 13) (TR-184A)) block and speaker cabinet.
  • Page 20: Rc-S801/A5 (Ww), Speaker Led Board, Ir Board, Front Panel Assy

    MHC-V3/V4D Ver. 1.5 2-13. RC-S801/A5 (WW), SPEAKER LED BOARD, IR BOARD, FRONT PANEL ASSY 5 RC-S801/A5 (WW) 3 bracket, NFC 2 one screw (+BVTP 3 1 filament tape 4 wire (flat type) (15 core) qs panel, front assy 0 one screw...
  • Page 21: Loudspeaker (20Cm) (Woofer) (Sp5)

    MHC-V3/V4D Ver. 1.1 2-14. LOUDSPEAKER (20cm) (WOOFER) (SP5) loudspeaker (20cm) terminal position 3 terminal (SP5) (wide side) [grey] 3 terminal (narrow) [black/grey] 1 four screws ((1) (4 X20), +BV TAPPING) 2 Remove the loudspeaker (20cm) (SP5) 4 loudspeaker (20cm) in the direction of the arrow.
  • Page 22: Loudspeaker (8Cm) (Mid: L-Ch) (Sp1), Loudspeaker (8Cm) (Mid: R-Ch) (Sp3)

    MHC-V3/V4D Ver. 1.1 2-15. LOUDSPEAKER (8cm) (MID: L-CH) (SP1), LOUDSPEAKER (8cm) (MID: R-CH) (SP3) terminal position hook loudspeaker loudspeaker (8cm) (SP1) (8cm) (SP3) 4 terminal (wide side) 4 terminal (narrow side) 1 Remove the 8 terminal speaker cable. (wide side)
  • Page 23: Service, Optical Device(7G), Wire (Flat Type)

    MHC-V3/V4D Ver. 1.1 2-16. SERVICE, OPTICAL DEVICE(7G), WIRE (FLAT TYPE) Note : Before disconnecting the wire (fl at type) (24 core) of optical pick-up block, solder the short-land. 2 chuck holder assy (T) 1 six claws qf tape qk tape...
  • Page 24: Volume Knob Block

    MHC-V3/V4D Ver. 1.1 2-17. VOLUME KNOB BLOCK How to install the knob, volume block Note: When installing the knob, volume block, align the two ribs of knob, volume and 2 knob, volume block the shaft. knob, volume block – Bottom view –...
  • Page 25: Test Mode

    MHC-V3/V4D Ver. 1.1 SECTION 3 TEST MODE COLD RESET VERSION DISPLAY It can clears all data including preset data stored in the memory It can confi rm the SC and CD version (V3) / DVD version (V4D). to initial conditions. Execute this mode when returning the unit to Procedure: the customer.
  • Page 26 fl uorescent indicator tube. When pressing the [] button again, the display returns to the Model name for: each version display. MHC-V3 = FSX0 MHC-V4D = FSX0 DVD Screen display 6. Each time [+] / [+ PRESET +]...
  • Page 27 MHC-V3/V4D Ver. 1.1 [HISTORY MODE] This mode is used to check important data stored in the system when PROTECTOR happen. Procedure: 1. During demo mode, press [l m TUNING‒] / [. TUNING‒] button and [ENTER] button for 5 seconds to mode into history mode.
  • Page 28 MHC-V3/V4D Ver. 1.5 [MODEL & DEST WRITE MODE] [DVD COLOR SYSTEM MODE] This mode is used to set software model & destination. • This mode let you change the color system of the video output This mode is only available when no permanent model &...
  • Page 29 MHC-V3/V4D Ver. 1.1 • Execute IOP Measurement • Check Emergency History In order to execute IOP measurement, the following standard To check the emergency history, please follow the following procedures must be followed. procedure. 1. From the Top Menu of Remocon Diagnosis Menu, select 1.
  • Page 30 MHC-V3/V4D Ver. 1.1 • Parameter of error code To return to the Top Menu of Remocon Diagnosis Menu This is the detail of error code. Press the [0] button on the remote commander. • Check Version Information Example of Error code To check the version information, please follow the following 1.
  • Page 31: Electrical Check

    MHC-V3/V4D SECTION 4 Ver. 1.1 ELECTRICAL CHECK TUNER SECTION 0 dB = 1 V FM AUTO STOP CHECK signal generator – Procedure: 1. Turn the power on. 2. Input the following signal from Signal Generator to FM antenna input directly.
  • Page 32 MHC-V3/V4D Ver. 1.1 Checking Location: CD/DVD SECTION -ARAGON Board (CONDUCTOR SIDE)- [TEST DISC LIST] Use the following test disc on test mode. • CD: YEDS-18 (PART No. 3-702-101-01) PATD-012 (PART No. 4-225-203-01) • DVD (SL) NTSC HLX-503 (PART No. J-6090-069-A) HLX-504 (PART No.
  • Page 33: Troubleshooting

    MHC-V3/V4D Ver. 1.1 SECTION 5 TROUBLESHOOTING...
  • Page 34 MHC-V3/V4D Ver. 1.3...
  • Page 35 MHC-V3/V4D Ver. 1.3...
  • Page 36 MHC-V3/V4D Ver. 1.3...
  • Page 37 MHC-V3/V4D Ver. 1.4...
  • Page 38: Diagrams

    MHC-V3/V4D Ver. 1.5 SECTION 6 DIAGRAMS • Circuit Boards Location (V4D) MIC board PANEL board USB board DAMP board TUNER board MS-476 board ARAGON board BLUETOOTH module SMPS board RC-S801/A5 (WW) IR board SPEAKER LED board...
  • Page 39: Block Diagram - Cd/Usb Section

    MHC-V3/V4D Ver. 1.1 6-1. BLOCK DIAGRAM - CD/USB Section - RF AMP SERVO PROCESSOR AUDIO PROCESSOR SERVICE, OPTICAL DEVICE(7G) IC301 >001B ACLK, ADIN ACLK ACLK MAIN SECTION RFIP ADIN (Page 40) ADIN VOA/A RF_C >002B VOB/B RF_B CVBS CVBS CVBS...
  • Page 40: Block Diagram - Main Section

    MHC-V3/V4D Ver. 1.1 6-2. BLOCK DIAGRAM - MAIN Section - >001B MTK-MCK, ADIN CD/USB SECTION (Page 39) >003B BCK, LRCK, ARAGON-MCK AMP SECTION BUS BUFFER (Page 41) IC102 (1/2) MIC AMP CN102 IC2300 BT-RXD BT-RXD(MD-CLK) J2300 MIC 2 BT-TXD BT-TXD...
  • Page 41: Block Diagram - Amp Section

    MHC-V3/V4D Ver. 1.2 6-3. BLOCK DIAGRAM - AMP Section - POWER AMP IC1001 STEREO D/A CONVERTER SPB1 IC611 OP AMP SPK BOX ASSY IC612 VOUTL INPUT_B B_-INPUT A_OUTPUT OUT_A DATA (WOOFER) ARAGON-MCK 16 SCK LRCK 3 LRCK INPUT_A B_OUTPUT OUT_B OUT_C >004B...
  • Page 42: Block Diagram - Panel/Power Supply Section

    MHC-V3/V4D Ver. 1.1 6-4. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section - SYSTEM CONTROLLER REMOTE CONTROL IC101 (4/4) RECEIVER IC7001 PROTECTION CONTROL PCONT-DAMP Q576 PROTECTION CONTROL Q575 +5V REG. VBUS POWER +5.5V REG. (ON/OFF SWITCH) PROTECTION CONTROL S5008 POWER-KEY SPM-C-MON IC001...
  • Page 43 MHC-V3/V4D Ver. 1.5 • Note for Printed Wiring Boards and Schematic Diagrams • Waveforms – ARAGON Board – Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF)
  • Page 44: Aragon Board (Component Side)

    MHC-V3/V4D Ver. 1.4 6-5. PRINTED WIRING BOARD - ARAGON Board (Component Side) - • See page 38 for Circuit Boards Location. • : Uses unleaded solder. ARAGON BOARD (COMPONENT SIDE) SERVICE, OPTICAL DEVICE CONNECT TO (7G) SMPS BOARD BLUETOOTH (CHASSIS)
  • Page 45: Aragon Board (Conductor Side)

    MHC-V3/V4D Ver. 1.4 6-6. PRINTED WIRING BOARD - ARAGON Board (Conductor Side) - • See page 38 for Circuit Boards Location. • : Uses unleaded solder. ARAGON BOARD (CONDUCTOR SIDE) CL403 R108 R109 C404 CL401 Q103 R012 E Q104 IC401...
  • Page 46: Schematic Diagram - Aragon Board (1/6)

    MHC-V3/V4D Ver. 1.4 6-7. SCHEMATIC DIAGRAM - ARAGON Board (1/6) - • See page 60 for IC Block Diagrams. >001S >003S >002S TUNER BOARD TUNER BOARD CN3008 CN3007 ARAGON BOARD (6/6) (Page 57) (Page 51) (Page 57) CN852 CN853 ARAGON BOARD >008S...
  • Page 47: Schematic Diagram - Aragon Board (2/6)

    MHC-V3/V4D Ver. 1.4 6-8. SCHEMATIC DIAGRAM - ARAGON Board (2/6) - • See page 43 for Waveforms. • See page 60 for IC Block Diagrams. • See page 67 for IC Pin Function Descriptions. >020S >007S >008S ARAGON BOARD >005S...
  • Page 48: Schematic Diagram - Aragon Board (3/6)

    MHC-V3/V4D Ver. 1.2 6-9. SCHEMATIC DIAGRAM - ARAGON Board (3/6) - • See page 60 for IC Block Diagrams. ARAGON BOARD (3/6) R433 FE_DVD_LDD CL413 FE_3.3V_1 >015S CL412 R421 ARAGON BOARD CL414 CL415 >022S R422 (2/6) Q402 Q401 2SA2119K ARAGON BOARD...
  • Page 49: Schematic Diagram - Aragon Board (4/6)

    MHC-V3/V4D Ver. 1.4 6-10. SCHEMATIC DIAGRAM - ARAGON Board (4/6) - • See page 60 for IC Block Diagrams. • See page 43 for Waveforms. ARAGON BOARD (4/6) R058 CN001 JL005 R013 13.5V C010 C011 100p 0.1u 13.5V C013 C019 JL006 0.1u...
  • Page 50: Schematic Diagram - Aragon Board (5/6)

    MHC-V3/V4D Ver. 1.4 6-11. SCHEMATIC DIAGRAM - ARAGON Board (5/6) - • See page 60 for IC Block Diagrams. >010S >029S ARAGON ARAGON BOARD BOARD FLASH (1/6) PROGRAMMING (4/6) (Page 46) (Page 49) CN107 ARAGON BOARD (5/6) CN116 C284 0.1u...
  • Page 51: Schematic Diagram - Aragon Board (6/6)

    MHC-V3/V4D Ver. 1.4 6-12. SCHEMATIC DIAGRAM - ARAGON Board (6/6) - • See page 43 for Waveforms. • See page 60 for IC Block Diagrams. • See page 67 for IC Pin Function Descriptions. ARAGON BOARD PCONT-BTSTBY PCONT-BTSTBY >031S (6/6) R113 EVER+3.3V...
  • Page 52: Printed Wiring Board - Panel Board

    MHC-V3/V4D Ver. 1.5 6-13. PRINTED WIRING BOARD - PANEL Board - • See page 38 for Circuit Boards Location. • : Uses unleaded solder. PANEL BOARD S5016 CONNECTION PAIRING BLUETOOTH CL5041 S5003 R5008 R5009 ENTER R5007 D5003 Q5003 JR509 C5011...
  • Page 53: Schematic Diagram - Panel Board

    MHC-V3/V4D Ver. 1.2 6-14. SCHEMATIC DIAGRAM - PANEL Board - • See page 60 for IC Block Diagrams. ND5001 PANEL BOARD LIQUID CRYSTAL DISPLAY S5008 " / 1 SEG24 SEG12 SEG24 SEG12 SEG25 SEG11 S5009 SEG25 SEG11 SEG26 SEG10 SEG26...
  • Page 54: Printed Wiring Board - Damp Board

    MHC-V3/V4D Ver. 1.4 6-15. PRINTED WIRING BOARD - DAMP Board - • See page 38 for Circuit Boards Location. • : Uses unleaded solder. DAMP BOARD DAMP BOARD (COMPONENT SIDE) (CONDUCTOR SIDE) SPB1 SPK BOX ASSY (WOOFER) (TWEETER (R-CH)) (TWEETER (L-CH))
  • Page 55: Schematic Diagram - Damp Board

    MHC-V3/V4D Ver. 1.4 6-16. SCHEMATIC DIAGRAM - DAMP Board - • See page 60 for IC Block Diagrams. DAMP BOARD Q1018 Q1019 KTA1542T-RTK/P R1128 1 V1 PBSS4160T AMP RESET SWITCH 4.7k AMP RESET SWITCH CL1031 3 V1 R1129 C1136 4 V1...
  • Page 56: Printed Wiring Board - Tuner Board

    MHC-V3/V4D Ver. 1.4 6-17. PRINTED WIRING BOARD - TUNER Board - • See page 38 for Circuit Boards Location. • : Uses unleaded solder. TUNER BOARD (COMPONENT SIDE) J001 J002 AUDIO IN VIDEO OUT ANTENNA (CHASSIS) (CHASSIS) CN3002 C3037 C3038...
  • Page 57: Schematic Diagram - Tuner Board

    MHC-V3/V4D Ver. 1.2 6-18. SCHEMATIC DIAGRAM - TUNER Board - • See page 60 for IC Block Diagrams. TUNER BOARD IC3003 MM3411A33URE IC3003 C3009 L3004 FB003 R3021 22nH +3.3V REG. JL002 C3001 JL006 R3009 R3018 C3006 C3010 C3011 C3013 C3002 0.0022u...
  • Page 58: Printed Wiring Board - Usb Board

    MHC-V3/V4D Ver. 1.5 6-19. PRINTED WIRING BOARD - USB Board - 6-21. PRINTED WIRING BOARD - MIC Board (V4D) - • • • See page 38 for Circuit Boards Location. : Uses unleaded solder. • See page 38 for Circuit Boards Location.
  • Page 59: Schematic Diagram - Mic Board (V4D)

    MHC-V3/V4D Ver. 1.2 6-22. SCHEMATIC DIAGRAM - MIC Board (V4D) - MIC BOARD CN2300 >037S CL2300 A+9V CL2301 TUNER MIC GND CL2302 BOARD MIC SIGNAL CN3003 CL2305 MIC DETECT R2305 (Page 57) CL2310 CL2314 C2301 1.5k D2300 R2301 R2314 C2320 0.1u...
  • Page 60: Printed Wiring Board - Ir Board

    MHC-V3/V4D Ver. 1.4 6-23. PRINTED WIRING BOARD - IR Board - 6-25. PRINTED WIRING BOARD - SPEAKER LED Board - • • • See page 38 for Circuit Boards Location. : Uses unleaded solder. • See page 38 for Circuit Boards Location.
  • Page 61 MHC-V3/V4D Ver. 1.5 • IC Block Diagrams IC102 TC74VHC126FT (EK) (ARAGON BOARD (5/6)) IC103 BU4229F-TR (ARAGON BOARD (5/6)) VOUT – Vref IC106 MX25L3235EM2I-10G (ARAGON BOARD (6/6)) Address Generator Memory Array Page Buffer SO/SIO1 HOLD/SIO3 Data Register Y-Decoder SRAM Buffer WP/SIO2...
  • Page 62 MHC-V3/V4D Ver. 1.5 IC302 W25Q32BVSSIG-R (ARAGON BOARD (2/6)) (V4D) IC302 W25Q16CVSSIG-R (ARAGON BOARD (2/6)) (V3) Write Control Logic _HOLD Status Register High Voltage Generators Page Address Latch / Counter Command and Column Decode Control Logic and 256 Byte Page Buffer...
  • Page 63 MHC-V3/V4D Ver. 1.5 IC401 AM5890S (ARAGON BOARD (3/6)) Vcc2 Voltage Detection MUTE Actuator Spindle Driver (6X) Driver (4X) Thermal Shut down Vcc2 Vcc2 Vcc1 Sled Actuator Driver (4X) Driver (6X) Pre-DRV TRAY DRIVER IC453 TPS2553DBVR (ARAGON BOARD (4/6)) REVERSE VOLTAGE COMPARATOR –...
  • Page 64 MHC-V3/V4D Ver. 1.5 IC606 PCM1808PWR (ARAGON BOARD (1/6)) (V4D) IC609 PCM1808PWR (ARAGON BOARD (1/6)) LRCK Serial Interface DOUT Mode/ Format Control Clock SCKI Timing Control x1/64 Decimation Filter with High Pass Filter DGND Delta Sigma Delta Sigma Modulator Modulator Power...
  • Page 65 MHC-V3/V4D Ver. 1.5 IC1001 TAS5630BPHDR (DAMP BOARD) OC_ADJ 1 VREG CLIP READY OTW1 OTW2 POWER-UP RESET TEMP GVDD_A GVDD_C SENSE GVDD_B GVDD_D RESET 2 OVER-LOAD CURRENT CB3C PROTECTION SENSE STARTUP CONTROL C_STARTUP 3 PVDD_X PPSC OUT_X GND_X OSCILLATOR GVDD_A ACTIVITY...
  • Page 66 MHC-V3/V4D Ver. 1.5 IC5001 BU9795AKS2 (PANEL BOARD) SEG23 COM2 1 SEG22 COM3 2 NC_37 LCD voltage generator Segment NC_3 3 Common driver driver SEG21 VLCD 4 – SEG20 VDD 5 LCD BIAS SELECTOR Common Blink timing SEG19 VSS 6 DDRAM...
  • Page 67 MHC-V3/V4D Ver. 1.5 IC3004 SN74LV4052APWR (TUNER BOARD) IC3005 NJM41031F1 (TE2) (TUNER BOARD) (V4D) POWER SAVE 1 DRIVER VOUT 2 6 dB CLAMP VSAG 3...
  • Page 68 MHC-V3/V4D Ver. 1.1 • IC Pin Function Descriptions ARAGON BOARD (6/6) IC101 R7S7200022CFP (SYSTEM CONTROLLER) Pin No. Pin Name Description Not used VIDEO-MUTE Muting Control for Video CDM-UNLOAD-SW CDM UNLOAD SW CDM-LOAD-SW CDM LOAD SW BT-RESET Reset signal output to the Bluetooth module “H”: reset Not used Power supply terminal (+3.3V)
  • Page 69 MHC-V3/V4D Ver. 1.1 Pin No. Pin Name Description SSI1_DI Data In Signal from ADC to Aragon PCONT-BTSTBY BT Standby Power Control Pin. “H”: ON PCONT-PSAVE-PRO- Main power on/off control signal output “H”:power on TECT Power supply terminal (+3.3V) Main_on Main support on control...
  • Page 70 MHC-V3/V4D Ver. 1.1 Pin No. Pin Name Description PVcc Power supply terminal (+3.3V) TEST-MON4/SD_D0_0 Test port for software checking. ANALOG-CSEL/ Multiplexer selector C for Analog input SD_D1_0 RGB-TRANS-LED- Transfer signal to RGB driver (driver for Speaker LED) SPK/SD_WP_0 LCDBCK_LED LCD Backlight...
  • Page 71 MHC-V3/V4D Ver. 1.1 Pin No. Pin Name Description Ground terminal MTK-POWER-CTRL Power Control pin for MTK C-CONT Trigger port to start charging of SPM Q-Flash-SIO2 Two-way serial data with to the serial fl ash Q-Flash-SIO3 Two-way serial data with to the serial fl ash Q-Flash-CLK Serial data transfer clock signal output to the serial fl...
  • Page 72 MHC-V3/V4D Ver. 1.1 ARAGON BOARD (2/6) IC301 CXD90013R (RF AMP SERVO PROCESSOR AUDIO PROCESSOR) (V3) Pin No. Pin Name Description RF_C RF main beam (A) input from the optical pick-up block RF_D RF main beam (D) input from the optical pick-up block...
  • Page 73 MHC-V3/V4D Ver. 1.1 Pin No. Pin Name Description DQM0 Data mask signal output to the SD-RAM (lower byte) 62 to 69 RD15 to RD8 Two-way data bus with the SD-RAM DQM1 Data mask signal output to the SD-RAM (upper byte) DVDD33 Power supply terminal (+3.3V) (digital system)
  • Page 74 MHC-V3/V4D Ver. 1.1 ARAGON BOARD (2/6) IC301 CXD9990R (CD RF AMP FOCUS/TRACKING ERROR AMP CD SYSTEM PROCESSOR DIGITAL SERVO PROCESSOR) (V4D) Pin No. Pin Name Description RF_C RF main beam C input from the optical pick-up block RF_D RF main beam D input from the optical pick-up block...
  • Page 75 MHC-V3/V4D Ver. 1.1 Pin No. Pin Name Description DQM0 Data mask signal output to the SD-RAM 62 to 69 RD15 to RD8 Two-way data bus with the SD-RAM DQM1 Data mask signal output to the SD-RAM DVDD33 Power supply terminal (+3.3V)
  • Page 76: Exploded Views

    MHC-V3/V4D Ver. 1.5 SECTION 7 EXPLODED VIEWS Note: • The mechanical parts with no reference • Abbreviation The components identifi ed by mark 0 number in the exploded views are not sup- : Argentina model or dotted line with mark 0 are critical for : Australian model plied.
  • Page 77: Loading Panel Section

    MHC-V3/V4D Ver. 1.5 7-2. LOADING PANEL SECTION top panel section (V4D) CDM block section back panel section not supplied not supplied not supplied supplied supplied Ref. No. Part No. Description Remark X-2589-368-1 PANEL, LOADING ASSY 4-536-754-01 SPRING (LP) 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3...
  • Page 78: Back Panel Section

    MHC-V3/V4D Ver. 1.1 7-3. BACK PANEL SECTION not supplied (V4D) (V4D) ARAGON board section Ref. No. Part No. Description Remark 0 M1 1-855-006-41 FAN, DC 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3...
  • Page 79: Aragon Board Section

    MHC-V3/V4D Ver. 1.5 7-4. ARAGON BOARD SECTION (AUS, SAF, EA, MY) not supplied (TUNER board) (V4D) not supplied chassis section Note: If wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.
  • Page 80: Chassis Section

    MHC-V3/V4D Ver. 1.1 7-5. CHASSIS SECTION not supplied not supplied not supplied not supplied not supplied not supplied not supplied supplied not supplied not supplied not supplied not supplied not supplied not supplied speaker cabinet section Note: If wire (fl at type) is replaced, install it after bending front panel section it in the same form as that before replacement.
  • Page 81: Front Panel Section

    MHC-V3/V4D Ver. 1.5 7-6. FRONT PANEL SECTION not supplied not supplied (AUS, SAF, EA, MY) supplied not supplied not supplied (IR board) not supplied not supplied not supplied not supplied not supplied (SPEAKER LED board) Note: If wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.
  • Page 82: Speaker Cabinet Section

    MHC-V3/V4D Ver. 1.5 7-7. SPEAKER CABINET SECTION not supplied not supplied (AUS, SAF, EA, MY) supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-238-407-12 SCREW (1) (4 X20), +BV TAPPING 4-541-367-01 CUSHION, FOOT 4-874-614-12 SCREW (1) (3.5X14), TAPPING...
  • Page 83: Top Panel Section

    MHC-V3/V4D Ver. 1.3 7-8. TOP PANEL SECTION not supplied (AUS, SAF, EA, MY) not supplied not supplied not supplied (PANEL board) supplied not supplied not supplied not supplied (V4D) not supplied ND5001 supplied not supplied (MIC board) (V4D) not supplied not supplied Note: If wire (fl...
  • Page 84: Cdm Block Section

    MHC-V3/V4D Ver. 1.1 7-9. CDM BLOCK SECTION CD mechanism section (CDM90-DVBU204//M) not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-345-115-01 SCREW (S), FLOAT 4-533-382-01 INSULATOR 4-535-577-01 STEP SCREW M2.6...
  • Page 85: Cd Mechanism Section (Cdm90-Dvbu204//M)

    MHC-V3/V4D Ver. 1.4 7-10. CD MECHANISM SECTION (CDM90-DVBU204//M) supplied (including MS-476 board) not supplied not supplied not supplied not supplied not supplied (MS-476 board) not supplied not supplied (AUS, SAF, EA, MY) Note: If fl exible fl at cable and wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.
  • Page 86: Electrical Parts List

    MHC-V3/V4D Ver. 1.5 SECTION 8 ARAGON ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • SEMICONDUCTORS The components identifi ed by mark 0 the parts list may be different from the In each case, u: μ, for example: or dotted line with mark 0 are critical for parts specifi...
  • Page 87 MHC-V3/V4D Ver. 1.1 ARAGON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C127 1-164-850-11 CERAMIC CHIP 10PF 0.5PF C331 1-118-386-11 CERAMIC CHIP 0.1uF C128 1-116-717-11 CERAMIC CHIP 10uF C334 1-118-459-11 CERAMIC CHIP 0.01uF * C129 1-118-035-11 CERAMIC CHIP 0.1uF...
  • Page 88 MHC-V3/V4D Ver. 1.4 ARAGON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C642 1-164-874-11 CERAMIC CHIP 100PF 50V (V4D) CN106 1-779-806-21 CONNECTOR 8P (V4D) C644 1-164-874-11 CERAMIC CHIP 100PF 50V (V4D) C645 1-124-779-00 ELECT CHIP 10uF...
  • Page 89 MHC-V3/V4D Ver. 1.4 ARAGON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC301 (Not supplied) IC CXD9990R (V4D) R014 1-216-864-11 SHORT CHIP IC301 6-718-440-01 IC CXD90013R (V3) R015 1-216-864-11 SHORT CHIP IC302 (Not supplied) IC W25Q32BVSSIG-R (V4D)
  • Page 90 MHC-V3/V4D Ver. 1.2 ARAGON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R125 1-218-973-11 METAL CHIP 1/16W R198 1-218-990-81 SHORT CHIP R126 1-218-990-81 SHORT CHIP R200 1-218-990-81 SHORT CHIP R127 1-218-965-11 METAL CHIP 1/16W R201 1-218-941-81...
  • Page 91 MHC-V3/V4D Ver. 1.2 ARAGON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R274 1-218-941-81 METAL CHIP 1/16W R349 1-218-941-81 METAL CHIP 1/16W R278 1-218-941-81 METAL CHIP 1/16W R350 1-218-990-81 SHORT CHIP R279 1-218-941-81 METAL CHIP 1/16W...
  • Page 92 MHC-V3/V4D Ver. 1.2 ARAGON Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * R430 1-250-572-11 METAL CHIP 1/10W R851 1-218-990-81 SHORT CHIP R431 1-218-973-11 METAL CHIP 1/16W R853 1-218-990-81 SHORT CHIP R432 1-218-941-81 METAL CHIP 1/16W...
  • Page 93 MHC-V3/V4D Ver. 1.4 DAMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-2037-670-A DAMP BOARD, COMPLETE (V3) C1089 1-117-681-11 ELECT CHIP 100uF A-2049-077-A DAMP BOARD, COMPLETE (V4D) * C1090 1-118-360-11 CERAMIC CHIP 0.1uF ********************* C1091 1-117-681-11...
  • Page 94 MHC-V3/V4D Ver. 1.4 DAMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark L1004 1-457-077-21 AIR-CORE COIL R1071 1-216-821-11 METAL CHIP 1/10W L1006 1-482-158-11 INDUCTOR 10uH R1072 1-216-821-11 METAL CHIP 1/10W L1007 1-482-158-11 INDUCTOR 10uH R1073 1-216-827-11 METAL CHIP 3.3K...
  • Page 95 MHC-V3/V4D Ver. 1.2 MS-476 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MIC BOARD (V4D) R2307 1-216-833-11 METAL CHIP 1/10W ********** R2308 1-216-833-11 METAL CHIP 1/10W R2309 1-216-845-11 METAL CHIP 100K 1/10W < CAPACITOR >...
  • Page 96 MHC-V3/V4D Ver. 1.2 PANEL SPEAKER LED TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JR504 1-216-296-11 SHORT CHIP < SWITCH > JR505 1-216-296-11 SHORT CHIP S5001 1-762-875-21 SWITCH, TACTILE (DJ EFFECT) JR506 1-216-296-11 SHORT CHIP...
  • Page 97 MHC-V3/V4D Ver. 1.2 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3036 1-164-874-11 CERAMIC CHIP 100PF R3031 1-218-973-11 METAL CHIP 1/16W C3037 1-118-373-11 CERAMIC CHIP 0.01uF R3032 1-218-973-11 METAL CHIP 1/16W C3038 1-118-289-11 CERAMIC CHIP 0.1uF...
  • Page 98 MHC-V3/V4D Ver. 1.5 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R6002 1-216-864-11 SHORT CHIP 4-540-486-22 MANUAL, INSTRUCTION (SPANISH) ************************************************************* (V4D: E2, E51) 4-540-486-32 MANUAL, INSTRUCTION (FRENCH, ARABIC) MISCELLANEOUS (V4D: EA, E4) ************** 4-540-486-41 MANUAL, INSTRUCTION (PORTUGUESE) (E4)
  • Page 99 Change screw type from (3.5 x 14), tapping to (4 x 13) (TR-184A) in page 17 and 19. Delete CUSHION, SEAL in page 79 and 83. Delete of Ref. No. 353 and 354 in page 83 for 120 V AC area in E model (MHC-V3), Chilean and Peruvian models (MHC-V3).
  • Page 100 MHC-V3/V4D Ver. Date Description of Revision 2015.03 Additional of Mexican, Chilean and Peruvian models (MHC-V4D). Change all model label P/N at page 4. Change description of IC102 in ARAGON board. Change of DAMP, IR, SPEAKER LED and TUNER boards (Suffi x 13).

This manual is also suitable for:

Mhc-v4d

Table of Contents