Advertisement
Quick Links
Install
HIIT Console Wall Power Upgrade Install Instructions
Enhanced Images: Pictures can be zoomed in to any level for detail.
Use the standard zoom tools for your platform to zoom in.
HIIT UB
STEP 1: Remove the mast grommet then use a
3mm allen key to remove the two (2) M6 x 16mm
screws securing the user right shroud to the frame.
STEP 3: Connect the end of the HIIT Console Wall
Power adapter to the end of the Console Power
Cable
Applies to: Airfit, Airfit UB, HIIT Bike, HIIT UB, HIITMill, HIITMill X, HIIT Rower
STEP 2: Remove the user right side shroud by us-
ing a #2 phillips screwdriver to remove the three
(3) #8-18 x 1.25" screws then use a 3mm allen
key to remove the two (2) M5 x 16mm screws.
Finally, use a 5mm allen key to remove the one
(1) M8 x 20mm screw securing the shroud to the
STEP 4: Replace the user right side shroud removed
in Step 2, then route the Console Power Cable down
the frame and out of the bottom of the shroud - as
indicated by the bold line. Use a cable tie to secure
the Console Power Cable to the frame, indicated by
the arrow Finally, connect the power adapter to the
Console Power Cable.
frame.
Page 1
620-8587 Rev. C
Advertisement
Related Manuals for Schwinn Airfit
Summary of Contents for Schwinn Airfit
- Page 1 Install HIIT Console Wall Power Upgrade Install Instructions Applies to: Airfit, Airfit UB, HIIT Bike, HIIT UB, HIITMill, HIITMill X, HIIT Rower Enhanced Images: Pictures can be zoomed in to any level for detail. Use the standard zoom tools for your platform to zoom in.
- Page 2 Install Airfit UB STEP 1: Remove the mast grommet then use a 3mm STEP 2: Remove the user right side shroud by using a allen key to remove the two (2) M6 x 16mm screws #2 phillips screwdriver to remove the three (3) #8-18 securing the user right shroud to the frame.
- Page 3 Install STEP 5: Use a #2 phillips screwdriver to remove the STEP 6: Use a #2 phillips screwdriver to remove the five (5) 8-18 x 3/4” screws (3 securing the shroud, 2 four (4) 8-18 x 3/4” screws securing the user right securing the shroud bracket) then use a 3mm allen boom shroud to the user left boom shroud then key to remove the three (3) M5 screws securing the...
- Page 4 Install STEP 9: Route the Console Power Cable down the frame and out of the bottom of the shroud - as indicated by the bold line. Use a cable tie to secure the Console Power Cable to the frame, indicated by the arrow.
- Page 5 Install HIIT Bike STEP 1: Using a #2 phillips screwdriver, remove STEP 2: Using a #2 phillips screwdriver, remove the two (2) M5 x 10mm screws securing the user the two (2) M5 x 10mm screws securing the user right side fan shroud to the frame then remove the right side fan shroud to the frame then remove the shroud.
- Page 6 Install Airfit Bike STEP 1: Using a #2 phillips screwdriver, remove STEP 2: Remove the HIIT Console Adapter Cable the two (2) M5 x 10mm screws securing the user then connect the long Console Power Cable (the right side fan shroud to the frame then remove the short cable is used for the HIITMills) to the Console shroud.
- Page 7 Install HIITMill + HIITMill X STEP 1: Remove the brake cover using a 4mm allen STEP 2: Connect the Console Power Cable to the key to remove the three (3) M5 x 50mm screws se- empty 2-pin port on the Power Sensor as indicated curing the brake cover to the unit.
- Page 8 Install HIIT Rower TO ROWER TO WALL STEP 2: Insert the end of the power adapter into STEP 1: Install the power cord into the power adapter. the power inlet located on the console mast. TO WALL STEP 3: Route the power adapter cable as shown in image right, use the zip ties included with the power kit to secure the cable to the HIIT Rower where indicated by the arrows.