Vermont Castings LHERDV20 Owners Installation And Operating Manual
Vermont castings direct vent insert - homeowner's installation and operating manual
Hide thumbs
Also See for LHERDV20:
- Specification (8 pages) ,
- Homeowner's installation and operating manual (32 pages)
Table of Contents
Advertisement
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE
WARNING!
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
E X A C T LY,
A
EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS
OF LIFE.
FOR YOUR SAFETY
Installation and service must
be performed by a qualified
installer, service agency or the
gas supplier.
WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electric switch;
do not use any phone in your
building.
•
Immediately call your gas supplier
from your neighbor's phone. Follow
the gas suppliers instructions.
•
If you cannot reach your gas
supplier call the fire department.
DO NO�� ���OR�� OR ����
O�� ���OR�� OR ����
GA�OLIN�� OR O��H��R
FLAMMABL�� VAPOR� AND
LIQ�ID� IN ��H�� VICINI��Y OF
��HI� OR ANY O��H��R
APPLIANC��.
F I R E
O R
Direct Vent Insert
Models: LHERDV20
LHERDV30
LHECDV20
LHECDV30
Homeowner's Installation and
Operating Manual
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
C E R T I F I E D
10004894 1/13 Rev. 8
Advertisement
Table of Contents
Related Manuals for Vermont Castings LHERDV20
Summary of Contents for Vermont Castings LHERDV20
-
Page 1: Direct Vent Insert
SAFETY INFORMATION PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE Direct Vent Insert WARNING! Models: LHERDV20 IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED LHERDV30 E X A C T LY, F I R E EXPLOSION MAY RESULT... -
Page 2: Table Of Contents
PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING THIS APPLIANCE. Thank you and congratulations on your purchase of an Vermont Castings Group fireplace insert. IMPORTANT - Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the manufacturers' warranty. -
Page 3: General Information, Warnings, Cautions
�.�. Installations follow local codes and/or the current National Fuel Gas Code AN�I Z3.1/NFPA 54. LHECDV20 / LHERDV20 In the Commonwealth of Massachusetts, all gas fittings and in- LHEDV30 / LHERDV30 stallation of this heater shall only be done by a licensed gas fitter Certified To or licensed plumber. -
Page 4: Requirements For The Commonwealth Of Massachusetts
LHEDV Series Direct Vent Insert Installation & Operating Instructions Requirements for the Commonwealth of Inspection Massachusetts ��he state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the All gas fitting and installation of this heater shall only be installation unless, upon inspection, the inspector observes done by a licensed gas fitter or licensed plumber. -
Page 5: Fireplace
NOTE: LH���LGA is only available for 4 = LH��ACN�� FP1248 �� - Firebox width at insert depth(�) Model LH��C30 and LH��R30 5 = LH����CK Minimum fireplace opening LHECDV20 LHERDV20 LHECDV30 LHERDV30 1/03 0⁷⁄₈" (530 mm) 0⁷⁄₈" (530 mm) 6³⁄₄" (680 mm) 6³⁄₄"... -
Page 6: Locating Your Fireplace Insert
LHEDV Series Direct Vent Insert Locating Your Gas Fireplace Insert Framing & Finishing with Zero Clearance Kit For Zero Clearance Kit applications, it is important to determine the finished facing material before beginning to frame. ��his will allow for the thickness of the finishing material between the frame and the fireplace trim. -
Page 7: Zero Clearance Applications
ANSI Z223.1/NFPA 54 and/or local codes having VCAK chimney adapter kit installation. When using the jurisdiction. HEZC with insert models LHECDV20 or LHERDV20, the In Canada, please consult provincial and/or local Trim Closure Kit, LHE20TCK, must also be installed. -
Page 8: Gas �Upply Pressures
LHEDV Series Direct Vent Insert ��he gas control is equipped with a captured screw type The appliance, when installed must be electri- pressure test point, therefore it is not necessary to provide cally connected and grounded in accordance a 1/8" test point up stream of the control. with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian When using copper or flex connector, use only approved... -
Page 9: Installation Of
LHEDV Series Direct Vent Insert Honeywell Valve Installation of Trim Switch for RN/RP Gas Valves 1. ��hread wire through openings on the right side of fire- place. Do not cut wire or insulation on metal edges. . Insert ON/OFF switch with wiring assembly into the bracket switch with the pre-punched opening mounted on the right side of the trim. -
Page 10: Liner Installation
LHEDV Series Direct Vent Insert WARNING Flue gas exits through the vent Some factory-built fireplaces have air passages 1) Attach flexible pipe termination rain to rain cap on face of fireplace for zero clearance capabilities. ) �ecure with clamp Under no circumstances should these passages be 3) Attach raincap to vent termiantion using Outside combustion... - Page 11 LHEDV Series Direct Vent Insert Flue gas exits Damper through the vent 3" Flex Vent termination rain ��wo Pieces 1) Attach flexible pipe to rain cap ) �ecure with clamp Clamps & 3) Attach raincap to �crew vent termination using Outside combus- three screws tion air enters...
-
Page 12: Round Vent
LHEDV Series Direct Vent Insert Round Vent Termination Installation Ceramic Refractory Installation Round Vent ��ermination Model H��DVR�� is designed 1. Remove front glass. to be installed onto the LH��CDV0, LH��RDV0, LH- . Remove logs from unit. ��CDV30 and LH��RDV30 direct vent insert fireplaces. 3. -
Page 13: Venting Components
LHEDV Series Direct Vent Insert Venting Components 8" x 1" Vent ��ermination Kit Model: H��DV�� (8" x 1" ) (Fit typical 8" x 1" and 9" x 13" flue tile) Kit Includes: A - 8" x 1" Vent ��ermination (x1) B - �tainless �teel Clamps (x4) C - Hardware Package (x1) 1"... -
Page 14: Operating Instructions
LHECDV20, LHERDV20 (Fig. ) cling to the glass surface. Also initial paint curing may deposit a. Place rear left log (JR7). �se the log's bottom holes a slight film on the glass. -
Page 15: Large Lava Rock Placement
LHEDV Series Direct Vent Insert d. Place the front right log (JR10). Position the Figure 22 log notch against the third grate from the right, LH��CDV0 and LH��RDV0 and the other edge of the log on top of the rear right log notch. ��nsure the log is secure in place. -
Page 16: Flame Characteristics
LHEDV Series Direct Vent Insert Flame Characteristics First Firing �pon completing the gas line connection, a small amount It is important to periodically perform a visual check of the of air will be in the lines. When first lighting unit with pilot pilot and the burner flames. -
Page 17: Lighting & Operating Instructions
LHEDV Series Direct Vent Insert Lighting and Operating Instructions FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. ��his heater has a pilot which must be lit manually. When •... -
Page 18: Roubleshooting Gas Control (80 Millivolt Gas Valve)
LHEDV Series Direct Vent Insert Troubleshooting the Gas Control System SIT NOVA 820 Millivolt Valve NOTE: Before trouble shooting the gas control system, be sure external gas shut off is in the “On” position. WARNING: Before doing any gas control service work, remove glass front. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION... -
Page 19: Roubleshooting Gas Control (Honeywell)
LHEDV Series Direct Vent Insert Troubleshooting the Gas Control System Honeywell Millivolt Valve START CHECK Gas Supply On Supply Line Hooked Up Shutoff Valve Open Lockout Has Engaged. Wait 60 Seconds And Try Again. For Spark At Electrode While Pilot Lights With Depressing Piezo —... -
Page 20: Instructions For Rf Comfort Control Valve
LHEDV Series Direct Vent Insert 7. If the manual switch is in the LOCAL position, the valve Instructions for RF Comfort Control Valve will be at the highest fixed pressure setting. ��he trans- mitter will control the fan only. ��he Comfort Control Valve allows remote control of tem- Shut Off Procedure perature, fan and flame appearance. - Page 21 LHEDV Series Direct Vent Insert Delay Timer Mode Pilot As- sembly ��he shut off delay timer has a maximum of hours and a minimum of zero minutes. ��o change the timer level, press the time key followed by an arrow key. Pushing the key once will change the timer by 10 minutes.
- Page 22 LHEDV Series Direct Vent Insert . �lide the Remote/Local switch to R��MO���� and teach the valve a transmitter (refer to Item 6, page 1). ��he ��r- Auto Path ror Code will clear itself after approximately 1¹⁄x minutes and return to normal operation. If the manual switch is set to R��MO����, press Move switch...
- Page 23 LHEDV Series Direct Vent Insert Comfort Valve system control sequence of operation with transmitter �et manual switch Five minute wait to local or remote period Light pilot burner Did the L��D stop Review L��D fail- blinking? ure analysis Release pilotstat knob Cycle switch once and leave in...
-
Page 24: Maintenance
LHEDV Series Direct Vent Insert Maintenance Burner and Burner Compartment In order to properly clean the burner and pilot assembly, turn off the gas to the unit, remove the window frame panel It is important to keep the burner and the burner compartment and logs exposing the burner and pilot assembly. - Page 25 9 a/b 22a/b 12a/b 28/29 24a/b 23 a/b • 4894 Vermont Castings Group reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. LHEDV Series 4894 LHEDV parts 10004894 4/03...
- Page 26 LHEDV Series Direct Vent Insert LHEDV Series (continued) Ref. Description LHERDV20 LHECDV20 LHERDV30 LHECDV30 Log �et Complete 1000533 1000533 10004866 10004866 Log Rear Left 10005333 (JR7) 10005333 (JR7) 10004874 (KR) 10004874 (KR) Log Rear Right 10005334 (JR8) 10005334 (JR8) 10004875 (KR3)
- Page 27 LHEDV Series Direct Vent Insert LHE Series (continued) Ref. Description LHER20 LHEC20 LHER30 LHEC30 Remote �witch (for RN or RP �nits) 53606 53606 53606 53606 Remote Wire Harness w/��erminals (for RN or RP �nits) 100058 100058 100058 100058 Ceramic Fiber Brick FP (Optional) J��1��R0 J��1��C0 K��1��R0...
-
Page 28: Optional Accessories
LHEDV Series Direct Vent Insert Optional Accessories Trim Options Remote Controls Optional remote control units are available to control dif- Face Kits ferent functions of the appliance. NOTE: One is required for LH��C0 and LH��C30 Model Function(s) Controlled Model Description ON/OFF LH��C0FB Louvre ��&B, Black... - Page 29 LHEDV Series Direct Vent Insert 10004894...
- Page 30 LHEDV Series Direct Vent Insert 10004894...
-
Page 31: Warranty
Vermont Castings Group will, at its option, replace or repair the defective components at no charge to the original owner. Vermont Castings Group will also pay for reasonable labor costs incurred in replacing or repairing such components for a period of two years from date of installation. Any products presented for warranty repair must be accompanied by a dated proof of purchase. -
Page 32: Energuide
Fireplace Efficiency (%) Fan-OFF Fan-ON (AFUE%) LH��CDV0RN 61.3 LH��CDV0RP 61.3 LH��CDV0RFN 61.3 LH��CDV30RFP 61.3 LH��RDV0RN 59.7 LH��RDV0RP 59.7 LH��CDV30RN 61.5 LH��CDV30RP 61.5 LH��CDV30RFN 61.5 LH��CDV30RFP 61.5 LH��RDV30RN 64.1 LH��RDV30RP 64.1 Vermont Castings Group 149 Cleveland Drive • Paris, Kentucky 40361 www.vermontcastingsgroup.com...