Schwinn Airdyne AD6 International model Assembly Manual
Assembly and owner's manual
Hide thumbs
Also See for Airdyne AD6 International model:
- Service manual (58 pages) ,
- Owner's manual (28 pages) ,
- Installation manual (24 pages)
Related Manuals for Schwinn Airdyne AD6 International model
Summary of Contents for Schwinn Airdyne AD6 International model
- Page 1 This product is compliant with the applicable CE requirements. ASSEMBLY MANUAL / OWNER’S MANUAL...
-
Page 2: Table Of Contents
Serial Number __________________________ Date of Purchase ____________________ To register your product warranty, contact your local distributor. If you have questions or problems with your product, please contact your local Schwinn distributor. ® To find your local distributor, go to: www.bowflexinternational.com... -
Page 3: Important Safety Instructions - Assembly
IMpORTANT SAfETY INSTRUCTIONS - ASSEMBLY This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury. Obey the following warnings: Read and understand all warnings on this machine. Carefully read and understand the Assembly instructions. • Keep bystanders and children away from the product you are assembling at all times. -
Page 4: Safety Warning Labels / Serial Number
• Lisez et familiarisez-vous avec le Manuel du www.nautilus.com propriétaire et avec tous les avertissements Phone:1-800-NAUTILUS avant d’utiliser cette machine. Model: Schwinn®Airdyne®AD6 • Soyez prudent lorsque vous utilisez cet Rating: NA équipement pour ne pas vous infliger de graves Class: SA, HA, blessures. -
Page 5: Specifications
SpECIfICATIONS Machine Weight: 52.2 kg (115 lbs.) Power Requirements: 2 AA Batteries (LR6) 129.2 cm Operating Voltage: 1.0 - 3.3VDC ( 50.9” ) Maximum User Weight: 136 kg (300 lbs.) 126.3 cm 65.2 cm Regulatory Approvals: ( 49.7” ) ( 25.7” ) This product conforms to the applicable EN ISO 20957 International Standards for Stationary Training Equipment, Class S DO NOT dispose of this product as refuse. This product is to be recycled. For proper disposal of this product, please follow the prescribed methods at an approved waste center. Before Assembly Select the area where you are going to set up and operate your machine. -
Page 6: Parts
pARTS A decal has been applied to all right (“ R ”) and left (“ L ”) parts to assist with assembly. Item Description Item Description Frame Pedal Strap, Left Console Support Bar Pedal, Left Console Foot Peg, Left Water Bottle Holder Stabilizer, Front Handlebar, Left Foot Peg, Right Seat Pedal, Right Seat Post Pedal Strap, Right Stabilizer, Rear Handlebar, Right... -
Page 7: Hardware
HARdWARE / TOOLS Item Description Item Description Button Head Hex Screw, M8x1.25x20 Washer, M8 Black Washer, M8 Lock Button Head Hex Screw, M8x1.25x12 Black Washer, M8 Tools Included 6 mm 2 AA size batteries (LR6) 13 mm 15 mm 17 mm... -
Page 8: Assembly
ASSEMBLY 1. Attach Stabilizers to Frame Note: Hardware is pre-installed and not on the Hardware Card ( 2. Attach Pedals and then Pedal Straps to Frame Assembly Note: The Left Pedal is reverse-threaded. Be sure to attach Pedals on the proper side of the Bike. Orientation is based from a seated position on the bike. The Left Pedal has an “L”, the Right Pedal an “R”. - Page 9 3. Connect Cables and Attach the Console Support Bar to Frame Assembly Note: Do not crimp the cables. Pull the lower cable to remove any slack as you insert the Console Support Bar. In order to avoid possible serious injury, when inserting the tube ends into the Frame Assembly be careful to avoid fingers or hands being caught or pinched. 4.
- Page 10 5. Connect Cable and Attach the Console Note: Do not crimp Console Cable. 6. Attach Water Bottle Holder to Frame Assembly Note: Hardware is pre-installed and not on the Hardware Card (...
- Page 11 7. Attach Foot Pegs and Handlebar Arms to Frame Assembly 8. Loosen and Pull the Seat Post Adjustment Knob to Attach Seat Post to Frame Assembly...
- Page 12 9. Attach Seat to Seat Post NOTICE: Be sure the Seat is straight and then tighten the hardware. 10. Final Inspection Inspect your machine to ensure that all hardware is tight and components are properly assembled. Do not use or put the machine into service until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s Manual.
-
Page 13: Moving The Machine
BEfORE YOU START Moving the Machine The machine may be moved by one or more persons depending on their physical abilities and capacities. Make sure that you and others are all physically fit and able to move the machine safely. Use the Rear Stabilizer to carefully lift the machine onto the transport rollers. Note: Be sure to keep the fan assembly clear of the floor. Push the machine into position. -
Page 14: Important Safety Instructions
Contact your doctor before you use the machine again. Use the values calculated or measured by the machine’s computer for reference purposes only. • Before each use, examine this machine for loose parts or signs of wear. Do not use if found in this condition. Monitor the Pedals and Crank Arms closely. Contact your local Schwinn distributor for repair information. ® •... -
Page 15: Features
Foot Step Pad Handlebar Leveler Seat Post Adjustment Knob Water Bottle Holder Stabilizer, Front Seat Battery Compartment Foot Peg Locking Knob Pedal Accessories Remote Heart Rate Chest Strap AirDyne Reading Rack AirDyne Wind Screen ® ® contact your local Schwinn distributor To order, ®... -
Page 16: Console Features
Console Features The Console provides information about your workout on the display screen. LCD Display Data The console display shows each workout value. The RPM display fi eld shows the machine revolutions per minute (RPM). The maximum display is 100. Time The TIME display fi eld shows the time count of the workout. The maxi- mum display is 99:59. If the time count is more, the display starts again at 0:00. During the initial power-up, this display will show altitude ( “Alt“ ). The altitude where the machine will be in operation must be entered. Speed The SPEED display fi eld shows the machine speed in kilometers per hour ( “KM” ) or miles per hour ( “M” ), to one decimal place—for example, 3.4... -
Page 17: Remote Heart Rate Monitor
START/STOP button- Starts a Program workout, confirms a selection, and ends a paused workout if held down for 3 seconds. Increase () button- Increases a value (time or altitude) or moves through options Remote Heart Rate Monitor Monitoring your Heart Rate is one of the best procedures to control the intensity of your exercise. The Console can read telemetry HR signals from a Heart Rate Chest Strap Transmitter that operates in the 4.5kHz - 5.5kHz range. Note: The heart rate chest strap must be an uncoded heart rate strap from Polar Electro or an uncoded POLAR com- ® patible model. (Coded POLAR heart rate straps such as POLAR OwnCode chest straps will not work with this ®... -
Page 18: Operations
OpERATIONS What to Wear Wear rubber-soled athletic shoes. You will need the appropriate clothes for exercise that allow you to move freely. How Often Should You Exercise Consult a physician before you start an exercise program. Stop exercising if you feel pain or tightness in your chest, become short of breath, or feel faint. Contact your doctor before you use the machine again. Use the values calcu- lated or measured by the machine’s computer for reference purposes only. • 3 times a week for 20 minutes each day. -
Page 19: Locking The Fan Assembly / Storage
Full Body Workout: Grasp the Hand Grips with your palms down. Push and pull the Handlebars as you pedal, keeping your elbows low and next to your body. Upper Body Workout: Grasp the Hand Grips firmly with palms down and place your feet on the Foot Pegs. Lean slightly forward at the hips with your back straight and shoulders down. Now push and pull the Handlebars Note: You may need to safely push a Pedal to assist with starting the workout. To increase the air resistance and workload, increase your level of activity. To exercise all the muscle groups in your arms, alter your grasp to palms up for part of the workout. -
Page 20: Initial Setup
Initial Setup During the initial power-up, the Console will display “Alt” and must be setup with the current workout altitude. 1. Push the Increase/Decrease buttons to change the value for the altitude. Entering the correct value will make the calorie count more accurate. 2. Push the START/STOP button to set. Note: The altitude value can be adjusted at a future time. To adjust the value, consult the “Console Set-Up Mode” sec- tion. Quick Start Workout The Quick Start program lets you start a workout without entering any information. 1. Sit on the machine. 2. -
Page 21: Console Service Mode
CONSOLE SERVICE MOdE The Console Service Mode lets you set the units of measurement to either English or Metric, see the total time and distance the machine has been used, adjust the altitude value for a more accurate calorie count, or find out which version of Firmware is installed. 1. H old down the Increase button and Decrease button together for 3 seconds while in the Idle Mode to go into the Con- sole Service Mode. 2. T he Console display shows the Units prompt ( “Unit” ). Push START/STOP to start Units option. Push the Increase/ Decrease buttons to change between “M” (Imperial English units) and “KM” (metric units). -
Page 22: Maintenance
MAINTENANCE Read all maintenance instructions fully before you start any repair work. In some conditions, an assistant is required to do the necessary tasks. Equipment must be regularly examined for damage and repairs. The owner is responsible to make sure that regular maintenance is done. Worn or damaged components must be repaired or replaced immediately. Only manufacturer supplied components can be used to maintain and repair the equipment. To reduce the risk of electrical shock or unsupervised usage of the equipment, always remove the batter- ies from the machine and wait 5 minutes before cleaning, maintaining or repairing the machine. Daily: Before each use, examine the exercise machine for loose, broken, damaged, or worn parts. Do not use if found in this condition. Repair or replace all parts at the first sign of wear or damage. After each workout, use a damp cloth to wipe your machine and Console free of sweat. -
Page 23: Replacing The Console Batteries
Replacing the Console Batteries The Console will display “Lbatt” for ten seconds when the batteries are around 10% of their rated power during power up. When replacing the batteries, make sure the batteries point in the +/- direction shown in the battery bay. Note: The console uses AA size batteries (LR6). Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc) batteries. -
Page 24: Maintenance Parts
Maintenance Parts Foot Peg, Right Seat Adjustment Knob Connector Arm Handlebar, Right Frame Arm Pivot Handlebar, Left Stabilizer, Rear Console Cable, Lower Foot Peg, Left Shroud, Left Resistance Fan Assembly Water Bottle Holder Crank Arm, Left Fan Cover Console Center Plate Leveler Locking Knob Pedal, Left GG Stabilizer, Front... -
Page 25: Troubleshooting
Be sure cable is connected securely and oriented properly. connections/orientation Small latch on connector should line up and snap into place. Check Speed Sensor Speed Sensor Magnet should be in place on pulley. Magnet position (requires shroud removal) Check Speed Sensor As- Contact your local Schwinn distributor. ® sembly... - Page 26 Unit rocks/does not sit Check leveler adjustment Leveling feet may be turned in or out to level bike. level Check surface under unit Adjustment may not be able to compensate for extremely un- even surfaces. Move bike to level area. Pedals loose/unit difficult Check pedal to crank con- Pedal should be tightened securely to crank. Be sure connec- to pedal nection tion is not cross-threaded.
- Page 28 Nautilus Bowflex Schwinn Fitness Universal ® ® ® ® 8001314.033113.B...