Gas Supply Pressures; Fan Kit; Fan Removal Instructions; Installation Of Trim Switch For Rn/Rp Gas Valves - Vermont Castings LHECDV30 Homeowner's Installation And Operating Manual

1/2" Gas Supply
1/2" x 3/8" Shut Off Valve
FP297
Fig. 4 Typical gas supply installation.

Gas Supply Pressures

This heater must be isolated from the gas supply piping
system by closing its individual manual shut-off valve
during any pressure equal to or less than 1/2 psig
(3.45kPa).
The heater and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.45kPa).

Fan Kit

115 volt, 60 Hz. 56w (Model FK24)
NOTE: The LHERDV20 and LHERDV30 are not
designed for a fan kit.
The fan kit includes the following: fan, temperature
sensor, speed control and a 6 ft. cord. The following
explains how to start and set the fan for automatic
operation.
1. Plug in the electrical cord.
2. Start gas fire - see lighting procedures.
3. Turn on fan speed control.
4. Wait until the unit has warmed up sufficiently to
activate the temperature sensor, approx. 5-10
minutes.
5. Once fan starts, adjust speed control to desired fan
speed. The fan will now automatically come on every
time the fireplace is in operation. Should the fan not
be needed simply turn off the speed control.
The appliance, when installed must be
electrically connected and grounded in
accordance with local codes or, in the ab-
sence of local codes, with the current CSA
C22.1 Canadian Electrical Code.
U.S. Installations, follow local codes and the
National Electrical Code, ANSI/NFPA No. 70.
Should this fan require servicing, the
power supply must be disconnected. For
rewiring of any replacement components
refer to Figure 6.
10004894
3/8" Nipple
3/8" Union
3/8" Nip-
ple
FP297
INSTA VENT FREE
R MODEL GAS SUPPLY
8/24/96
LHEDV Series Direct Vent Insert

Fan Removal Instructions

1. Turn off gas and electricity.
2. Remove the front glass.
3. Remove the logs.
CAUTION: Logs may be hot!
4. For Model LHECDV20: remove burner assembly
and bracket rear log. For Model LHECDV30: remove
bracket rear log and cover fan.
5. Remove the fan mounting nuts (2 nuts). (Fig. 5)
6. Slip off the electrical connector at the motor.
7. Lift out the fan.
8. To reinstall reverse procedure.
Thermal Sensor is
Attached to Burner
Base
Screw Stud
Fan Speed Control/Junction Box
Fig. 5 Fan location.
Temperature Sensor
Speed
Control
Black
White
Ground
Fig. 6 Wiring diagram RN/RP. NOTE: For comfort valve wir-
FP394
ing diagram refer to Page 18, Figure 27.
WIRING DIAGRAM
Installation of Trim Switch 11/20/96
for RN/RP Gas Valves
1. Thread wire through openings on the right side of fire-
place. Do not cut wire or insulation on metal edges.
2. Insert ON/OFF switch with wiring assembly into the
bracket switch with the pre-punched opening mounted
on the right side of the trim. (Fig. 7)
3. For left side installation, relocate the bracket switch
to the left side of the trim kit and repeat Step 2. (Fig.
8)
4. Connect wiring from the switch to the gas valve (Fig.
9a & b).
Fan is Installed
at the Back of the
Air Intake Box
FP1252
Fan
FP1252
FK24 install
1/03
FP394
Screw
Stud
7